Monte Carlo Fan Company Mach One Series Bedienungsanleitung

Quality Ceiling fans

Owner’s

Manual

Ceiling Fan Installation Instructions

For Mach One Series Fans

READ AND SAVE THESE INSTRUCTIONS

Total fan weight

with light kit

included

Attach ring blade holder to blades with

the 6 screws provided as shown in fig. A

above. Make sure all screws holding

blades are tight before proceding to the

next step. Re-attach upper housing to

main body using reverse of step 5 as

shown in fig. B above.

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-

1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

the floor to the trailing edge of the blade.

WARINING: MOUNT ONLY TO AN OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT. To reduce the risk of fire, electric shock, or

personal injury, mount to outlet box or supporting system acceptable for fan support. (Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equip-

ment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

10.

11.

12.

13.

14.

15.

Installation

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

SAFETY TIPS

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Place fan body with light fitter point-

ing upward. Attach the 3 blades as

shown in diagram above.

Carefully turn fan motor over so that the

upper housing is facing up. Remove the 3

screws holding the upper housing in

place. Lift upper housing to reveal the

motor. Save screws for step 6.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Unpack and inspect fan carefully to

be certain all contents are included.

Ring blade holder Screws

from

step 5

A. Carefully lift fan assembly onto

mounting bracket. Rotate fan so that

the notch on the ball engages the

ridge in the mounting bracket. This

will allow hands-free wiring.

Install mounting bracket to outlet

box in ceiling using the screws and

washers provided with the outlet

box.

Remove canopy and downrod from polyfoam.

Slide canopy over downrod as pictured. Feed

lead wires through downrod and install down-

rod into fan yoke. Install cross pin with locking

washer through yoke and downrod making sure

to tighten securely. Install set screw into yoke

and tighten securely.

While the fan assembly is still on the

ground thread the safety cable

through the mounting bracket.

Lift fan assembly and install the safety cable

directly to the building structure using the 3”

lag screw and plain washer provided. Before

proceeding to the next step make sure that the

cable is properly installed and will support the

fan weight. Make sure the screw washer and

safety cable are installed using the order pic-

tured above.

Installation

safety cable

mounting

bracket

downrod

canopy

crosspin

yoke

Raise the canopy up and align the two holes in

the canopy with the two holes in the hanger

bracket. Secure with two 5/32” x 1/2” screws

provided.

Install 75W MAX JD type Halogen lamp into

lampholder. Install glass by turning clockwise

until locked in position.

Install 9v battery by removing cover on back of

transmitter and connecting to terminals and re-

install cover.

FAN SPEED Depress “1” for low speed, “2” for

medium or “3” for high. To turn fan off press “0”

LIGHT DIMMER To turn light on, press the button

with bulb icon once quickly. To turn off press once

quickly while the light is on. To dim light hold down

button and bulb icon. The light will cycle from

bright to dim to bright until button is released.

Light will maintain last setting if turned off. Note: If

power is interrupted to fan light will come on at

brightest setting.

Make connections as shown above. Make sure

all exposed conductors are in the wire nuts.

After all connections are made push wire nuts

into junction box with wire nuts pointing

upward.

14 WIRING DIAGRAM

Before installing the remote receiver. Make sure

the DIP switches in the transmitter and receiver

are set the same. Use instrument with a sharp

point to move the switches into the proper posi-

tions. The remote will not operate if this proce-

dure is not done. If interference from outside

transmitters or other remote devices is incoun-

tered, change the dip switch settings on both

transmitter and receiver.

REMOTE OPERATION

Battery

compart-

ment

Light

control

button

Fan

speed

controls

Carefully insert remote receiver into the mount-

ing bracket. Make sure the antenna is not

pinched by running it through the mounting

bracket first (Fig.A). Receiver should be located

as pictured above (Fig.B). Make wiring connec-

tions as per step 12. Make sure that all wire nut

connections are tight with no exposed conduc-

tors. Point connectors upward and push into the

junction box.

Fig.BFig.A

Wire nuts

Remote

receiver

Antenna

Remote

receiver

Remote

transmitter

DIP

switches

Green (ground)

White (common)

Black (hot) Fan

Blue (Hot) Light

Plain (ground)

Black (hot)

White (common)

HOUSE FAN

Blue to Light

Red to Fan Motor

Black to House

White to Fan

White to House

REMOTE RECEIVER

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check to make sure the dip switches from the transmitter and receiver are set on the same

frequency.

4.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when

switch is in the middle.

CAUTION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other

or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls.

DO NOT USE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance from

blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-

tioned for measurement. Repeat for each blade. If all blade levels are not equal, you can adjust

blade levels by the following procedure. To adjust a blade tip down, insert a washer (not sup-

plied) between the blade and blade holder at the screw closest to the motor. To adjust a blade

tip up, insert washer (not supplied) between the blade and blade holder at the two screws far-

thest from the motor. Reverse the position of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redis-

tribute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to blue wire from remote receiver.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis-

connecting means to prevent power from being switched on accidentally. When the service dis-

connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

SUGGESTED REMEDY

TROUBLE

Customer Service Center:

1-800-519-4092

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5CO52RB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PPR54XX Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company 4ICR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVO52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YM52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SY52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ED56WAD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LCR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 8TNR56 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8TNR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8EER60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BY52XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DSTR57 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LWDSM60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WS52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MO52XXO-L series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLMR56XXXD-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VTR52/38 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LDO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company TRAVERSE 5TV52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CMR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VLR60 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung