Monte Carlo Fan Company 3MO52XXO-L series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach sa es receipt to this card and retain as your proof of purchase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To register your fixture, p ease visit our website www.montecar ofans.com

3MO52XXO-L / 3MTR38XXO-L Series Fans

Tota fan weight with ight kit

UL Model umber of 3MO52XXO-L: 52HH

UL Model umber of 3MTR38XXO-L: 38HH

WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G

READ A D SAVE THESE I STRUCTIO S

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA 70-1999), including

fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the

outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed carefully up

into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the

trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign

object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RC manufactured by Rhine Elec-

tronic Co., Ltd.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

ever place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufac-

turer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the American Society for Heating, Refrigera-

tion and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Cutomer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecar ofans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. To reduce

the risk of fire, electric shock, or personal injury,

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet box is securley fas-

tened by at least two points to a structural ceil-

ing member ( a loose box will cause the fan to

wabble). se only the screws provided with

the outlet box.

Carefully turn the motor over so that

the upper housing is facing up. Re-

move the 3 screws holding the upper

housing. Save for later use.

Lift off the upper housing to reveal

the motor.

lace the fan body with the light fitter

pointing upward. Attache the 3 blades

as shown above.

lace the blade ring holder over

the leadwires and safety cable.

lace the blade ring holder onto

the blades aligning the screw

holes from the blades and ring

holder.

Install the motor screws by tighten-

ing securely.

lace the rubber gasket on the yoke

by threading the leadwires and safety

cable through the rubber gasket

aligning the holes from the gasket

and yoke.

Loosen set screw and then remove

cross pin from yoke for downrod

to slip into yoke. Keep the cross

pin for later use.

For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be in-

stalled into the house structure beams using the

3” lag screws,washers, and lock washers. pro-

vided. Make sure that when the safety cable is

fully extended the leadwires are longer than the

cable and no stress is placed on the leadwires.

18 Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw

lock

washer

Re-place the upper motor housing onto

the fan motor. Be sure the holes are all

aligned.

Note: Align the hole on top housing la-

beled “REVERSE” with the reverse switch.

Tighten the screws removed from

step 5. Tighten securely.

lace the canopy over the downrod

as shown above.

Thread the leadwires and safety

cable through the downrod.

lace the downrod into the yoke

aligning the holes on downrod with

the holes on the yoke and then re-in-

stall the cross pin removed in step

12. Tighten securely.

Tighten the set screw on the yoke.

Hang the assembled fan from the

mounting bracket. Be sure to turn

the fan to lock the ridges from the

fan and mounting bracket in place.

Set screw

Cross pin

Reverse switch

Lift the canopy up and twist to lock

into place. Tighten the screws se-

curely.

Install a 75w JD E-11 base halogen bulb. Bulb is

included.

WARNING: Over lamping the fan will

result in the fan lights shutting down

until the proper wattage of bulbs are

installed. Reset the lights by turning off

the wall switch, breaker,or by remote. Re-

place bulbs with the correct wattage bulbs,

turn the power on.

Slide remote receiver into mounting

bracket.

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Blue from fan to blue from remote marked

light. Black from fan to Red from remote

marked L. White from house to white from re-

mote marked AC N . Black from house to

Black from remote marked AC L. Connect all

green ground wires to Ground wire from

House.

white

Red

Set dip switches on the Remote Transmitter and Remote

Receiver to the same settings. This must be done so the

units will communcate properly. If you have other fans

you can set to control from one transmitter by setting both

receivers the same as the transmitter. If you have more

than one fan with remote. You can set the dip switches to

different positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches

Make wire connections to power source using wire nuts

provided. Make sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on the

other side of the outlet box.

Attach the glass aligning the dimples

from the glass and twist to lock into

place.

Remove cover by snaping off from top or bot-

tom. Remove battery cover. Install 12V battery

into wall remote. Duracell MN21 / Eveready A23

/ G 23A all 12V.Attach cover of remote by plac-

ing over buttons and snap the battery cover in

place.

lace face plate over battery compartment and

buttons. lace remote over 2 pins on front

cover. Attach cover of remote by placing over 4

pins and snaping into place.

26 HAND HELD INSTALL

Reverse function for this fan is a

switch on top housing of the fan

body. Turn fan off and flip switch this

will reverse the direction of the

blades.

Install wall control unit to outlet box

using machine screws provided.

Attach front cover to wall control

with screws provided. Snap battery

cover in place.

WALL MOUNT INSTALL

Reverse switch

Remote Control Transmitter Features:

FAN SPEED Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for

high. To turn fan off press square”.

LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn off

press once quickly while light is on. To dim light hold down button “light dimmer”.

The light will cycle from bright to dim to bright until button is released. Light will

maintain last setting if turned off.

HIGH S EED

MEDIUM S EED

LOW S EED

FAN OFF SETTING

(Turns fan off only)

LIGHT ON/OFF SET-

TING AND DIMMER

( ress and hold to

dim light infinitely)

LED LIGHT

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check to make sure the dip switches from transmitter and receiver are set on the same frequency.

CA TION: Make sure main power is turned off.

4.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when

switch is in the middle.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

CA TION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls.

DO NOT SE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this

period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and

junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting

a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to

ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-

ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the fol-

lowing procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and

blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not supplied)

between the blade and blade holder at the two screws farthest from the motor. Reverse the position

of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute

the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CA TION: Make sure main power is turned off before entering switch housing or canopy.

WARNING: Over lamping the fan will result in the fan lights shutting down until the

proper wattage of bulbs are installed. Reset the lights by turning off the wall switch,

breaker,or by remote. Replace bulbs with the correct wattage bulbs, turn the power on.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble

Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our Cus-

tomer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Dec.2011 new format

Jan.2011 Update customer service phone number

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company MC1215 Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company 5EG60XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LDO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4MC20 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24BS Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Mach One Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD-L Series Fan Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLMR56XXXD-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YM52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BUR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LOR52BSD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CQM44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SIEP Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company MCM360 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Maverick 3MGMR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVLCR54XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVOR56 D-V1 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5hM52XX series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PE56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OBR52 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLNSM52 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung