Molex 63819-2900 Bedienungsanleitung

Hand Crimp Tool For Low Force Micro-Fit 3.0™ Crimp Terminals

Doc No: ATS- 38192900 Release Date: 12-10-08 UNCONTROLLED COPY Page 1 of 7

Revision: B Revision Date: 09-22-10

INSULATION

CRIMP

BRUSH

STRIP

LENGTH

BELL MOUTH

CRIMP HEIGHT

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP

TWISTING

HAND CRIMP

TOOL

Application Tooling

Specification S eet Order No. 63819-2900

FEATURES

 A full cycle ratcheting hand tool ensures complete crimps

 Ergonomic soft grip handles for comfortable crimping

 A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position

 Right and Left handed applications

 This tool is IPC/WHMA A- 20 Class 2 compliant

 This tool is RoHS compliant, however RoHS compliant is not required

SCOPE

Products: Low Force Micro-Fit 3.0™ Crimp Terminals, 20-30 AWG.

Terminal Series No.

Terminal Order No. Wire Size Insulation Diameter Strip Lengt





Reel AWG

mm² mm In. mm In.

4 235

4 235-0001

4 235-0002

20-24

0.50-0.20

1.30-1.85

.051-.073

2.54-2.92

.100-.115

4 235-5001

4 235-5002

4 235-0003

4 235-0004

2 -30

0.13-0.05

1.12-1.27

.044-.050

4 235-5003

4 235-5004

Customer to cut off terminal from reel: 0.25mm (.010”) maximum Cut-off Tab.

DEFINITION OF TERMS

The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the

scope.

TYPE 4D

Hand Crimp Tool For Low Force Micro-Fit 3.0™ Crimp Terminals

Doc No: ATS- 38192900 Release Date: 12-10-08 UNCONTROLLED COPY Page 2 of 7

Revision: B Revision Date: 09-22-10

RELEASE

LOCATOR

BUTTON

TERMINAL Figure 3

LOCATOR

PUSHED THRU

TOOLING

TERMINAL

LOCATOR

BUTTON

PUSHED IN

LOCATOR

CONDITIONS:

After crimping, the conductor profiles should measure the following.

Terminal

Series No

Wire Size Conductor Crimp Insulation Crimp Pull Force

Minimum Profile

Heig t (Ref.) Widt (Ref.)

Heig t (Ref.)

Widt (Ref.)

AWG

mm2

mm In. mm In. mm In. mm In. N Lb. 22-24

26-30

4 235

20 0.50 0.7 -0.81

.030-.032

1.40 .055 1.90 .075 1.85 .073 57.9

13.00

22 0.35 0. -0.7

.02 -.030

1.15 .045 1. 5 .0 5 1. 0 .0 3 35.

8.00 X

24 0.20 0. -0.7

.02 -.030

1.15 .045 1. 5 .0 5 1. 0 .0 3 22.3

5.00 X

2 0.13 0.45-0.5

.018-.022

1.00 .039 1.35 .053 1.35 .053 13.4

3.00 X

28 0.08 0.45-0.5

.018-.022

1.00 .039 1.35 .053 1.35 .053 8.9 2.00 X

30 0.05 0.45-0.5

.018-.022

1.00 .039 1.35 .053 1.35 .053 .7 1.50 X

OPERATION

CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage can

occur to the tool or die.

Open the tool by squeezing the handles

together. At the end of the closing stroke,

the ratchet mechanism will release the

handles and the hand tool will spring open.

See Figure 1.

Crimping Terminals

1. Select the desired terminal listed in the

preceding charts.

2. Make sure the center of the locator is

in the down position. With the locator

attached, push the locator button on

the back of the hand tool to bring the

locator forward through the tooling.

See Figure 2.

SQUEEZE

HANDLES

TOGETHER

HANDLE WILL

SPRING OPEN

Figure 1

LOCATOR

IN DOWN

POSTION

PUSH ON THE

LOCATOR BUTTON

Figure 2

Hand Crimp Tool For Low Force Micro-Fit 3.0™ Crimp Terminals

Doc No: ATS- 38192900 Release Date: 12-10-08 UNCONTROLLED COPY Page 3 of 7

Revision: B Revision Date: 09-22-10

Figure 5 TERMINAL

WIRE AGAINST THE

WIRE STOP

WIRE

WIRE STOP IS PART

OF THE LOCATOR

PRE-STRIPPED

WIRE

TERMINAL

3. While holding the locator button in, load the terminal into the proper

nest opening in the locator based on the wire gauge or terminal type

markings on the hand tooling. See Figure 3.

4. Release the locator button, allowing the locator to return to the crimping

position.

5. Close the tool handle until the first ratchet position engages. See

Figure 4.

. Insert the properly stripped wire through the terminal and against the

wire stop. See Figure 5.

7. Crimp the terminal by squeezing the tool handles until the ratchet

mechanism cycle has been completed. Release the handles to open

the jaws.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

8. Remove the crimped terminal from the terminal

locator by pulling on the wire.

9. Visually inspect the crimped terminal for proper

crimp location.

10. On some large O.D. wires, it may not be possible to

insert the wire with the tool partially closed. Those

wires should be inserted with the hand tool in the

open position. Insert the wire above the terminal in

the punch and against the wire stop then close the

tool. See Figure .

Note:

A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,

insulation diameters, and durometers available, actual crimp height measurements may very slightly. An

occasional, destructive, pull force test should be performed to check hand tool crimp. Pull Force value Must exceed

the Minimum pull force specifications listed.

TERMINAL

Figure 6

WIRE

WIRE STOP

PARTIALLY

CLOSE HANDLE

TOOLING

PARTIALLY

CLOSED

Figure 4

FIRST RATCHET

POSITION

OPEN

POSITION

Hand Crimp Tool For Low Force Micro-Fit 3.0™ Crimp Terminals

Doc No: ATS- 38192900 Release Date: 12-10-08 UNCONTROLLED COPY Page 4 of 7

Revision: B Revision Date: 09-22-10

Figure 8

PUSH ON

HANDLE

JAWS OPEN

PULL OPEN

TOOLING TOOLING

M3 BHCS

MATCH

UP MARKS

FRONT BACK

Figure 9

Locator Replacement

See the parts list on the last page of this document

for the proper locator order number. Follow the

steps below to replace the locator.

1. Open the crimp hand tool.

2. Squeeze gently on the lower area shown in

Figure 7A with your thumb and index finger.

The lower tabs of the locator should disengage

from the hand tool.

3. Lift and pull away from the hand tool. The top

locator hooks should slip out of the top slots

easily. See Figure 7A.

4. To reinstall the new locator, make sure the hand

tool is in the open position.

5. Press the red insert down as far as it will go as

shown in Figure 7B.

. Holding onto the lower part of the locator with

your thumb and index finger, insert the locators top

hooks (2) into the hand tool top slots.

7. Rotate the locator down and press the lower tabs

into the two bottom slots of the hand tool. To

secure the locator into place, the lower tabs must

snap into place on the hand tool frame.

Rig t or Left Hand Operation

This hand tool has an added feature that can be

converted from a right handed application to a left

handed application. It is necessary to reverse the

tooling if using the left handed application along with

the locator. Follow the steps below:

1. The locator must be removed before reversing the

tooling.

2. Remove the M3 BHCS which is holding the upper

tooling.

3. Flip the upper tooling to the opposite side and

replace the M3 BHCS. Make sure the small

markings on the front and back of the hand tool

frame match up and are on the outside of the hand

tool frame. See Figure 8 and 9.

4. Do the same thing with the lower tooling and tighten

the M3 screws. Be sure the small markings line up.

5. Reinstall the locator by following the Instructions in

the locator replacement section.

SQUEEZE

HERE

SQUEEZE

HERE

LOCATOR

Figure 7A

TOP HOOKS

TOP SLOTS OF

HANDTOOL

LOWER TABS

MAKE SURE

CENTER OF LOCATOR

IS IN THE

DOWN POSITION

Figure 7B

Hand Crimp Tool For Low Force Micro-Fit 3.0™ Crimp Terminals

Doc No: ATS- 38192900 Release Date: 12-10-08 UNCONTROLLED COPY Page 5 of 7

Revision: B Revision Date: 09-22-10

Figure 12

SQUEEZE

THE LINK IN

THE HANDLE

HOLD THE HAND

TOOL IN POSITION

SETTING

WHEEL

RATCHET

RELEASE LEVER

Maintenance

It is recommended that each operator

of the tool be made aware of, and

responsible for, the following

maintenance steps:

1. Remove dust, moisture, and other

contaminants with a clean brush,

or soft, lint free cloth.

2. Do not use any abrasive materials

that could damage the tool.

3. Make certain all pins; pivot points

and bearing surfaces are protected

with a thin coat of high quality

machine oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it

needs cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight

automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life.

4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto

certain terminations may affect the electrical characteristics of an application.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by pressing up on the ratchet release lever in the movable handle. See

Figure 11.

How to Adjust Tool Preload (See

Figure 12)

This hand tool is factory preset to 25-45

LBS. preload. It may be necessary over

the life of the tool to adjust tool handle

preload force. Listed below are the steps

required to adjust the crimping force of the

hand tool to obtain proper crimp

conditions:

1. Hold the hand tool in the palm of your

hand as shown in Figure 12. Using

the index finger squeeze the link

towards the top of the hand tool frame.

This will release the preload

adjustment wheel.

2. Rotate the setting wheel counter-clockwise (CCW) to increase handle force. The numbers will display higher.

To decrease handle force rotate the setting wheel clockwise (CW).

3. Release the link to lock the setting wheel in place.

4. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted.

LUBRICATION POINTS

(BOTH SIDES) LIGHT OIL

(EVERY 3 MONTHS OR

5,000 CRIMPS)

Figure 10

RATCHET RELEASE

LEVER

Figure 11

Hand Crimp Tool For Low Force Micro-Fit 3.0™ Crimp Terminals

Doc No: ATS- 38192900 Release Date: 12-10-08 UNCONTROLLED COPY Page of 7

Revision: B Revision Date: 09-22-10

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will

not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,

fixturing, or use of handle extensions voids this warranty.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS:

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

Certification

Molex does not certify or re-certify hand tools but rather supplies the following guidelines for customers to re-certify

hand tools.

% This tool is qualified to pull force only. See the Molex web site for the Quality Crimp Handbook for more

information on pull testing.

% If the tool does not meet minimum pull force values, handle preload should be increased and the pull test

rerun, (See How to Adjust Preload).

% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and

replaced.

Hand Crimp Tool For Low Force Micro-Fit 3.0™ Crimp Terminals

Doc No: ATS- 38192900 Release Date: 12-10-08 UNCONTROLLED COPY Page 7 of 7

Revision: B Revision Date: 09-22-10

RATCHET

RELEASE LEVER

Figure 13

PARTS LIST

Item Number Order Number Description Quantity

REF 3819-2900 Hand Crimp Tool Figure 13

1 3819-2975 Locator Assembly 1

2 3810-0104 Spring, Return 1

3 3810-0105 Spring, Ratchet 1

http://www.molex.com

Inhaltsverzeichnis

Andere molex Crimpwerkzeuge Handbücher

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex AT 2200 Bedienungsanleitung

molex

molex 63819-0500 Benutzerhandbuch

molex

molex 63825-6070 Bedienungsanleitung

molex

molex 63827-9300 Bedienungsanleitung

molex

molex 63825-9670 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 200218-4500 Benutzerhandbuch

molex

molex 207129 Series Benutzerhandbuch

molex

molex 63811-8200 Bedienungsanleitung

molex

molex 63825-9700 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex RHT-5771 Bedienungsanleitung

molex

molex 19294-0008 Bedienungsanleitung

molex

molex 63811-1200 Bedienungsanleitung

molex

molex 59354 Bedienungsanleitung

molex

molex 63828-1900 Bedienungsanleitung

molex

molex 64001-5900 Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

Danfoss

Danfoss ET4200 Bedienungsanleitung

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung

molex 63819-2900 Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken