Mitsubishi Electric MP-G10-AO Bedienungsanleitung

INDUSTRIAL SEWING MACHINE

Attachment

MODEL

MP-G10-AO

TECHNICAL MANUAL

Pneumatic Type Clamp

A180E627P03

FOR SAFE USE

Before the installation, operation, and inspection for this product, read the “FOR SAFE USE” and the

technical manuals carefully. Also read the other technical manuals, “Sewing Machine Head”, “Control

Unit” and “Operation Panel” describing some instructions, which are not in this manual, and use the

sewing machine properly.

SAFETY INDICATIONS

CAUTION

Indicates that incorrect handling may cause hazardous conditions, resulting

in medium or slight personal injury or physical damage. Note that CAUTION

level may lead to a serious consequence according to the circumstances.

Always follow the instructions of both levels because they are important to

personal safety.

CAUTION INDICATIONS

No.

Caution indication Description

Precaution for sewing machine operation:

Indicates that removing the safety and operating

the sewing

machine for some other purposes with power-on are prohibited.

Please do not operate the sewing machine without

protective equipment such as a needle guard, an eye guard,

a belt cover or the others.

Please turn off the power switch when threading, changing

a needle and a bobbin, cleaning, and lubricating.

Caution for fingers injury:

Indicates a possibility of fingers (hands) injury in a certain

condition.

Caution for squeezing fingers:

Indicates a possibility of squeezing fingers in a certain condition.

1. Features

The pneumatic type clamp is used to increase or decrease the force applied on the material to be

stitched, and to adjust the pressing speed. This clamp is effective if the material to be stitched is heavy

and the magnetic type clamp is too weak to hold the material, or if the material is soft and needs to be

gently pressed.

2. Specifications

Name ：MP-G10-AO (pneumatic type clamp)

Applicable model: ：PLK-G1010

Sewing area ：100 (X) mm X 100 (Y) mm (same as PLK-1010）

Clamp UP position ：30 mm

Pressing operation ：Use foot switch (2-pedal) normally provided with the

electronic sewing machine.

Drive source air

pressure Primary side ：0.5 MPa（5 kg/cm2）or more

Secondary side: ：0.4 MPa（4 kg/cm2）

Trouble such as operation errors could occur if the secondary pressure is set too high.

Use within the range of 0.4 MPa (4 kg/cm2).

CAUTION

- 1 -

3. Configuration

★The Fig. numbers in the drawing correspond to the part numbers given in the following explanations.

3.1 Clamp mechanism

119

- 2 -

3.1 Clamp mechanism (Parts list)

Fig 部品コード品名Description

数量

No. Parts No. Amt. Req.

101 M91055020 ﾛｯｶｸｱﾅﾂｷﾄﾒﾈｼﾞ M4X4 Screw M4X4 4

102 MH10A0352 ｶﾗｰ Collar 2

103 M90519050 ﾅｲﾛﾝﾜｯｼｬ Nylon washer 4

104 M91109002 ﾋﾗﾈｼﾞ 11/64(40)X7 Screw 11/64(40)X7 2

105 M90421050 ｻﾞｶﾞﾈ 4 Washer 4 2

106 MH10K0950 ﾚﾊﾞｰ(S2L) Lever (S2L) 1

107 MH10K1950 ﾚﾊﾞｰ(S1) Lever (S1) 2

108 M90538060 ﾅｯｸﾙﾋﾟﾝ(L) Knuckle pin (L) 1

109 ME10P0434 ｴｱｼﾘﾝﾀﾞ Air cylinder 2

110 ME10P0352 ｶﾗｰ Collar 2

111 M93004021 ﾛｯｶｸｱﾅﾂｷﾎﾞﾙﾄ M3X5 Socket bolt M3X5 4

112 MH10A1308 ｵｻｴﾀﾞｲ Clamp bracket 1

113 MH10K0601 ｼﾘﾝﾀﾞﾄﾘﾂｹｲﾀ Cylinder bracket 1

114 M94002017 ｾﾌﾃｨｿｹｯﾄ M4X8 Safety socket bolt M4X8 4

115 M90555060 ﾋﾟﾝ Pin 1

116 M90548060 ﾅｯｸﾙﾋﾟﾝ(R) Knuckle pin (R) 1

117 MH10K2950 ﾚﾊﾞｰ(S2R) Lever (S2R) 1

118 M90822060 ﾋﾟﾝ Pin 1

119 MH10A0105 ｵｻｴ Clamp frame 1

120 M94003017 ｾﾌﾃｨｿｹｯﾄ M3X6 Safety socket bolt M3X6 2

121 MH10A4477 ｽﾄｯﾊﾟ Stopper 2

122 M94008070 ﾛｰﾗﾘﾃｰﾅ Roller retainer 4

123 M94019017 ｾﾌﾃｨｿｹｯﾄ M4X14 Safety socket bolt M4X14 6

124 MH10A6957 ｵｻｴｺﾃｲﾚｰｽ Fixed race 2

125 MH10A3957 ｵｻｴｲﾄﾞｳﾚｰｽ Movable race 2

126 MH10A4957 ｵｻｴｺﾃｲﾚｰｽ Fixed race 1

127 MH10A3601 ｵｻｴﾄﾘﾂｹｲﾀ Clamp foot 1

128 M95005017 ｾﾌﾃｨｿｹｯﾄ M5X10 Safety socket bolt M5X10 4

129 M94005022 ﾛｯｶｸｱﾅﾂｷﾎﾞﾀﾝﾎﾞﾙﾄ M4X8 Bolt M4X8 2

130 M90422050 ｺｻﾞｶﾞﾈ 4 Washer 4 4

131 M94041021 ﾛｯｶｸｱﾅﾂｷﾎﾞﾀﾝﾎﾞﾙﾄ M4X6 Bolt M4X6 2

132 MH10A0196 ｲﾁｷﾞﾒｲﾀ Guide plate 2

- 3 -

3.2 Pneumatic pressure control unit

3.3 Accessories

- 4 -

3.2 Pneumatic pressure control unit (Parts list)

Fig 部品コード品名Description

数量

No. Parts No. Amt. Req.

201 MH25A1601 ﾃﾞﾝｼﾞﾍﾞﾝﾄﾘﾂｹｲﾀ Valve mounting plate 1

202 M91066004 SW-PW ﾌﾟﾗﾏｲﾅﾍﾞﾈｼﾞ M4X25 Screw M4X25 4

203 ME10X0599 ﾃﾞﾝｼﾞﾍﾞﾝｸﾐﾀﾃ Solenoid valve assy 1

204 M90511050 ｻﾞｶﾞﾈ 5 Washer 5 2

205 M95003017 ｾﾌﾃｨｿｹｯﾄ M5X8 Safety socket bolt M5X8 2

206 MB10B0508 ｾﾂｿﾞｸﾃﾞﾝｾﾝｸﾐﾀﾃ Cable assy 1

207 ME10X1567 ｴｱﾁｭｰﾌﾞｸﾐﾀﾃ(A) Air tube assy (A) 1

208 ME10X0567 ｴｱﾁｭｰﾌﾞｸﾐﾀﾃ(B) Air tube assy (B) 1

209 M91035089 ｻｲﾚﾝｻ Muffler 2

210 MB20P1567 ｴｱﾁｭｰﾌﾞ Air tube 1

211 ME40A0963 ﾌｨﾙﾀﾚｷﾞｭﾚｰﾀ Filter regulator 1

212 MA20A8571 L ｶﾞﾀﾜﾝﾀｯﾁﾂｷﾞﾃ L-type quick joint 3

3.3 Accessories (Parts list)

Fig 部品コード品名Description

数量

No. Parts No. Amt. Req.

301 MF06A1620 ｹｯｿｸﾊﾞﾝﾄﾞ Cable tie 4

302 M94007099 ﾅｲﾛﾝｸﾘｯﾌﾟ 6 Nylon clip 6 1

303 M91054004 SW-PW ﾌﾟﾗﾏｲﾅﾍﾞﾈｼﾞ M4X8 Screw M4X8 2

304 MB60A1620 ﾅｲﾛﾝｸﾘｯﾌﾟ 8 Nylon clip 8 1

305 M90409041 ﾏﾙﾓｸﾈｼﾞ 4.5X20 Wooden screw 4.5X20 2

306 MH10C0691 ﾊﾟｯｷﾝｾｯﾄ Clamp pad 1

307 ME10P0691 ﾊﾟｯｷﾝ Pad 1

308 MB10X0742 ﾌﾀ Cap 1

309 M94005022 ﾛｯｶｸｱﾅﾂｷﾎﾞﾀﾝﾎﾞﾙﾄ M4X8 Bolt M4X8 4

310 M91010089 ﾛｯｶｸｿｹｯﾄ Socket 1

311 MA30A0571 ﾜﾝﾀｯﾁﾂｷﾞﾃ Quick joint 1

312 MS06A0567 ｴｱﾁｭｰﾌﾞ Air tube 1

- 5 -

4. Setup procedures

4.1 Installing the clamp drive mechanism

(1) Remove the four screws on the Y axis movement race side fixing the clamp base (Fig.No.112) and

the two screws on the axis support side, and remove the magnetic clamp mechanism mounted as

a standard on the sewing machine.

(2) Using the screws removed above,install this pneumatic clamp mechanism following the above step

in reverse. Make sure that the clamp is not inclined at this time.

(3) If there is no need to reinstall the magnetic clamp mounted as a standard on the sewing machine

after changing to the pneumatic type clamp, it is recommended to remove the drive mechanism

parts in the sewing machine head.

To remove these parts, refer to the part catalog P-246 for the PLK-G1010 sewing machine unit, and

remove the parts (except No.120) in page14 of the catalog. Use the parts Fig.No.307, 308, and 309

which enclosed with this attachment as a cover.

4.2 Installing the pneumatic pressure control related parts

(1) The regulator and solenoid valve assembly configured of Fig.No.201, etc., are fixed to the bottom of

the sewing machine table with the enclosed Fig.No.305 wood screws (two screws).

(2) Align the piping symbols of the Fig.No.207 and 208 air tubes (φ4) with ports A to B on the

pneumatic clamp's Fig.No.109 air cylinder, and insert the tubes.

(3) Pass the air tubes through the notched section on the side of the sewing machine unit's motor cover,

and lead the tubes to the bottom of the table from the square hole on the table.

(4) Align the air tubes led out above with the ports A to B of the solenoid valve installed in step (1), and

insert the tubes.

(5) Bind the air tubes appropriately with the enclosed Fig.No.301 Cable ties.

4.3 Connecting the switches and cables

(1) Remove the cover for the connector panel on the back of the sewing machine.

(2) Disconnect the cable connected to CON13 (FU) on the solenoid PCB. This cable is not used after

this attachment is mounted. Fix it where it will not obstruct the other electric parts.

(3) Lead out the Fig.No.206 cables connected to the solenoid valve from the slot on the back of the

sewing machine table, pass through the cord bushing on the connector panel, and lead in to the

solenoid PCB side.

(4) Insert the Fig.No.206 cable connector to CON13 (FU) on the PCB from where the cable was

disconnected above.

(5) This completes the connection of the wiring. Check the connection with the following table, and

then securely install the cover removed from the connector panel.

Always make sure that the power is OFF before starting setting work.

CAUTION

- 6 -

Signal name Connection

Sewing machine head solenoid PCB

CON13 (FU) - ②

Work holder ouput 1 Sewing machine head solenoid PCB

( O4 ) CON13 (FU) - ①

Output

Fig.No.206

+24V

4.4 Installing the system software

(1) Installing the System Software

①While holding down the [F] key on the front panel of the control box, turn the machine power ON.

(Keep pushing [F] key until red LED on the front panel is turned on.)

②[Model and language set function] screen is displayed.

③Press the . Select the on the language set function screen then, press

the .

④Press the . Select the on the model set function screen then, press

the .

⑤Press the to determine the settings.

⑥After [INITIALIZES SET VALUE] message is displayed, press the .

This completes installing the system software. Turn off the power switch once.

4.5 Setting change

(1) Press the on the standard screen to open the MENU mode.

(2) Press the in the menu icon. The Input/Output setting mode screen is displayed.

(3) Press the on the Input/Output setting mode.

Black

White

Solenoid

valve

When this sewing machine is already used, installation explained by this 4.4 clause is not

necessary.

1010

If the sewing machine is operated with the magnetic clamp settings, faults could occur.

Always install the system software for the pneumatic type clamp.

CAUTION

- 7 -

(4) Enter a password

(5) Press the inside of the frame under the .

(A display in the frame is OF1 in a standard setting. If it is the other display, change to OF1.)

* Refer to the clause Output confirmation (Custom output) [of 2.Explanation of input/output

setting mode of [14]Input/output setting mode] of the technical manual ”Operation Panel” for the

change method to OF1.

(6) Press the .

(7) Press the .

(8) Press the several times.

And make display .

(9)Press the .

(10)Press the two times.

(11)Press the and return to standard screen.

The settings will be changed to the table shown below by the above operation.

Mode Input/output setting

Function name O4

Pneumatic type clamp 4mS=ON 2mS=OFF 66%

Factory setting 2mS=ON 4mS=OFF 33%

Remarks

Set this when changing from the magnetic

clamp to the pneumatic clamp.

[chopping duty setting of details screen(2)]

For details, refer to the clause [14]Input/output setting mode of the technical manual “Operation

Panel”.

Please ask the dealer about a password.

DETAILED

SETTING

2ms ON, 4ms OFF, 33% Duty

4ms ON, 2ms OFF, 66% Duty

- 8 -

Inhaltsverzeichnis

Andere Mitsubishi Electric Nähmaschine Handbücher

Mitsubishi Electric

Mitsubishi Electric PLK-G3040R Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J2516R-YU Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G4030R Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G5050 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LAN UNIT Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-E SERIES Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J3020R-SE Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J10050R3 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J4040RH Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J6040 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MP-J-PP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LU2-4710-B1T Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J10050RH Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G2010R Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J2516-YU Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G4030 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G5050R Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G2516R Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric XC-G500-Y Handbuch

Mitsubishi Electric

Mitsubishi Electric PLK-G2008H Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric DY-253 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-J Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LT2-2250-B1T Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLK-G3040R Bedienungsanleitung

Beliebte Nähmaschine Handbücher anderer Marken

Riccar

Riccar RL634DE Bedienungsanleitung

Pfaff

Pfaff 3307-1 SERIES Bedienungsanleitung

Siruba

Siruba C007JP Bedienungsanleitung

Husqvarna Viking

Husqvarna Viking Designer SE Bedienungsanleitung

Singer

Singer 148-5 Bedienungsanleitung

IKEA

IKEA SY Bedienungsanleitung

Pfaff

Pfaff 571 Bedienungsanleitung

Singer

Singer 15-91 Bedienungsanleitung

Brother

Brother BB370 Bedienungsanleitung

Pegasus

Pegasus WT100 Series Bedienungsanleitung

Reliable

Reliable 7100DB Bedienungsanleitung

Pfaff

Pfaff 937 Bedienungsanleitung

Singer

Singer 6038 Bedienungsanleitung

Singer

Singer 413K Bedienungsanleitung

Pfaff

Pfaff 1471 E1 Bedienungsanleitung

Kenmore

Kenmore 16677 - Serger Sewing Machine Bedienungsanleitung

HIGHLEAD

HIGHLEAD GC2008-M Bedienungsanleitung

Singer

Singer 400W4 Bedienungsanleitung