Monte Carlo Fan Company 5MX series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attac sales receipt to t is card and retain as your proof of purc ase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To register your fixture, please visit our website www.montecarlofans.com

5MX Series Fan

Total fan weig t

UL Model No. : AC-212-001

11.71 kgs

25.76 lbs

WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G

READ A D SAVE THESE I STRUCTIO S

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA

70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

31.8 kg (70 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

ever place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Cutomer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Insert downrod into motor yoke. Next, insert

clevis pin through yoke and downrod and secure

with cotter pin. (see inset)

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting

means to prevent power from being switched on ac-

cidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warn-

ing device, such as a tag, to the service panel.

Install canopy and yoke cover over the downrod.

Thread wire through downrod with canopy and

yoke cover assembled.

Outlet box

Wood

Screws

Mounting

Bracket

Secure mounting bracket directly to a joist from

the buliding structure via the two knock out

holes on the outlet box. Use only the appropriate

wood screws and washers included with your

fan. Caution: Wood screws must go through into

the building joist.

Warning-Risk of fire, electric shock, or personal

injury. The fan in this box may be either directly

supported from a structural framing member of

a building and/or may be mounted to an outlet

box marked acceptable for fan support of of

31.8 kg (70 lbs) or less. Most outlet boxes com-

monly used for the support of lumminaires may

not be acceptable for fan support and may need

to be replaced. Consult a qualified electrician if

in doubt.

2OUTLET BOX METHOD BUILDING

STRUCTURE

METHOD

Carefully lift fan assembly onto mounting

bracket. Rotate fan so that the notch on the ball

engages the ridge in the mounting bracket. This

will allow hands-free wiring.

For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be in-

stalled into the house structure beams using the

3” lag screws provided. Make sure that when

the safety cable is fully extended the leadwires

are longer than the cable and no stress is placed

on the leadwires.

9Safety cable installation

Safety Ca le

Lag Screw

Tighten both yoke set screws to further secure

downrod.

lace blade onto blade holder.

Install 3 screws and washers per blade and

tighten securely. Repeat for all 5 blades

Make wire connections to power source using

wire nuts provided. Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on the

other side of the outlet box.

For control of fan and optional light from wall lo-

cation, follow diagram above. NOTE: A profes-

sional electrician is recommended for this type

of installation.

Raise the canopy up and align the two holes in

the canopy with the two holes in the hanger

bracket. Secure with two screws provided.

Light Switch

Fan Switch

Wall

Control

Check the motor for plastic shipping stabilizer

tabs, and remove them if they are present. At-

tach blade assembly to motor using the motor

screws and washers provided. Tighten screws

securely.

Remove 1 screw and save.Loosen other 2

screws.

ush wires through center hole.Line up 2 screws

loosened from step 17.

Remove

and save

screws

For pullchain controls, follow diagram above.

Make sure that all exposed wiring is secured

inside wire nuts. Note: Wires from house may

vary in color and may not include ground

wire. After wiring is conplete, gently push

wires into junction box with wire nuts pointing

upward. Refer to point 3 of safety tips.

11 House Fan

Blue

Black

White

Green(Downrod)

Black

White

Green/

Ground

Green(Bracket)

Reinstall the switch housing using the three

screws previously removed.

Twist into locking position and tighten in screw

taken out. Also tighten 2 other loosened screws.

Connect male to female connector securely.

Remove 3 screws and save.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Make sure forward/reverse switch is pushed firmly either way. Fan will not operate when

switch is in the middle.

CAUTION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are

tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off efore entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls. DO

NOT USE a Solid State varia le speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disap-

pear after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction

box and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level

by selecting a point on the ceiling above the tip of one of the blades. Measure this dis-

tance from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next

blade is positioned for measurement. Repeat for each blade. If all blade levels are not

equal, you can adjust blade levels by the following procedure. To adjust a blade tip down,

insert a washer (not supplied) between the blade and blade holder at the screw closest to

the motor. To adjust a blade tip up, insert washer (not supplied) between the blade and

blade holder at the two screws farthest from the motor. Reverse the position of the

washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off efore entering switch housing.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installa-

tion, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience

any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experi-

encing difficulty in installation, please call our Customer Service Center at the number printed on your

parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service

disconnecting means to prevent power from eing switched on accidentally. When the service

disconnecting means cannot e locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Trou le Suggested Remedy

Jan.2012 New format

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3VLR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MO52 O-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SU54BK Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DSTR57 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CLR66XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLMR56XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSR60AGD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LNR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Jovie 3JOVR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5vsr44XXd-l series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3OBSHR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OBR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LWDSM60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4SBWR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CO52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSR60AGD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MTR38TMO-L Handbuch

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Arcade 3ARR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MMR54 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Hicks 3HCKR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MX Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung