Molex 64001-7400 Bedienungsanleitung

64001-7400 Hand Crimp Tool

Doc No. ATS-640017400 Release Date: 05-21-07 UNCONTROLLED COPY Page 1 of 8

Revision: A Revision Date: 05-21-07

Hand Crimp Tool

Operating Instruction and Specifications Sheet

Order No. 64001-7400

(Replaces 64001-3200)

FEATURES



A full cycle ratcheting hand tool ensures complete crimps



Long handles for comfortable crimping with reduced crimping force



3-nested tool eliminates the need for additional tools



A precision user-friendly terminal locator holds terminals in the proper crimping position for each of the three nests

SCOPE

Products: Perma-SealRing Tongue, Spade Tongue, Hook Tongue, 3 and 4-Way Terminals. Butt Splices and Step Down Butt Splices

10–22 AWG.

Testing

Mechanical

The tensile test, or pull test, is a means of evaluating the mechanical properties of the crimped connections. The following charts

show the specifications for various wire sizes. The tensile strength is shown in pounds and indicates the minimum acceptable force

to break or separate terminal from the conductor.

Wire Size (AWG) UL – 486 A UL – 486 C

22 8 8

20 13 10

18 20 10

16 30 15

14 50 25

12 70 35

10 80 40

*UL - 486 A - Terminals (copper conductors only)

*UL - 486 C - Butt Splices, Parallel Splices

The following is a partial list of the product part numbers and their specifications that this tool is designed to run. We will be adding to

this list and an up to date copy is available on www.molex.com

Wire Size: 18 – 22 AWG 0.80 – 0.35 mm²

Wire Strip Length Insulation Diameter

Maximum

Terminal No. Terminal

Eng No. (REF)

Terminal No.

Mylar Tape In mm In mm

19164-0003 SA-221-10 19164-0306 .281 7.14 .235 5.97

19164-0004 SA-222-14 19164-0844 .281 7.14 .235 5.97

19164-0005 SA-226-38 19164-0845 .281 7.14 .235 5.97

19164-0006 SA-235-06 .281 7.14 .235 5.97

19164-0007 SA-235-08 .281 7.14 .235 5.97

19164-0008 SA-235-10 .281 7.14 .235 5.97

19164-0011 SA-2YCX N/A .281 7.14 .215 5.46

19164-0013 SAA-22-18 19164-0014 .281 7.14 .210 5.33

64001-7400 Hand Crimp Tool

Doc No. ATS-640017400 Release Date: 05-21-07 UNCONTROLLED COPY Page 2 of 8

Revision: A Revision Date: 05-21-07

Wire Size: 18 – 22 AWG 0.80 –0.35 mm²

Wire Strip Length Insulation Diameter

Maximum

Terminal No. Terminal

Eng No. (REF)

Terminal No.

Mylar Tape In mm In mm

19164-0085 SA-221-06 .281 7.14 .235 5.97

19164-0086 SA-221-08 19164-0419 .281 7.14 .235 5.97

19164-0210 SA-210-06 .281 7.14 .235 5.97

19164-0211 SA-210-08 .281 7.14 .235 5.97

19164-0212 SA-210-10 .281 7.14 .235 5.97

19164-0283 SA-232-04 .281 7.14 .235 5.97

19164-0284 SA-2XCX N/A .281 7.14 .235 5.97

19164-0435 SA-222-56 .281 7.14 .235 5.97

19164-0443 SA-215-08 19164-0850 .281 7.14 .235 5.97

19164-0445 SA-215-04 .281 7.14 .235 5.97

19164-0446 SA-215-06 .281 7.14 .235 5.97

19164-0625 SA-222-10 .281 7.14 .235 5.97

Wire Size: 14 –16 AWG 2.00 –1.30 mm²

Wire Strip Length Insulation Diameter

Maximum

Terminal No. Terminal

Eng No. (REF)

Terminal No.

Mylar Tape In mm In mm

19164-0020 SB-218-38 19164-0307 .281 7.14 .235 5.97

19164-0021 SB-219-10 .281 7.14 .235 5.97

19164-0022 SB-223-06 .281 7.14 .235 5.97

19164-0023 SB-224-06 .281 7.14 .235 5.97

19164-0024 SB-224-08 .281 7.14 .235 5.97

19164-0025 SB-225-10 19164-0940 .281 7.14 .235 5.97

19164-0026 SB-225-14 19164-0308 .281 7.14 .235 5.97

19164-0027 SB-225-56 19164-0309 .281 7.14 .235 5.97

19164-0028 SB-227-06 19164-0948 .281 7.14 .235 5.97

19164-0029 SB-227-08 19164-0949 .281 7.14 .235 5.97

19164-0030 SB-227-10 19164-0950 .281 7.14 .235 5.97

19164-0031 SB-237-04 19164-0941 .281 7.14 .235 5.97

19164-0032 SB-237-06 19164-0310 .281 7.14 .235 5.97

19164-0033 SB-237-08 19164-0311 .281 7.14 .235 5.97

19164-0034 SB-237-10 19164-0312 .281 7.14 .235 5.97

19164-0035 SB-239-04 .281 7.14 .235 5.97

19164-0036 SB-239-06 .281 7.14 .235 5.97

19164-0037 SB-239-08 .281 7.14 .235 5.97

19164-0038 SB-239-10 19164-0313 .281 7.14 .235 5.97

19164-0041 SB-2XCX N/A .281 7.14 .235 5.97

19164-0042 SB-2YCX N/A .281 7.14 .235 5.97

19164-0044 SBB-16-14 19164-0045 .375 9.53 .200 5.08

19164-0139 SB-218-56 .281 7.14 .235 5.97

19164-0141 SB-219-06 .281 7.14 .235 5.97

19164-0142 SB-219-08 .281 7.14 .235 5.97

19164-0146 SB-618-38 .281 7.14 .235 5.97

19164-0150 SB-319-10 .281 7.14 .235 5.97

19164-0152 SB-625-14 .281 7.14 .235 5.97

19164-0153 SB-625-56 .281 7.14 .235 5.97

19164-0154 SB-327-06 .281 7.14 .235 5.97

19164-0155 SB-327-08 .281 7.14 .235 5.97

19164-0156 SB-327-10 .281 7.14 .235 5.97

19164-0159 SB-637-06 .281 7.14 .235 5.97

64001-7400 Hand Crimp Tool

Doc No. ATS-640017400 Release Date: 05-21-07 UNCONTROLLED COPY Page 3 of 8

Revision: A Revision Date: 05-21-07

Wire Size: 14 –16 AWG 2.00 –1.30 mm²

Wire Strip Length Insulation Diameter

Maximum

Terminal No. Terminal

Eng No. (REF)

Terminal No.

Mylar Tape In mm In mm

19164-0160 SB-637-08 .281 7.14 .235 5.97

19164-0161 SB-637-10 .281 7.14 .235 5.97

19164-0532 SB-216-08 .281 7.14 .235 5.97

19164-0849 SB-216-10 .281 7.14 .235 5.97

Wire Strip Length Insulation Diameter

Maximum

Terminal No. Terminal

Eng No. (REF)

Terminal No.

Mylar Tape In mm In mm

19164-0056 SC-12-10 19164-0057 .375 9.53 .280 7.11

19164-0058 SC-201-12 .438 11.12 .310 7.87

19164-0060 SC-228-04 19164-0936 .438 11.12 .310 7.87

19164-0061 SC-228-06 19164-0937 .438 11.12 .310 7.87

19164-0062 SC-228-08 19164-0938 .438 11.12 .310 7.87

19164-0063 SC-228-10 19164-0939 .438 11.12 .310 7.87

19164-0065 SC-230-10 19164-0316 .438 11.12 .310 7.87

19164-0066 SC-230-14 19164-0317 .438 11.12 .310 7.87

19164-0067 SC-230-56 19164-0318 .438 11.12 .310 7.87

19164-0068 SC-240-38 19164-0857 .438 11.12 .310 7.87

19164-0069 SC-241-06 .438 11.12 .310 7.87

19164-0070 SC-241-08 .438 11.12 .310 7.87

19164-0071 SC-241-10 .438 11.12 .310 7.87

19164-0072 SC-268-10 .438 11.12 .310 7.87

19164-0073 SC-268-14 .438 11.12 .310 7.87

19164-0074 SC-2YCX N/A .438 11.12 .310 7.87

19164-0200 SC-301-12 .438 11.12 .310 7.87

19164-0201 SC-328-06 .438 11.12 .310 7.87

19164-0202 SC-328-08 .438 11.12 .310 7.87

19164-0203 SC-328-10 .438 11.12 .310 7.87

19164-0204 SC-330-14 .438 11.12 .310 7.87

19164-0205 SC-330-56 .438 11.12 .310 7.87

19164-0206 SC-340-38 .438 11.12 .310 7.87

19164-0207 SC-341-06 .438 11.12 .310 7.87

19164-0208 SC-341-08 .438 11.12 .310 7.87

19164-0209 SC-341-10 .438 11.12 .310 7.87

19164-0213 SC-211-06 .438 11.12 .310 7.87

19164-0214 SC-211-08 .438 11.12 .310 7.87

19164-0215 SC-211-10 .438 11.12 .310 7.87

19164-0285 SC-2XCX N/A .438 11.12 .310 7.87

19164-0533 SC-217-08 .438 11.12 .310 7.87

19164-0534 SC-217-10 .438 11.12 .310 7.87

19164-0624 SC-236-08 .438 11.12 .310 7.87

19164-0846 SC-201-38 .438 11.12 .310 7.87

64001-7400 Hand Crimp Tool

Doc No. ATS-640017400 Release Date: 05-21-07 UNCONTROLLED COPY Page 4 of 8

Revision: A Revision Date: 05-21-07

TERMINAL

AGAINST

LOCATOR

TOOL

OPEN

Figure 1

PUSH IN

LOCATOR

CLAMP

Figure 2

TO ADJUST

SLIDE LOCATOR

LOCATOR

KNOB

LOCATOR

CLAMP DOWN TERMINAL

IN POSITION

STEP DOWN BUTT SPLICE

Wire Size: 14 –16 AWG 2.00 –1.30mm²to

18 - 22 AWG .080-0.35 mm²

Wire Strip Length Insulation Diameter

Maximum

Terminal No. Terminal

Eng No. (REF)

Terminal No.

Mylar Tape In mm In mm

19164-0043 SBA-631 .281 7.14 .230 5.84

STEP DOWN BUTT SPLICE

Wire Size: 10 –12 AWG 5.00 –3.30mm²to

14 - 16 AWG 2.00-1.30 mm²

Wire Strip Length Insulation Diameter

Maximum

Terminal No. Terminal

Eng No. (REF)

Terminal No.

Mylar Tape In mm In mm

19164-0077 SCB-646 19164-0582 .281 7.14 .300 7.62

OPERATION

Open the tool by first closing the jaws sufficiently for the ratchet mechanism to release.

Crimping Terminals

1. Push in on the locator clamp to lift and position the nose of terminal under the clamp and push against the shoulder with the

barrel facing up into the color-coded nest. Release the locator clamp to hold the terminal. See Figure 1.

2. Loosen the locator knob and slide as required until the conductor barrel is centered over the crimp pocket in the lower jaw as

shown in Figure 2. Tighten the locator knob to lock the locator assembly in position.

3. Partially close the hand tool jaws until the terminal is held snug in place.

64001-7400 Hand Crimp Tool

Doc No. ATS-640017400 Release Date: 05-21-07 UNCONTROLLED COPY Page 5 of 8

Revision: A Revision Date: 05-21-07

WIRE

TERMINAL Figure 3 Figure 4

TERMINAL

BARREL

CONDUCTOR ANVIL

TERMINAL

CONDUCTOR

PUNCH

LOCATOR WIRE

4. Insert the properly stripped wire into the terminal barrel. See Figure 3 and 4.

5. Complete the crimp by closing the hand tool handles until they release.

6. Remove the crimped terminal by pulling away from the locator or open to remove flanged spades. Inspect for proper crimp

location. Molex offers a Crimp Inspection Handbook for closed barrel industrial product. See our website or contact your Molex

sales engineer.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

Crimping Butt Splices

When crimping one end of a butt splice, loosen the locator

knob and slide locator all the way out away from crimp

jaws. When crimping the second end of a butt splice the

locator assembly must be removed. See Figure 5.

1. Position the butt splice centered over the appropriate

crimp pocket.

2. Partially close the tool to hold the butt splice in place.

3. Insert the properly stripped wire into the butt splice.

The end of the wire should butt against the wire stop

in the butt splice. Cycle the tool.

4. Remove the crimped butt splice and inspect for proper

crimp location.

5. To crimp the second end, remove the locator assembly and rotate the butt splice 180°so the opposite end of the butt splice is

centered over the appropriate crimp pocket.

6. Repeat steps. 2 thru 4.

Note: Whenever crimping without the locator, make sure the seam of the terminal is oriented up or down in the tool if using

unbrazed product, as this will provide higher pull force values.

Figure

5 CONDUCTOR ANVIL

CONDUCTOR

PUNCH

TERMINAL

WIRE STOP

BUTT SPLICE

TERMINAL

SLIDE LOCATOR AWAY

FROM THE TERMINAL WIRE

64001-7400 Hand Crimp Tool

Doc No. ATS-640017400 Release Date: 05-21-07 UNCONTROLLED COPY Page 6 of 8

Revision: A Revision Date: 05-21-07

Maintenance

It is recommended that each operator of the tool be made aware of, and

responsible for, the following maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean brush, or soft,

lint free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a

thin coat of high quality machine oil. Do not oil excessively. This hand tool

was engineered for durability but like any fine piece of equipment, it requires

cleaning and lubrication for maximum service life of trouble free operation.

Use light oil such as 30 weight automotive at the oil points shown in Figure 5. Lubricate every 5,000 crimps or 3 months to

significantly enhance the tool life.

4. When tool is not in use keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in a

clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed.

The tool will open easily by turning the ratchet release screw. See Figure 7.

Tool Calibration

A Certificate of Calibration (see last page) was supplied with the tool. To verify calibration of this tool, pin gauge measurements should

be taken in each conductor nest and compared to this chart. The tool should be lubricated before checking calibration to ensure

consistent measurements. Handle preload is factory set to 25-45 LBS.

Wire Range “X”Dimension Conductor Crimp

Nest Color Code AWG mm²Mean Go No Go Crimp Inspection Marking

Red 18 - 22 0.35 - 0.80 .094 .090 .098 ---

Blue 14 - 16 1.30 - 2.00 .115 .110 .119 ---

Yellow 10 - 12 3.30 - 5.00 .161 .156 .167 ---

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long

life-tested. All tools are warranted free of manufacturing defects for a period of 30 days. Should such a defect occur, we will repair

or exchange the tool free of charge. This repair or exchange will not be applicable to alter, misused, or damaged tools. This tool is

designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty.

Hand held crimping tools are intended for low volume, prototyping, or repair requirements only.

Caution: Repetitive use of this tool should be avoided.

LUBRICATION POINTS

(BOTH SIDES)

LIGHT OIL (EVERY 3 MONTHS

OR 5,000 CRIMPS)

Figure 6

64001-7400 Hand Crimp Tool

Doc No. ATS-640017400 Release Date: 05-21-07 UNCONTROLLED COPY Page 7 of 8

Revision: A Revision Date: 05-21-07

PARTS LIST

Item Number Order Number Description Quantity

64001-7400 Hand Crimp Tool Figure 7

1 64001-7475 Locator Assembly 1

Figure 7

RATCHET

RELEASE SCREW

M4 X 30mm SHCS

64001-7400 Hand Crimp Tool

Doc No. ATS-640017400 Release Date: 05-21-07 UNCONTROLLED COPY Page 8 of 8

Revision: A Revision Date: 05-21-07

Certificate of Calibration

Tool Order Number __64001-7400____________

Tool Eng. Number ___64001-7400____________

Tool Revision ___________A______________

Serial Number_________________________

Date of Manufacture_____________________

Pin Gage of Conductor Nest/Nests or Slug height if the nest is the “F”Crimp style.

Range Conductor Nest # 1 =__.090/.097____Actual =_____________

Range Conductor Nest # 2 =__.110/.118____Actual =_____________

Range Conductor Nest # 3 =__.156/.166____Actual =_____________

Technician________________________

Date of Calibration ___________________

Americas Headquarters

-JTMF*MMJOPJT64"

.0-&9

BNFSJOGP!NPMFYDPN

Far East North Headquarters

:BNBUP,BOBHBXB+BQBO



GFOJOGP!NPMFYDPN

Far East South Headquarters

+VSPOH4JOHBQPSF



GFTJOGP!NPMFYDPN

European Headquarters

.VOJDI(FSNBOZ



FVSJOGP!NPMFYDPN

Corporate Headquarters

8FMMJOHUPO$U

-JTMF*-64"



'BY

Visit our Web site at http://www.molex.com

Andere Handbücher für 64001-7400

Inhaltsverzeichnis

Andere molex Crimpwerkzeuge Handbücher

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63823-8000 Bedienungsanleitung

molex

molex 63819-0600 Bedienungsanleitung

molex

molex 63827-0470 Bedienungsanleitung

molex

molex 63825-4970 Bedienungsanleitung

molex

molex RHT-5771 Bedienungsanleitung

molex

molex ServiceGrade 64016-0036 Benutzerhandbuch

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63825-6070 Bedienungsanleitung

molex

molex CR1031E Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 63811-5800 Bedienungsanleitung

molex

molex 78172 Series Bedienungsanleitung

molex

molex 63825-9670 Bedienungsanleitung

molex

molex PremiumGrade 63827-1700 Bedienungsanleitung

molex

molex 63811-7200 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 35465 Series Bedienungsanleitung

molex

molex AT-200 Bedienungsanleitung

molex

molex 207129 Series Bedienungsanleitung

molex

molex 200218-4500 Benutzerhandbuch

Beliebte Crimpwerkzeuge Handbücher anderer Marken

Panduit

Panduit CT-1000 Administratorhandbuch

JST

JST CS 10 Bedienungsanleitung

TE Connectivity

TE Connectivity 2063528-1 Bedienungsanleitung

Tyco Electronics

Tyco Electronics 69156-1 Bedienungsanleitung

CRH

CRH CRL CBLHCT1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFM Bedienungsanleitung

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Bedienungsanleitung

Danfoss

Danfoss ET4350 Bedienungsanleitung

Milwaukee

Milwaukee M18 Bedienungsanleitung

HOGERT

HOGERT HT1P169 Bedienungsanleitung

Textron

Textron ESG105L Bedienungsanleitung

Tyco Electronics

Tyco Electronics 90035-3 Bedienungsanleitung

Emerson

Emerson Klauke ES 20RMCCFB Bedienungsanleitung

Continental Refrigerator

Continental Refrigerator PC150HD Bedienungsanleitung

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung

Emerson

Emerson Klauke ES 105CFB Bedienungsanleitung

TE Connectivity

TE Connectivity 539 726-2 Bedienungsanleitung

molex 64001-7400 Bedienungsanleitung

Beliebte Crimpwerkzeuge Handbücher anderer Marken