Monte Carlo Fan Company 5GMR52XXD Series Bedienungsanleitung

Quality Ceiling fans

Owner’s

Manual

Ceiling Fan Installation Instructions

For 5GMR52XXD Series Fans

READ AND SAVE THESE INSTRUCTIONS

Total fan weigh

with light

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-

1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

(Mounting must support at least 35 lbs. (16kg.)).

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equip-

ment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

10.

11.

12.

13.

14.

15.

Installation

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

SAFETY TIPS

TTOOOOLLSSRREEQQUUIIRREEDD

PPhhiilllliippssSSccrreewwddrriivveerrWWiirreeCCuutttteerrssPPlliieerrssSStteeppLLaaddddeerr

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Loosen lock nuts and screws on yoke

till you can not feel screw on inside

of yoke.

Remove keeper from cross pin and

then cross pin from yoke. Replace

keeper on cross pin and save.

Slide canopy and yoke cover on

downrod. Thread lead wires and

safety cable through downrod as

shown.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support. (Mounting

must support at least 35 lbs.(16 kg.)).

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet box is securely

fastened by at least two points to a structural

ceiling member ( a loose box will cause the fan

to wobble). Use only the screws pro-

vided with the outlet box.

Raise fan with downrod assembled to

the ceiling bracket and hang fan

assembly. Be sure to rotate the

downrod ball so that the notch in the

bracket engages the slot in the ball.

Install 4 x 25 watt candelabra base

bulbs included.

10 12

Place upper glass over downrod and

canopy onto the fan body.

Align hole in downrod with hole in

yoke and install cross pin. Install

downrod into yoke. Install keeper

into cross pin.

Tighten 2 downrod set screws and

lock nuts.

Set dip switches on the Remote Transmitter and Remote

Receiver to the same settings. This must be done so the

units will communcate properly. If you have other fans you

can set to control from one transmitter by setting both

receivers the same as the transmitter. If you have more

than one fan with remote. You can set the dip switches to

different positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches

Make wire connections to power source using

wire nuts provided. Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on

the other side of the outlet box.

Lift canopy to ceiling aligning the key hole slots

with the screws on the bottom of the mounting

bracket. Rotate the canopy counter clockwise

to lock in place. Tighten the screws to secure

the canopy. See inset for keyhole shape

Install remote receiver by sliding into opening in

the Mounting bracket. Make sure that the dip

switches on the Transmitter and the Receiver

are set to the same position. See Fig 31 for

remote operation

Attach blade arms to blades using

the blade arm screws and washers

provided.

white

black

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Orange from fan to Orange from remote

marked Light/up. Blue from fan to blue from

remote marked down light. Black from fan to

Black from remote marked L. White from

house to white from remote marked AC N .

Black from house to Black from remote

marked AC L. Connect all green ground wires

to Ground wire from House.

orange

blue Green

white

black

House

Fan

fuses

Fan and light kit combinations over 35 lbs,

in both flush and downrod mode the safety

cable must be installed into the house struc-

ture beams using the 3” lag screws,washers,

and lock washers. provided. Make sure that

when the safety cable is fully extended the

lead wires are longer than the cable and no

stress is placed on the lead wires.

13 Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw lock

washer

Install wall control unit to outlet box

using machine screws provided.

Attach front cover to wall control

with screws provided.

Twist lower cover plate into place by

twisting in direction of arrow.

Replace 1 screw removed and tighten

all 4 screws securely.

Check the motor for shipping stabilizer

and remove if present. The screws, wash-

ers and motor pads are pre-installed to

the blade holders. Attach blade assembly

to motor and tighten screws securely.

Remove cover by snaping off from

top or bottom. Install 12V battery

into wall remote. Duracell MN21 /

Eveready A23 / GP 23A all 12V.

Attach cover of remote by placing

over buttons and snaping into place.

Loosen 4 screws on lower cover

plate. Plug white wire from fan to white

wire from light kit. Then plug black

wire from fan to black wire from light

kit.

22 23

Place glass on light kit, hold in place

and tighten finial cap in direction of

arrow.

Install the 2 x 50 watt halogen

bulbs. Do not touch bulb surface as

oily residue from skin can cause the

bulb to explode.

Place light kit over screws and twist

direction of arrow into place. Then

tighten all 4 screws securely.

Loosen 3 screws with key slots and

remove the 1 screw with closed slot.

Save screw removed.

To control fan speed select from High, Medium

or low speed buttons. To turn the fan off press

the Fan on / off button. To dim upper lights

press and hold U/L botton. To dim Lower lights

press and hold D/L button. To turn off either

up or down light press and quickly release

either U/L or D/L button.

Fan speed

control but-

tons

Fan on / off

Light dim-

mer for up

and down

lights

Reverse function for this fan is a

switch on top housing of the fan

body. Turn fan off and flip switch to

reverse the direction of the blades.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check to make sure the dip switches from the transmitter and receiver are set on the same

frequency.

CAUTION: Make sure main power is turned off

4.Make sure forward/reverse switch is firmly in position. Fan will not operate when switch is

in the middle.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls. DO

NOT USE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance from

blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-

tioned for measurement. Repeat for each blade. If all blade levels are not equal, you can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer

(not supplied) between the blade and blade holder at the screw closest to the motor. To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at the

two screws farthest from the motor. Reverse the position of the washer if blades mount from

top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

WARNING: Before attempting to replace the fuse make sure the main power is

turned off to the fan. Replace only with 3 amp fuse. Fuse is in canopy.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis-

connecting means to prevent power from being switched on accidentally. When the service dis-

connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Customer Service Center:

740 S.W. Loop 820, Suite 110

Fort Worth, Texas 76115

1-800-519-4092

Trouble Suggested Remedy

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3LR38 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CLR66 D-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TTHR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AKR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKDR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Diamond 4DDR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PPR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4GIR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSR60AGD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Titus Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CZ52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SI Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 8EEDR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3BvR52XXd-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 ND Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BCTR20 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5hM52XX series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MS52RB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company MC263 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VMR84 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52RZWD-V1 Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung