Molex 35745 Series Bedienungsanleitung

Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals

Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 1 of 6

Revision: B Revision Date: 10-13-10

TYPE 4A

Application Tooling

Specification Sheet

Modular Cri p Head

Order No. 63819-6970

Hand Cri p Tool

Order No. 63819-6900

FEATURES

% full cycle ratcheting hand tool ensures complete crimps

% Ergonomically designed soft handles

% Precisely designed crimping profiles with simple contact positioning

% Easy handling due to outstanding force ratio

% Modular Crimp Head is removable and can be use in the ir Powered Tool Order No.63816-0100,

accompanied by ir Powered Crimp dapter (Order No. 63816-0700).

% Can also be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63816-0250 (220 V)

accompanied by Battery Powered Crimp dapter (Order No. 63816-0600).

SCOPE

Products: VersaBlade™ Industry standard .070" tab terminals, 24 – 26 WG

Ter inal

Series No.

Ter inal

Order No.

Wire Size Insulation Dia eter Strip Length

IPC/WHMA-A620 Ter inal

AWG ² In. In. In.

35745 35745-0410 24 0.20 1.32-1.45 .052-.057 1.32-1.45 .052-.057 4.0-4.8 .157-.189

26 0.12

35746 35746-0410

35746-0411

24 0.20 1.32-1.45 .052-.057 1.32-1.45 .052-.057 4.0-4.8 .157-.189

26 0.12

35747 35747-0410 24 0.20 1.32-1.45 .052-.057 1.32-1.45 .052-.057 4.0-4.8 .157-.189

26 0.12

35748 35748-0410

35748-0411

24 0.20 1.32-1.45 .052-.057 1.32-1.45 .052-.057 4.0-4.8 .157-.189

26 0.12

To achieve optimum IPC- 620 insulation crimps, use this insulation OD range.

Overall insulation OD specification for terminal.

Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals

Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 2 of 6

Revision: B Revision Date: 10-13-10

INSULATION

CRIMP

▲

SEE NOTE

BRUSH

STRIP

LENGTH

BELL MOUTH

CRIMP HEIGHT

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP

TWISTING

DEFINITION OF TERMS

▲Insulation Cri p Note:

Due to the terminal’s insulation grip design and/or

insulation diameter range, this tool uses “overlap”

form geometry in the insulation punch. This produces

an overlap insulation crimp ( 620 – compliant). While

the insulation punch profile may appear “lopsided”,

this is a normal condition for this tool. See figure to

the right. (Some tools with multiple crimp pockets

may not have the “overlap” profile on all pockets).

CONDITIONS:

fter crimping, the crimp profiles should measure the

following (see notes on page 4).

Ter inal

Series No

Wire Size Conductor Cri p (Ref.) Insulation Cri p (Ref.) Pull Force

Mini u Profile

Height Width Height ( ax)

Width

AWG

In. In. In. In. N Lb. 24

35745 24 0.20

1.00-1.10

.039-.043

1.60-1.80

.063 -.071

2.55 .100 2.30-2.50

.091-.098

29.4

6.61

26 0.12

0.90-1.00

.035-.039

1.60-1.80

.063 -.071

2.45 .097 2.30-2.50

.091-.098

19.6

4.41

35746 24 0.20

1.00-1.10

.039-.043

1.60-1.80

.063 -.071

2.55 .100 2.30-2.50

.091-.098

29.4

6.61

26 0.12

0.90-1.00

.035-.039

1.60-1.80

.063 -.071

2.45 .097 2.30-2.50

.091-.098

19.6

4.41

35747 24 0.20

1.00-1.10

.039-.043

1.60-1.80

.063 -.071

2.55 .100 2.30-2.50

.091-.098

29.4

6.61

26 0.12

0.90-1.00

.035-.039

1.60-1.80

.063 -.071

2.45 .097 2.30-2.50

.091-.098

19.6

4.41

35748 24 0.20

1.00-1.10

.039-.043

1.60-1.80

.063 -.071

2.55 .100 2.30-2.50

.091-.098

29.4

6.61

26 0.12

0.90-1.00

.035-.039

1.60-1.80

.063 -.071

2.45 .097 2.30-2.50

.091-.098

19.6

4.41

Pull Force should be measured with no influence from the insulation crimp.

The above specifications are guidelines to an optimum crimp.

OPERATION

Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will

release the handles, and the hand tool will spring open.

OVERLAP

INSULATION

CRIMP

OVERLAP FORM GEOMETRY

ANVIL

PUNCH

WIRE

Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals

Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 3 of 6

Revision: B Revision Date: 10-13-10

WIRE

INSULATION

PUNCH

TERMINAL

WIRE STOP BLADE

Figure 1

Figure 2

WIRE

TERMINAL

LOCATOR

INSULATION

PUNCH

INSULATION

ANVIL

WIRE STOP

BLADE

CONDUCTOR ANVIL

CONDUCTOR

PUNCH

Cri ping Ter inals

1. Place the terminal into the correct die profile until the terminal stopped by the locator.

2. Bring the wire stop blade down; make sure the wire stop located behind the conductor grip.

3. Place a pre-striped wire into the terminal until the end of wire touching the wire stop. See Figure 2.

4. Close the tool until the ratchet releases, the tool handles will then spring open.

5. Carefully remove the crimped terminal.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible for, the following

maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine

oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs

cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight

automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life.

4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto

certain terminations may affect the electrical characteristics of an application.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscri ps or Ja s

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by lifting the ratchet release lever. See Figure 6.

Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals

Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 4 of 6

Revision: B Revision Date: 10-13-10

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. ll vital

components are long life tested. ll tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will

not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. ny clamping,

fixturing, or use of handle extensions voids this warranty.

CAUTION: Repetitive use of this tool should be avoided.

CAUTIONS:

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

Notes:

1. This tool should only be used for the terminals and wire gauges specified on this sheet.

2. This tool is not adjustable for crimp height; however crimp force is adjustable (See instructions above).

Variations in tools, terminals, wire stranding and insulation types may affect crimp height.

3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all

insulation sizes.

4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts

available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.

5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no

influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips

on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping

Handbook 63800-0029 for additional information on crimping and crimp testing.

6. Molex does not certify crimp hand tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals

Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 5 of 6

Revision: B Revision Date: 10-13-10

MODULAR

CRIMP

HEAD

BATTERY

POWER

LOCKING

PINS

LOCKING PINS

BATTERY

POWERED

TOOL

AIR

POWER

TOOL

MODULAR

CRIMP HEAD

LOCKING

PINS

LOCKING

PINS

AIR

POWER

CRIMP

ADAPTER

Applications for the Modular Cri p Head

WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction

and without first reading and understanding the instructions in the proper Manual or Specification Sheet.

See Chart below for the correct Manual or Specification Sheet.

WARNING: NEVER install tooling or service this tool while it is into any power source. Disconnect the

power by unplugging or turn off the ctuator from its power source.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

The chart below shows all applications for this Modular Crimp Head.

Modular Cri p Head

Order No.

Tool

Order no.

Tool

Description

Adapter

Order No.

Adapter

Description

Figure

No.

63819-6970

63816-0000

Hand Crimp Frame (Short) N/ N/ 3

63816-0050

Hand Crimp Frame (Long) N/ N/ 3

63816-0200

Battery Power Tool (110 V)

63816-0600

Battery Power Crimp dapter

63816-0250

Battery Power Tool (220 V)

63816-0600

Battery Power Crimp dapter

63816-0100

ir Power Tool 63816-0700

ir Power Crimp dapter 5

Applications for the Modular Cri p Head

Hand Cri p Tool Battery Powered Tool Air Powered Tool

Figure 3 Figure 4 Figure 5

MODULAR

CRIMP

HEAD

LOCKING

PINS

HAND CRIMP

FRAME LONG

OR SHORT

Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals

Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 6 of 6

Revision: B Revision Date: 10-13-10

RATCHET

RELEASE LEVER

HANDLE

SPRING

CRIMPING

SPRING (2)

Figure 6

M4 X 14

LONG BHCS

PARTS LIST

Hand Cri p Tool 63819-6900

Ite

Order Nu ber

Description Quantity

1 63819-6970 Modular Crimp Head 1 (Ref)

2 63816-0050 Hand Crimp Frame (long)

1 (Ref)

3 63819-6975 Locator 1

4 63816-0001 Locking Pin 2

5 63600-0525 Handle Spring 1

6 63600-0520 Crimping Spring 2

http://www.molex.com

Andere Handbücher für 35745 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere molex Crimpwerkzeuge Handbücher

molex

molex 63811-9200 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63816-1000 Bedienungsanleitung

molex

molex 63827-8200 Bedienungsanleitung

molex

molex 64001-7400 Bedienungsanleitung

molex

molex CR60670B Bedienungsanleitung

molex

molex AT 1991 Bedienungsanleitung

molex

molex 63827-6270 Bedienungsanleitung

molex

molex 63825-8000 Bedienungsanleitung

molex

molex 63825-9400 Benutzerhandbuch

molex

molex 63823-8700 Benutzerhandbuch

molex

molex 207129 Series Bedienungsanleitung

molex

molex RHT 2251-CC Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63819-3500 Bedienungsanleitung

molex

molex 200218-2600 Benutzerhandbuch

molex

molex RHT-4754 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63827-6070 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 213309-1400 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63825-6670 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung

molex 35745 Series Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken