Molex 57022 Series Bedienungsanleitung

INSTRUCTION MANUAL NO.

IS-0117E

ISSUED 2001-06-01

REVISED 2005-01-13

REV. A

STRAIGHT-ACTION (SHORT-HANDLE

TYPE) HAND CRIMP TOOL

OPERATING MANUAL

Molex Japan Co., Ltd.

Molex Japan Co., Ltd. Contents of Update Instruction Manual No. IS-0117E

Title Straight-Action (Short-Handle Type) Hand Crimp Tool Tool Number

Rev. Issued Description

0 2001/06/01 New creation release.

Prepared by Y. Ishiwata

Checked by T. Yoshida

A 2005/01/13 Changed the form into the bilingual version.

ECN-JM50012 Approved by A. Horino

A–1

Please read the following before operating the tool.

1. Introduction

Thank you for choosing our Hand Crimp Tool.

This document is prepared so that the tool is properly used.

Please take the time to read this manual, making sure you understand the operating

procedures described herein before attempting to operate the tool.

2. Dangerous operations

1) Don’t insert a part of your body or other foreign materials in the hand crimp tool

(hereinafter referred to as the “tool”) while you’re operating the handle of a tool, as injury

my result.

2) Beware of a handle when it is opened. Releasing a ratchet may cause the handle to open

abruptly, resulting in injury.

3) Only users who have received adequate training on usage and safety from their manager,

and have appropriate knowledge and skills must use the tool. Use by unfamiliar users may

cause injury.

1) Unauthorized reproduction of this document in part or in whole is prohibited.

2) The contents of this document are subject to change without notice.

3) Molex Japan Co., Ltd. assumes no responsibility for losses resulting from use or

misuse of this document.

A–2

Please read the following before operating the tool.

3. Careful handling

1) Always check the tool number, applicable terminal and wire size, etc. before using the tool

in the crimping process.

2) Check the tool for any damage, and repair prior to use. Defective crimping may result in

fire.

3) Clean the tool regularly if used frequently.

4) Avoid storing the tool in extremes of temperature, or high-humidity environment.

5) Keep the tool in a place out of reach of children in order to prevent accidents.

4. Must not be carried out

1) Use the tool only for the intended purpose. Don’t use it in place of a hammer, pliers, or other

tools. Don’t remodel the tool. Parts damage may result in accident or injury.

2) Don’t use the tool for unspecified terminals. Don’t crimp unspecified wires. Both may cause

parts damage.

3) The ratchet mechanism of the tool is designed based on operation by the grip of the hand.

Note that improper handling such as inserting it into other devices and opening the handle

forcibly may decrease its capabilities and lifespan.

Page 1

1. Description

This tool is a straight-action (short-handle type) hand crimp tool, which is designed for

crimp-connecting wires to crimp terminal of Molex.

Please confirm the tool number, the applicable terminal number, and the size of the

applicable wire marked on the hand crimp tool before attempting to operate this tool.

2. Tool Specification

1) Tool name:

Straight-Action (Short-Handle Type) Hand Crimp Tool

2) Outer dimensions and

weight:

215 (width) x 90 (depth) x 15 (thickness) mm, Approx. 400gf

3) Management method:

Crimp height and crimp strength (Details are described to the

crimp specification of a corresponding tool)

4) Part names of tool

Grip

Handle

Ratchet adjustment screw & Fixing nutHead

Crimp section

Link

215 mm

Ratchet part

Page 2

3. Operation Method

1) Hold the tool handle, and squeeze it until the ratchet is released. Then, unclench your hand.

The handle will be opened by the return spring.

2) Insert a “terminal (1)” into the “crimp section (3)” from the “molex logo mark side (2).” Insert

a “terminal (1)” so that the “molex logo mark side (2)” faces the “contact”, and the “terminal

number engraving side (4)” faces the “barrel (5).”

3) Close the handle lightly until the “barrel (5)” of a “terminal (1)” is held by the “insulation

punch (6)” and “anvil (7).” At this time, the tip of a “locator (8)” is placed between the

“conductor barrel (9)” and the “insulation barrel (10)” so that the “terminal (1)” does not

come off.

* Don’t tighten the handle excessively, as doing so may cause deformation of the crimp part

of a terminal and prevent insertion of a wire.

Insulation barrel (10)

Conductor barrel (9)

nvil (7)

Direction of terminal

insertion

Locator (8)

Insulation punch (6)Conductor punch

Insulation end face (12)

Wire (11)

molex logo mark side Terminal number engraving side

Terminal number engraving side (4)Crimp section (3)

molex logo mark side (2)

Barrel (5)

Terminal (1)

Page 3

3. Operation Method (continued)

4) Insert the stripped “wire (12)” from the “terminal number engraving side (4)” until the

“insulation end face (12)” contacts the “locator (8).”

5) Squeeze the tool handle firmly until the ratchet is released (clicks), while holding the wire in

the same position as in below figure.

6) When the ratchet clicks and is released, the handle is automatically opened by the return

spring, and the terminal is crimped.

7) Holding and pulling the “wire (11)” toward the handle gently removes the crimped terminal.

“Note” Don’t tighten the handle excessively after the ratchet is released, as doing so may

over-crimp the terminal and cause wire breakage of parts damage.

Wire strip length

Insulation crimp height (reference)

Conductor crimp height

Extrude wire length

Page 4

4. Daily Maintenance

4.1. Machinery Inspection and Adjustment

1) Check to confirm that the handle moves smoothly (as heeded).

2) After using the tool, always apply machine oil or commercial anti-corrosive oil to the crimp

section, the link, the ratchet, and other moving parts prior to storage (as needed).

3) Loosen the fixing nut for ratchet adjustment screw (eccentric shaft) shown in below figure

by attached “exclusive tool”, and rotate the ratchet adjustment screw to change the position

at which the ratchet is released.

Always adjust the position when the crimp section cannot be fully closed due to parts wear

or the like. Be sure to retighten the fixing nut after completion of adjustment.

Ratchet adjustment screw

Crimp section

Ratchet part

Fixing nut

Page 5

4.2. Crimp Terminal Inspection

1) Crimp height of conductor wire (Crimp height)

(1) Always check the crimp height of a conductor wire at the beginning and end of daily

operation, and also check it regularly during operation.

(2) Refer to the specification table provided with the tool for crimp height.

(3) When the crimp height of a conductor wire is not in accordance with the specification, the

tool has damaged or reached the end of its lifespan. Please consult our service personnel.

(4) As this tool crimps wires of various sizes using one set teeth, the insulation crimp height is

for reference only.

“Note” We recommend to measure the crimp height of a conductor

wire by using the “crimp height micrometer” (J5830-001) of

Molex.

Wire strip length

Insulation crimp height (reference)

Conductor crimp height

Extrude wire length

Measurement of crimp

height of conductor wire

J5830-001

Page 6

4.2. Crimp Terminal Inspection (continued)

2) Wire pullout strength

(1) Be sure to check the wire pullout strength regularly.

(2) Create a test sample like one the below figure and place it in a pullout force tester or a pull

gauge. Then apply the standard pullout force of 25 mm/min. to it, and measure the value at

the point where the wire is pulled out or fractured.

(3) Remember that the insulation section should not be crimped.

3) Crack or deform of terminal

Always check to confirm that the crimped terminal is not cracked or deformed.

Do not crimp the insulation section. Pull out by the speed of 25 mm/min.

150 mm

20 mm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere molex Crimpwerkzeuge Handbücher

molex

molex 63903-8900 Bedienungsanleitung

molex

molex 63827-8770 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex CR60622B Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex CR60670B Bedienungsanleitung

molex

molex 11-01-0101 Bedienungsanleitung

molex

molex 63811-5500 Bedienungsanleitung

molex

molex 63825-6770 Bedienungsanleitung

molex

molex 63816-0800 Bedienungsanleitung

molex

molex 63825-6670 Bedienungsanleitung

molex

molex 78172 Series Bedienungsanleitung

molex

molex CR5907 Bedienungsanleitung

molex

molex 64005-0900 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 64001-7400 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 19294-0008 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63823-6470 Bedienungsanleitung

molex

molex 63825-8100 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung

molex 57022 Series Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken