Monte Carlo Fan Company 3LR38 Series Bedienungsanleitung

Owner’s

anual

Ceiling Fan Installation Instructions

57 &&!,70,8(4

!$"!!" #"!

Total fan weight

with lights

Shown With 38” blades

UL odel No. : 3LR38/22

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999),

including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and

pushed carefully up into the outlet box.

Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

ake sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to

the trailing edge of the blade.

% : To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

( ounting must support at least 35 lbs.)

% : To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert for-

eign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

% : To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment man-

ufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

#"To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

10.

11.

12.

13.

14.

15.

16.

Installation

% " #" ! " ! # '" !!

! $"% !$"!!" #"!

!"' "!

"! # 

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.



Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support.

( ounting must support at least 35 lbs.)



Use metal outlet box suitable for fan support and

:8,542>9/,8*7,<8675;0+,+<09/9/,5:92,9

)5=(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet box is securely fas-

tened by at least two points to a structural ceiling

member ( a loose box will cause the fan to wob-

ble). Remove the two outlet box screws provided

with the box, aligning the holes of the mounting

bracket with the holes of the outlet box. Re-install

the 2 outlet box screws securely.





Remove cotter pin from downrod, and

save for later use.



Place canopy over downrod.



Loosen the 2 screws on the yoke to

allow down rod to slip into yoke.

Place yoke cover over downrod.



Thread the leadwires and safety

cable through the downrod.



Insert downrod into the yoke on top

of fan body. Align the hole in the

downrod with the hole in the yoke.

Insert cotter pin through yoke and

downrod until point appears on the

other side

ake sure the studs protruding from the

bottom of the ounting bracket are

installed with threads all the way through

the bracket.



Tighten the 2 set screws on the

yoke, once the down rod is in place.



Hang assembled fan from the mounting bracket

installed to ceiling in previous step. ake sure the

fan is hanging straight. Rotate fan until the tab on

the ounting bracket engages the slot on the

Downrod Ball. This must be done to prevent the fan

body from rotating when the blades are in motion.



Install keeper pin.



Fan and light kit combinations over 35 lbs,

in both flush and downrod mode the safety

cable must be installed into the house struc-

ture beams using the 3” lag screws,washers,

and lock washers. provided. ake sure that

when the safety cable is fully extended the

lead wires are longer than the cable and no

stress is placed on the lead wires.

 Safety cable installation

!(-,9>()2,

(.!*7,<

safety

cable

3” lag

screw

lock

washer

Connect black and blue wire from fan to Black or (Hot)

wire from house. Connect White wire from Fan to

White (Neutral) wire from house. Connect Ground

leads from mounting bracket and downrod to Ground

lead from house. ,-,795!(-,9>"0688,*90545-

3(4:(2



ake wire connections to power source using wire nuts

provided. ake sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on

the other side of the outlet box. The splices after being

made should be turned upward and pushed carefully

up into the outlet box.



Lift canopy and install knurled nuts as

shown. Tighten the knurled nuts securely.

The canopy should adjust for any irregu-

larity in the ceiling or Outlet box.



Check for shipping stabilizers and remove

if present. Attach blades using screws in

hardware pack. /58,)2(+,80?,>5:

201, Tighten screws securely. Repeat 2

more times.



Connect white wire from fan to White

wire from light fixture. Connect blue

wire from fan to Black wire from light

fixture.



Loosen 2 screws and remove one

screw. Keep removed screw for

later use.



Align keyslot holes of light kit

plate and twist it to lock clock-

wise. Install the screw removed

in step 19 and tighten all screws

securely.



Attach blanking plate by locating

dimples in light fixture with grooves

in the blanking plate and twist clock-

wise.



57-(4<09/5:9

20./9109.595

89,6

57-(4<09/

20./9109.595

89,6

Install 75 watt halogen bulb. Bulb

included. Do not touch bulb surface

as oily residue from skin can cause

the bulb to explode. % :

Over lamping the fan will result in the

fan lights shutting down until the

proper wattage bulbs are installed.

Reset lights by turning off the wall

switch, breaker, or by remote.

Replace with correct wattage bulbs,

turn the power on.



Attach the glass by locating dimples

in light fixture with groves in the

glass and twist clockwise until tight.



Align keyslot holes of light kit plate

and twist it to lock clockwise. Install

screw removed in step 22 and tighten

all screws securely.



Lossen 2 screws and remove one

screw. Keep removed screw for later

use.



Connect the plug from fan to the

plug from light kit plate.



Customer Service Center:

301 West Washington St.

Riverside, NJ 08075

1-800-519-4092

www.montecarlofans.com

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3. ake sure forward/reverse switch is firmly in up or down position. Fan will not operate when

switch is in the middle.

#"(1,8:7,3(0465<,7089:74,+5--

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

#"(1,8:7,3(0465<,7089:74,+5--),-57,,49,704.8<09*//5:804.

4.Some fan motors are sensitive to signals from Solid State variable speed controls. "#!

(!520+!9(9,;(70()2,86,,+*549752

5.Allow "break-in" period of 24 hours. ost noises associated with a new fan will disappear after

this period.

1. ake sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4. ake sure that canopy and mounting bracket are tightened securely to ceiling junction box and

junction box is mounted firmly to ceiling joist.

5. ost fan wobble problems are caused when blade levels are unequal. Check this level by selecting

a point on the ceiling above the tip of one of the blades. easure this distance from blade tip to

ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-

ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the fol-

lowing procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and

blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not supplied)

between the blade and blade holder at the two screws farthest from the motor. Reverse the posi-

tion of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistrib-

ute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

%  ;,72(3604.9/,-(4<0227,8:29049/,-(420./988/:9904.+5<4:4902

9/,6756,7<(99(.,5-):2)8(7,0489(22,+

,8,99/,20./98)>9:7404.5--9/,<(228<09*/)7,(1,757)>7,359, ,62(*,):2)8<09/

9/,*577,*9<(99(.,):2)89:749/,65<,754

#"(1,8:7,3(0465<,7089:74,+5--),-57,,49,704.8<09*//5:804.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble

Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our

Customer Service Center at the

number printed on your parts list insert sheet.

%(7404.,-57,8,7;0*04.57*2,(404.:409!<09*/65<,75--(9!,7;0*,6(4,2(4+25*18,7;0*,+08*544,*904.

3,(489567,;,4965<,7-753),04.8<09*/,+54(**0+,49(22>%/,49/,8,7;0*,+08*544,*904.3,(48*(4459

),25*1,+8,*:7,2>-(89,4(

675304,49<(7404.+,;0*,8:*/(8(9(.959/,8,7;0*,6(4,2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3MGMR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Jovie 3JVR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MX series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ARR58XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LLR56 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TQ52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Loft 72 6LFR72 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GMR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CO52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GIR54XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CY60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VER56XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3STR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VL52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLNSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42RB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SY52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ERHR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company BF1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LNR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CLR66XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GL66 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52ES D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3KNR52XXD Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung