molex 63825-8000 Bedienungsanleitung
Hand Crimp Tool for MX120G™Crimp Terminals
Doc No. ATS-6 8258000 Release Date: 0 -22-1 UNCONTROLLED COPY Page 1 of 7
Revision: A Revision Date: 0 -22-1
INSUL CRIMP
HEIGHT
BRUSH
STRIP
LENGTH
BELL
MOUTH
COND. CRIMP
HEIGHT
BEND
DOWN
BEND UP
ROLLING
CRIMP
HEIGHT
TWISTING
CUT
-
OFF
TAB
SEAM
HAND CRIMP
TOOL
Application Toolin
Specification Sheet Order No. 63825-8000
FEATURES
A full cycle ratcheting hand tool ensures complete crimps
Ergonomic soft grip handles for comfortable crimping
A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position
Right and Left handed applications
This tool is IPC/WHMA A-620 Class 2 compliant
This tool is RoHS compliant, however RoHS compliant is not required
SCOPE
Products: 1.2mm MX120G™ Mat Seal Receptacle Terminals, 0.75mm2, 1.00mm2 wires.
Terminal
Series No.
Terminal Order No.
Wire Size
Insulation Diameter
Strip Len th
Loose Piece
Reel
Wire Type
mm² mm In. mm In.
6799 6799-0001
FLRY
-
B
0.
7
5 mm2
1.60-2.20
.06 -.087
4.50-5.50
.177-.217
FLRY
-
B
1.00
mm2
Customer to cut off terminal from reel: 0.
0mm (.0
12
”) maximum Cut
-
off Tab.
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the
scope.
TYPE 4D
Hand Crimp Tool for MX120G™Crimp Terminals
Doc No. ATS-6 8258000 Release Date: 0 -22-1 UNCONTROLLED COPY Page 2 of 7
Revision: A Revision Date: 0 -22-1
RELEASE
LOCATOR BUTTON
TERMINAL
Fi ure 3
LOCATO
R
PUSHED THRU
TOOLING
TERMINAL
LOCATOR
BUTTON
PUSHED IN
LOCATOR
CONDITIONS:
After crimping, the conductor profiles should measure the following.
Terminal
Series No
Wire Size
Conductor Crimp
I
nsulation Crimp
Pull Force
Minimum Profile
Hei ht
Width (Ref.)
Hei ht
Max.
Width
Max.
Wire Type
mm
2
mm
In.
mm
In.
mm
In.
mm
In.
N
Lb.
.75
1.0
6799
FLRY
-
B
0.75
1.10
-
1.20
.04
-
.047
1.60
.06
2. 5
.09
2. 0
.091
115
25.9
X
FLRY
-
B
1.00
1.05
-
1.15
.0
41
-
.045
2.05
.081
2.55
.100
2. 0
.091
120
27.0
X
Tool Qualification Notes:
1. Pull Force should be measured with no influence from the insulation crimp.
2. The above specifications are guidelines to an optimum crimp.
CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage can
occur to the tool or die.
Note:
A crimp height chart is provided with this manual as
Reference Only. Due to the wide range of wires,
strands, insulation diameters, and durometers
available, actual crimp height measurements may
vary slightly. An occasional, destructive, pull force
test should be performed to check hand tool crimp.
Pull Force value Must exceed the Minimum pull
force specifications listed.
OPERATION
Open the tool by squeezing the handles together.
At the end of the closing stroke, the ratchet
mechanism will release the handles and the hand
tool will spring open. See Figure 1.
Crimpin Terminals
SQUEEZE
HANDLES
TOGETHER
HANDLE WILL
SPRING OPEN
Fi ure 1
LOCATOR
IN DOWN
POSTION
PUSH ON THE
LOCATOR BUTTON
Fi ure 2
Hand Crimp Tool for MX120G™Crimp Terminals
Doc No. ATS-6 8258000 Release Date: 0 -22-1 UNCONTROLLED COPY Page of 7
Revision: A Revision Date: 0 -22-1
PRE
-
STRIPPED
WIRE
TERMINAL
Fi ure 5
TERMINAL
WIRE AGAINST
THE WIRE
STOP
WIRE
WIRE STOP IS PART
OF THE LOCATOR
1. Select the desired terminal listed in the preceding charts.
2. Make sure the center of the locator is in the down position. With the
locator attached, push the locator button on the back of the hand tool
to bring the locator forward through the tooling. See Figure 2.
. While holding the locator button in, load the terminal into the proper
nest opening in the locator based on the wire gauge or terminal type
markings on the hand tooling. See Figure .
4. Release the locator button, allowing the locator to return to the
crimping position.
5. Close the tool handle until the first ratchet position engages. See
Figure 4.
6. Insert the properly stripped wire through the terminal and against the
wire stop. See Figure 5.
7. Crimp the terminal by squeezing the tool handles until the ratchet
mechanism cycle has been completed. Release the handles to open
the jaws.
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
8. Remove the crimped terminal from the terminal
locator by pulling on the wire.
9. Visually inspect the crimped terminal for proper
crimp location.
10. On some large O.D. wires, it may not be possible
to insert the wire with the tool partially closed.
Those wires should be inserted with the hand tool
in the open position. Insert the wire above the
terminal in the punch and against the wire stop
then close the tool. See Figure 6.
Locator Replacement
See the parts list on the last page of this document for the proper locator order number. Follow the steps below to
replace the locator.
TERMINAL
Fi ure 6
WIRE
WIRE STOP
PARTIALLY
CLOSE HANDLE
TOOLING
PARTIALLY
CLOSED
Fi ure 4
FIRST RATCHET
POSITION
OPEN
POSITION
Hand Crimp Tool for MX120G™Crimp Terminals
Doc No. ATS-6 8258000 Release Date: 0 -22-1 UNCONTROLLED COPY Page 4 of 7
Revision: A Revision Date: 0 -22-1
Fi ure 8
PUSH ON
HANDLE
JAWS OPEN
PULL OPEN
TOOLING
TOOLING
M3 BHCS
MATCH
UP MARKS
FRONT
BACK
Fi ure 9
1. Open the crimp hand tool.
2. Squeeze gently on the lower area shown
in Figure 7A with your thumb and index
finger. The lower tabs of the locator
should disengage from the hand tool.
. Lift and pull away from the hand tool. The
top locator hooks should slip out of the top
slots easily. See Figure 7A.
4. To reinstall the new locator, make sure the
hand tool is in the open position.
5. Press the red insert down as far as it will
go as shown in Figure 7B.
6. Holding onto the lower part of the locator
with your thumb and index finger, insert
the locators top hooks (2) into the hand
tool top slots.
7. Rotate the locator down and press the
lower tabs into the two bottom slots of the
hand tool. To secure the locator into
place, the lower tabs must snap into place on the hand tool frame.
Ri ht or Left Hand Operation
This hand tool has an added feature that can be converted from a right handed application to a left handed
application. It is necessary to reverse the tooling if using the left handed application along with the locator. Follow
the steps below:
1. The locator must be removed before reversing the tooling.
2. Remove the M BHCS which is holding the upper tooling.
. Flip the upper tooling to the opposite side and replace the M BHCS. Make sure the small markings on the
front and back of the hand tool frame match up and are on the outside of the hand tool frame. See Figure 8
and 9.
MAKE SURE
CENTER OF LOCATOR
IS IN THE
DOWN POSITION
Fi ure 7B
SQUEEZE
HERE
SQUEEZE
HERE
LOCATOR
Fi ure 7A
TOP HOOKS
TOP SLOTS OF
HANDTOOL
LOWER TABS
Hand Crimp Tool for MX120G™Crimp Terminals
Doc No. ATS-6 8258000 Release Date: 0 -22-1 UNCONTROLLED COPY Page 5 of 7
Revision: A Revision Date: 0 -22-1
Fi ure 12
SQUEEZE
THE LINK IN
THE HANDLE
HOLD THE HAND
TOOL IN POSITION
SETTING
WHEEL
RATCHET
RELEASE LEVER
4. Do the same thing with the lower tooling and tighten the M screws. Be sure
the small markings line up.
5. Reinstall the locator by following the Instructions in the locator replacement
section.
Maintenance
It is recommended that each operator of the tool be made aware of, and
responsible for, the following maintenance steps:
1. Remove dust, moisture, and other contaminants with a clean brush, or soft,
lint free cloth.
2. Do not use any abrasive materials that could damage the tool.
. Make certain all pins; pivot points and bearing surfaces are protected with a
thin coat of high quality machine oil. Do not oil excessively. The tool was
engineered for durability but like any other equipment it needs cleaning and
lubrication for a maximum service life of trouble free crimping. Light oil (such as 0 weight automotive oil) used
at the oil points, every 5,000 crimps or months, will significantly enhance the tool life.
4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto
certain terminations may affect the electrical characteristics of an application.
5. When tool is not in use, keep the handles closed to prevent objects from
becoming lodged in the crimping dies, and store the tool in a clean, dry
area.
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed position,
Do Not force the handles open or closed. The tool will open easily by
pressing up on the ratchet release lever in the movable handle. See Figure
11
How to Adjust Tool Preload (See Fi ure 11)
This hand tool is factory preset to 25-45
LBS. preload. It may be necessary over
the life of the tool to adjust tool handle
preload force. Listed below are the steps
required to adjust the crimping force of the
hand tool to obtain proper crimp
conditions:
1. Hold the hand tool in the palm of your
hand as shown in Figure 12. Using
the index finger squeeze the link
towards the top of the hand tool
frame. This will release the preload
adjustment wheel.
LUBRICATION POINTS
(BOTH SIDES) LIGHT OIL
(EVERY 3 MONTHS OR
5,000 CRIMPS)
Fi ure 10
RATCHET RELEASE
LEVER
Fi ure 11
Hand Crimp Tool for MX120G™Crimp Terminals
Doc No. ATS-6 8258000 Release Date: 0 -22-1 UNCONTROLLED COPY Page 6 of 7
Revision: A Revision Date: 0 -22-1
2. Rotate the setting wheel counter-clockwise (CCW) to increase handle force. The numbers will display higher.
To decrease handle force rotate the setting wheel clockwise (CW).
. Release the link to lock the setting wheel in place.
4. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted.
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital
components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 0
days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will
not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,
fixturing, or use of handle extensions voids this warranty.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
CAUTIONS:
1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for
production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
. Wear eye protection at all times.
4. Use only the Molex terminals specified for crimping with this tool.
Certification
Molex does not certify or re-certify hand tools but rather supplies the following guidelines for customers to re-certify
hand tools.
% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped
12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than
25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull
testing.
% If the tool does not meet minimum pull force values, handle preload should be increased and the pull test
rerun, (See How to Adjust Preload).
% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and
replaced.
Hand Crimp Tool for MX120G™Crimp Terminals
Doc No. ATS-6 8258000 Release Date: 0 -22-1 UNCONTROLLED COPY Page 7 of 7
Revision: A Revision Date: 0 -22-1
RATCHET
RELEASE LEVER
2
Fi ure 13
1
3
PARTS LIST
Item Number
Order Number
Description
Quantity
REF
6 8
25
-
80
00
Hand Crimp Tool
Figure
1
1
6 8
25
-
80
75
Locator Assembly
1
2
6 810
-
0104
Spring, R
eturn
1
6 810
-
0105
Spring, Ratchet
1
Visit our Web site at http://www.molex.com
Inhaltsverzeichnis
Andere molex Crimpwerkzeuge Handbücher
molex
molex 78172 Series Bedienungsanleitung
molex
molex 35745 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63823-5570 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 44262-4306 Bedienungsanleitung
molex
molex RHT 2251-CC Bedienungsanleitung
molex
molex 63811-8300 Bedienungsanleitung
molex
molex PremiumGrade Series Bedienungsanleitung
molex
molex 63828-0600 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 35745 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63825-9400 Benutzerhandbuch
molex
molex 63827-1170 Bedienungsanleitung
molex
molex 63823-7570 Bedienungsanleitung
Beliebte Crimpwerkzeuge Handbücher anderer Marken
Panduit
Panduit CT-1000 Administratorhandbuch
JST
JST CS 10 Bedienungsanleitung
Danfoss
Danfoss ET4200 Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
TE Connectivity
TE Connectivity 2063528-1 Bedienungsanleitung
Tyco Electronics
Tyco Electronics 69156-1 Bedienungsanleitung
Textron
Textron ESG105L Bedienungsanleitung
Tyco Electronics
Tyco Electronics 90035-3 Bedienungsanleitung
Emerson
Emerson Klauke ES 20RMCCFB Bedienungsanleitung
Continental Refrigerator
Continental Refrigerator PC150HD Bedienungsanleitung
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung