Mitsubishi Electric FR-E5NP Bedienungsanleitung

TRANSISTORIZED INVERTER INSTRUCTION MANUALFR-E5NP

TRANSISTORIZED INVERTER

HEAD OFFICE:MITSUBISHI DENKI BLDG MARUNOUCHI TOKYO 100-8310

TRANSISTORIZED INVERTER

-INSTRUCTION MANUAL-

FR-E5NP

Profibus DP COMMUNICATION OPTION

IB(NA)-0600007-D (0303) MEE Printed in Japan Specifications subject to change without notice.

A-1

Thank you for choosing the Mitsubishi inverter option unit.

This instruction manual gives handling information and precautions for use of this equipment. Incorrect handling

might cause an unexpected fault. Before using the equipment, please read this manual carefully to use the equipment

to its optimum.

Please forward this manual to the end user.

1. Electric Shock Prevention

This section is specifically about safety matters

Do not attempt to install, operate, maintain or inspect this product until you have read through this instruction

manual and appended documents carefully and can use the equipment correctly. Do not use this product until you

have a full knowledge of the equipment, safety information and instructions.

In this instruction manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

Assumes that incorrect handling may cause hazardous conditions, resulting in

death or severe injury.

Assumes that incorrect handling may cause hazardous conditions, resulting in

medium or slight injury, or may cause physical damage only.

Note that the level may lead to a serious consequence according to conditions. Please follow the

instructions of both levels because they are important to personnel safety.

SAFETY INSTRUCTIONS

!While power is on or when the inverter is running, do not open the front cover. You may get an electric shock.

!Do not run the inverter with the front cover removed. Otherwise, you may access the exposed high-voltage

terminals and charging part and get an electric shock.

!Even if power is off, do not remove the front cover except for wiring or periodic inspection. You may access the

charged inverter circuits and get an electric shock.

!Before starting wiring or inspection, switch power off, wait for more than 10 minutes, and check for no residual

voltage with a tester or the like.

WARNING

CAUTION

WARNING

A-2

2. Injury Prevention

3. Additional instructions

Also note the following points to prevent an accidental failure, injury, electric shock, etc.:

(1) Transportation and mounting

(2) Test operation and adjustment

!Any person who is involved in the wiring or inspection of this equipment should be fully competent to do the work.

!Always install the option unit before wiring. Otherwise, you may get an electric shock or be injured.

!Handle this option unit with dry hands to prevent an electric shock.

!Do not subject the cables to scratches, excessive stress, heavyloads or pinching. Otherwise, you may get an electric shock.

!Apply only the voltage specified in the instruction manual to each terminal to prevent burst, damage, etc.

!Ensure that the cables are connected to the correct terminals. Otherwise, burst, damage, etc. may occur.

!Always make sure that polarity is correct to prevent burst, damage, etc.

!While power is on or for some time after power-off, do not touch the inverter as it is hot and you may get burnt.

!Do not install or operate the option unit if it is damaged or has parts missing.

!Do not stand or rest heavy objects on the product.

!Check that the mounting orientation is correct.

!Prevent screws, metal fragments or other conductive bodies or oil or other flammable substance from entering the inverter.

!Before starting operation, confirm and adjust the parameters. A failure to do so may cause some machines to

make unexpected motions.

WARNING

CAUTION

A-3

(3) Usage

(4) Maintenance, inspection and parts replacement

(5) Disposal

(6) General instruction

!Do not modify the equipment.

!When parameter clear or all parameter clear is performed, each parameter returns to the factory setting. Re-set

the required parameters before starting operation.

!For prevention of damage due to static electricity, touch nearby metal before touching this product to eliminate

static electricity from your body.

!Do not test the equipment with a megger (measure insulation resistance).

!Treat as industrial waste.

All illustrations given in this manual may have been drawn with covers or safety guards removed to provide in-

depth description. Before starting operation of the product, always return the covers and guards into original

positions as specified and operate the equipment in accordance with the manual.

WARNING

CAUTION

CONTENTS

1.PRE-OPERATION INSTRUCTIONS 1

1.1 Packing Confirmation...........................................................................................................................1

1.2 Structure ..............................................................................................................................................2

1.3 Inverter Option Specifications..............................................................................................................3

1.4 Communication Specification...............................................................................................................3

2.INSTALLATION 4

2.1 Pre-Installation Instructions..................................................................................................................4

2.2 Inverter Node Address Setting.............................................................................................................4

2.3 Installation Procedure.........................................................................................................................6

2.3.1 Profibus Communication Cable ....................................................................................................7

3. INVERTER SETTING 9

3.1 Parameter List......................................................................................................................................9

3.2 Operation Mode.................................................................................................................................10

3.2.1 Operation mode switching ..........................................................................................................11

3.3 Operation and Speed Command Source...........................................................................................17

3.4 Operation at Communication Error Occurrence.................................................................................19

3.4.1 Operation selection at communication error occurrence ............................................................19

3.4.2 Alarm and measures...................................................................................................................23

3.4.3 Inverter reset...............................................................................................................................25

4. FUNCTION OVERVIEW 26

4.1 Function Overview.............................................................................................................................26

4.1.1 Output from inverter to master module.......................................................................................27

4.1.2 Input from master module to inverter..........................................................................................28

5.Profibus Device Data 29

5.1 Device Data (GSD file).......................................................................................................................29

5.2 Slave User Parameter........................................................................................................................33

6.Profibus PROFILES—PPO Support Specification 34

6.1 ID definitions......................................................................................................................................35

6.2 Buffer memory map ...........................................................................................................................36

6.3 Buffer Memory Configuration.............................................................................................................37

6.4 Buffer Memory Details .......................................................................................................................38

6.4.1 Points to note..............................................................................................................................43

7.Profibus PROFILES—PPO Non Support Specification 44

7.1 ID definitions......................................................................................................................................45

7.2 Buffer memory map ...........................................................................................................................45

7.3 Buffer Memory Configuration.............................................................................................................46

7.4 Buffer Memory Details .......................................................................................................................47

7.4.1 Points to note..............................................................................................................................51

8.PARAMETER DEFINITIONS—PPO Support Specification 52

8.1 Outline of PNU...................................................................................................................................52

8.2 Profibus PNU.....................................................................................................................................53

8.2.1 Real-time monitor........................................................................................................................53

8.2.2 Parameter clear ..........................................................................................................................53

8.2.3 Operation mode read/write .........................................................................................................54

8.2.4 Set frequency read......................................................................................................................54

8.2.5 Terminal input read.....................................................................................................................54

8.2.6 Inverter reset...............................................................................................................................54

8.2.7 Node address read .....................................................................................................................55

8.2.8 Alarm history...............................................................................................................................55

8.2.9 PNU list read...............................................................................................................................57

8.3 Standard Parameters.........................................................................................................................58

9.PARAMETER DEFINITIONS—PPO Non Support Specification 60

9.1 Outline of PNU...................................................................................................................................60

9.2 Profibus PNU (Module type E5NP)....................................................................................................60

9.2.1 Real-time monitor (IND = 0000H) ...............................................................................................60

9.2.2 System environment variable (sev) area (IND = 01PPH) ...........................................................61

9.3 Standard Parameters.........................................................................................................................65

9.3.1 Normal parameter area (IND = 0200H) ......................................................................................65

9.3.2 Pr. 900 and later-frequency parameter area (IND = 0300H) ......................................................67

9.3.3 Pr. 900 and later-% parameter area (IND = 0400H)...................................................................67

10.TROUBLESHOOTING 68

1.PRE-OPERATION INSTRUCTIONS

Take the option unit out of the package, check the unit name, and confirm that the product is as you ordered and

intact.

This product is a plug-in option unit designed for exclusive use in the Mitsubishi FR-E500 series inverter (FR-

E540-0.4K to 7.5K (-NA) (-EC) (-CH), FR-E520S-0.4K to 2.2K-EC (-CH)).

1.1 Packing Confirmation

Make sure that the package includes the following

• Instruction manual...........................................................................1

• Mounting screws M3 × 6 .................................................................2

• LED indication sticker......................................................................1

PRE-OPERATION INSTRUCTIONS

1.2 Structure

FR-E5NP

Mounting hole

Connector

Operating status

indicator LED

Profibus Connector

(Dsub9 pin connector)

Mounting

hole

Node address

setting switch

X16 X1

SERIAL

Name Function

Node address setting

switches

Used to set the inverter node

address between 0Hand 7DH.

For details, refer to page 4.

Operating status

indicator LED (green) off Communication stops

on During communication

Profibus connector

(Dsub9 pin connector)

Used to connect a Profibus

cable for Profibus

communication (Refer to page

7.)

PRE-OPERATION INSTRUCTIONS

1.3 Inverter Option Specifications

* When the option unit (FR-E5NP) is plugged in, the protective structure (JEM1030) is open type (IP00).

1.4 Communication Specification

Type Inverter inboard option, to be connected with a connector (can be mounted/dismounted

to/from the inverter front face)

Number of node occupied One inverter occupies one node.

Communication cable For 12Mbps communication

(compliant with EEIA-RS-485 standard)

Communication

speed

Wiring length 1200m maximum 9600bps, 19.2Kbps, 93.75Kbps

Wiring length 600m maximum 187.5Kbps

Wiring length 200m maximum 500Kbps, 1.5Mbps

Wiring length 100m maximum 3Mbps, 6Mbps, 12Mbps

Inhaltsverzeichnis

Andere Mitsubishi Electric Wechselrichter Handbücher

Mitsubishi Electric

Mitsubishi Electric FR-A7NC E kit-SC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric A800 Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E8AXY E KIT Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FREQROL-CS80 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F720-00046 Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-D720-008 Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-A7AX E kit-SC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-D720S-008SC Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E720-600 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A5AP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-E520 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-AF700-EC Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-A7AZ Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-S520E Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-D700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A500L Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-HEL-0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7AP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F800 Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung