Monte Carlo Fan Company 3TSR52XXD Series Bedienungsanleitung

QUALITY CEILING FANS

Ceiling Fan Installation Instructions

For 3TSR52XXD Series Fans

READ AND SAVE THESE INSTRUCTIONS

Total fan weight

with light

OWNER’S

MANUAL

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),

including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-

ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7

feet from the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

Use only the screws provided with the outlet box. Use only the screws provided with the outlet box. (Mounting must support at least

35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating

blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-

ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such

as a tag, to the service panel.

10.

11.

12.

13.

14.

15.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

SAFETY TIPS

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. To reduce

the risk of fire, electric shock, or personal injury,

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet box is securley

fastened by at least two points to a structural

ceiling member ( a loose box will cause the fan

to wabble). Use only the screws provided

with the outlet box.

Installation

Remove keeper from pin. Replace

keeper into pin and save for

later.

Loosen the 2 set screws in yoke

for downrod to slip into yoke.

Place canopy and then yoke

cover on downrod. Thread lead-

wires and safety cable through

downrod. As shown.

Hang assembled fan from the mounting bracket

installed to ceiling in previous step. Make sure the

fan is hanging straight. Rotate fan until the tab on

the Mounting bracket engages the slot on the

Downrod Ball. This must be done to prevent the fan

body from rotating when the blades are in motion.

Next lift the canopy, twist into place and

tighten 2 screws securely. The canopy

should adjust for any irregularity in the

ceiling or Outlet box.

Insert downrod into yoke on top of the Fan

Body. Align the hole in the Downrod with the

hole in the Yoke. Insert the Pin through the

Yoke and Downrod until the point appears on

the other side. Install the keeper to pin.

Tighten the 2 set screws on the Yoke

once the downrod is in place.

Make wire connections to power source using wire nuts

provided. Make sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on

the other side of the outlet box.

For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be

installed into the house structure beams using

the 3” lag screws,washers, and lock washers.

provided. Make sure that when the safety cable

is fully extended the leadwires are longer than

the cable and no stress is placed on the lead-

wires.

9Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw

lock

washer

Slide remote receiver into mounting

bracket.

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Blue from fan to blue from remote marked

light. Black from fan to Black from remote

marked L. White from house to white from

remote marked AC N . Black from house to

Black from remote marked AC L. Connect all

green ground wires to Ground wire from

House.

white

black

Set dip switches on the Remote Transmitter and Remote

Receiver to the same settings. This must be done so the

units will communcate properly. If you have other fans you

can set to control from one transmitter by setting both

receivers the same as the transmitter. If you have more

than one fan with remote. You can set the dip switches to

different positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches

Align the blade with castings on

motor to attach blades to motor.

Loosen 2 screws and remove 1 screw

from motor plate and save screw.

Install light plate by twisting plate

with key hole slots into place.

Replace screw removed and tighten

the 3 screws securely.

Attach front cover to wall control

with screws provided.

Install wall control unit to outlet box

using machine screws provided.

To control fan speed select from High,

Medium or low speed buttons. To turn

the fan off press the Fan on / off button.

To dim lights press and hold button. To

turn off light press and quickly release

button. Press button marked REV to

reverse the rotation direction of the fan

blades

Fan speed

control

buttons

Fan on / off

Light dimmer

for lights

Fan

reverse

button

Remove cover by snapping off from

top or bottom. Install 12V battery

into wall remote. Duracell

MN21/Eveready A23/GP 23A all 12V

Attach cover of remote by placing

over buttons and snapping into

place.

Connect white wire from fan to white

wire from light fixture. Then plug

black wire from fan to black wire

from light fixture.

Install light fixture by twisting plate

with key hole slots into place.

Replace screw removed and tighten

the 3 screws securely.

Install 3 x 60 watt incandescent can-

delabra bulbs.

Attach glass by locating dimples in

light fixture with the groves in glass

and twisting clockwise till tight.

Loosen 2 screws and remove 1 screw

from light plate and save screw.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check to make sure the dip switches from transmitter and receiver are set on the same frequen-

cy.

CAUTION: Make sure main power is turned off.

4.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when

switch is in the middle.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls.

DO NOT USE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after

this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and

junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting

a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to

ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-

ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the fol-

lowing procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and

blade holder at the screw closest to the motor

. To adjust a blade tip up, insert washer (not supplied)

between the blade and blade holder at the two screws farthest from the motor

. Reverse the posi-

tion of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistrib-

ute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing or canopy.

WARNING: Before attempting to replace the fuse make sure the main power is

turned off to the fan. Replace only with 3 amp fuse. The fuse is inside the canopy.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble

Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our

Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Customer Service Center:

740 S.W. Loop 820, Suite 110

Fort Worth, Texas 76115

1-800-519-4092

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLNSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CNR52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Edge Coastal 60 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVMR64 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LDO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3KNR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CZ52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIW52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Maverick II 3MAVR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HLR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PPR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MS52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ASPR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PEN56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Launceton 56 4LNCR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WS52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AB52XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MAR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AXR52XX3-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YK60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 ND Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung