Monte Carlo Fan Company 3CLNSM60 Series Gebrauchsanweisung

Total fan weight

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

3CLNSM60XXX Series Fan

cETL Model NO. : 3CLNSM60XX

6.33 kg

14 lbs

Owner’s Guide and Installation Manual

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including

ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed

carefully up into the outlet box.

WARNING: Before you begin installing, servicing or cleaning the fan unit, switch the power off at the service panel and lock the service panel to prevent

the power from being switched back on accidentally. If the service panel cannot be locked to prevent the power from being switched on accidentally,

securely fasten a warning sign to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the ﬂoor

to the trailing edge of the blade.

WARNING: To reduce the risk of ﬁre, electric shock, or personal injury, mount to outlet box marked “Acceptable for Fan Support of 15.9 kg (35 lbs) or

less” and use mounting screws provided with the outlet box.

CAUTION: Comply with local codes and regulations. If installing the secondary support safety cable in the U.S., do not remove knockouts in the outlet

box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure or the ceiling joist.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert

foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. JY1126O manufactured by Satellite

Electronic (Zhongshan) Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment

manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is required, the

product should be returned to an authorized service facility for examination or repair.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in damp locations. Install the fan under covered or enclosed patios or porches.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, FOLLOW THESE INSTRUCTIONS.

1 2 3

4 5 6

OFF

Switch power off at Service panel.

Lock service disconnecting means to

prevent power from being switched on

accidentally.

When the service disconnecting means

cannot be locked, securely fasten a

warning device, such as a tag, to the

service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure.

To reduce the risk of ﬁre, electric shock,

or personal injury, mount to outlet box or

supporting system acceptable for fan

support. (Mounting must support at least

35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35 lbs).

Before attaching fan to outlet box, ensure

the outlet box is securely fastened by at

least two points to a structural ceiling

member (a loose box will cause the fan to

wobble).

Remove the 2 outlet box screws provided

with the box, aligning the holes of the

mounting bracket with the holes of the

outlet box.

Reinstall the 2 outlet box screws securely.

Place motor assembly on a suitable area

of paper pulp for blade installation.

Aligning the holes on the blade with the

screw holes on the motor as shown in the

illustration.

Install the blade with a blade supporting

plate. Partially install blade set screws as

shown in the illustration. Set screws

provided.

Warning: Blades, blade supporting plate

and blade mounting screws must be

installed for operation; failure to install

either will void the limited lifetime

warranty

Install the other 2 blades. Adjust the

blades to make the gaps between blades

even and then tighten all the set screws

securely.

Mounting bracket

Blade

Blade supporting plate

7 8 9

10 11 12

Place a rubber pad and a top cover over

lead wires and safety cable and install the

top cover onto the yoke with set screws

provided.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Remove preassembled keeper pin and

cross pin from downrod. Keep parts.

Place downrod over canopy, canopy

bottom cap and yoke cover.

Connect the extension lead wires to the

lead wires from motor. Make sure the

quick connectors are clasped ﬁrmly.

Thread lead wires and safety cable from

motor assembly through downrod.

Note: Make sure the plugs connections

won’t be pulled apart.

Slip downrod into motor housing yoke,

aligning holes and install cross pin and

keeper pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the cross

pin, and then evenly tighten the downrod

set screws on motor housing yoke.

Place yoke cover on top housing of fan.

Warning: Cross pin and keeper pin must

be installed securely. Failure to install them

will result in serious injury.

Install ball end of downrod into mounting

bracket opening.

Align (engage) slot on ball with tab on

mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper than 20º. Longer downrod

may be necessary allowing the fan blades

to rotate without obstructions.

Safety cable must be installed into the

house structure using 3” lag screws,

washers, and lock washers provided,

required for outdoor applications and in

Canada (All fans installed in Canada), and

for USA fan and light kit combinations

over 35lbs.

Make sure that when the safety cable is

fully extended, the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If installing the secondary support

safety cable in the U.S., do not remove

knockouts in the outlet box.

Yoke

Downrod

Cross pin

Keeper pin

Tab

Slot

Top cover

Canopy

Downrod

Yoke cover

Canopy bottom

cap

Extension lead wire

Cross pin Keeper pin

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Rubber pad

Make wiring connections using wire connectors provided as indicated above.

Brown wire from fan to Brown wire from receiver marked Motor U.

Gray wire from fan to Gray wire from receiver marked Motor V.

Blue wire from fan to Blue wire from receiver marked Motor W.

White (Neutral) wire from house to White wire from remote marked AC IN N.

Black (Live) wire from house to Black wire from remote marked AC IN L.

Connect all green grounded wires to Grounded wire from House.

Make sure that no ﬁlaments are outside of the wire connectors.

Insert the remote receiver into mounting bracket.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices after being made should be

turned upward and pushed carefully up into the outlet box.

Place the wi-ﬁ antenna outside canopy and stick/ﬁx it onto ceiling.

Caution: The installation has to be complete before operate the fan. The receiver has to be used on the fan and cannot be

bypassed.

Partially loosen one and remove one

preassembled screw from mounting

bracket. Save screw.

Lift canopy up, aligning its keyhole slot

with the preassembled screw on

mounting bracket and twist clockwise to

lock in place. Reinstall the other screw

and tighten all screws securely.

Attach canopy bottom cap onto canopy

by aligning its holes with the screws on

mounting bracket and ﬁx it with the

magnet which is embedded in the cap.

Canopy bottom

cap

Wall switch Black

Power source Brown Grey

White Blue

White

Black

Ground/Green

Receiver

Wi-Fi antenna

Canopy

Battery cover

SET

The remote control buttons control the fan speed as follows:

Fan speed

1 = minimum speed 2 = low speed 3 = medium low speed

4 = medium speed 5 = medium high speed 6 = high speed

This button turns the fan off.

Forward/Reverse button: This button is to control direction of fan rotation. Press once

to change direction of the fan rotation. Fan must be running to reverse.

Breeze:

Press the Breeze button, fan will operates randomly among minimum, low and medium low speed at

intervals of 30 seconds until the breeze mold is canceled.

Breeze mode can be erased by pressing either the power or speed control buttons.

Note

: This remote controller has auto resume function. The fan will maintain the last setting when

turned back on, with the exception of Breeze mode.

Remote Controller Operation

Remove the battery cover from the remote control transmitter and install batteries.

Replace the cover. This remote uses 2 1.5V/AAA batteries.

Note: If not using for long periods of time, remove the batteries to prevent damage to

remote controller, and store the remote controller away from excess heat or humidity.

The batteries will weaken with age and should be replaced before they leak or corrode as

this will damage the controller. Dispose of the used batteries properly. Always keep

batteries out of the reach of children.

Universal Mode and Learning Mode

Your remote controller has two options: “Universal Mode” (mark “0”) and “Learning Mode”

(mark “1”).

If choosing “Universal Mode,” simply move the switch to the LOWER position (mark “0”).

Your fan with the remote controller is ready to use.

Note: If using Universal Mode, your fan can be controlled with other remote controllers

with the same setting.

To control the fan with a speciﬁc remote controller, choose “Learning Mode” by moving the

switch to the UPPER position (mark “1”) and then follow the Learn Mode steps below.

Learn Mode

Important: Turn the power on for ONLY the speciﬁc fan you wish to pair with the remote

controller. Make sure to turn the power off for all other fans with which you use the same

remote controller.

Restore power to your fan, press and hold the “SET” button to pair the transmitter and

receiver. You must press the ‘SET” button within 60 seconds of restoring power to the fan.

Note

: Fan will at ﬁrst operate at minimum speed and light will blink (if your fan has a light)

after you’ve chosen Learn Mode.

Note

: If the power is already on, you must turn the power off and then back on for the

remote control setting.

Note

: If you reset the controller to Universal Mode (mark “0”) and later want to pair the

controller again to a speciﬁc fan, you have to repeat the Learn Mode steps.

Wall mount cradle

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS. (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

The receiver provides the following protective functions:

Lock protection: The DC motor has a build-in safety feature

against blade obstruction during operation. If something

obstructs the fan blades, the motor will stop operation after

about 20 seconds of interruption. Please remove obstacles

and reset it by turning the power off, and then turn power

back on.

Over 40W protection: When the receiver detects motor

power consumption which is greater than 40W, the fan RPM

will automatically lower to prevent it from overloading.

User Tips

1. If your fan is operating automatically after installation, it is still using the factory setting. Follow the settings for Learn Mode

above to reset.

2. If the fan or light isn’t working, reset power (turn the power off then turn the power back on) and follow the Universal Mode or

Learn Mode remote control settings.

3. If two or more fans in the same remote signal range are on the same power supply, they cannot be operated separately by

remote control. Use a separate power supply for each fan, such as an individual wall switch, and restrict the power supply to

only the fan which you are pairing with its transmitter in order to use the remote controller.

4. When the fan is turned on to oscillate in either forward or reverse direction, it may shudder brieﬂy until fully engaged. This is a

normal operation for this fan; the shuddering will quickly cease as movement is engaged.

Install Transmitter wall mount cradle with 2 screws provided.

Useful tips:

The remote transmitter can be removed by pressing it

upward from the lower half.

The remote transmitter can be held on magnetic metal

materials by a magnet built in the transmitter.

Download the Bond Home app with your smart devices. The app is available on the

Google Play Store and Apple Store.

Or get it from bond home link, http://bondhome.io/app

Create a new account following on-screen operating steps.

Make the fan (Smart by Bond wi-ﬁ receiver) connection with wi-ﬁ router. Within 60

seconds of restoring power to the fan, Press and hold the “Power” button of

transmitter for 5 seconds until light blinks and fan runs at lowest speed for about 10

seconds. Your fan has now successfully learned the transmitter.

Note: If you haven’t made “learn” function setting for the fan remote yet. You may

handle it via the bond app. On the fan operation UI, tap device setting “ or ”

at upper right area and select Manage Remotes.

Note: Check and make sure power on and Wi-Fi router is functional.

To add a new device. Press “+” and choose Smart by Bond, and following on-screen

information and set up your fan (Wi-Fi receiver) with smart phone/device and Wi-Fi

router.

Tap “Settings” on the bond app, select Schedules and following on-screen

information to set up schedule.

Note: If “Bond Conﬁguration” Wi-Fi network cannot be found, try pressing and

holding the button of power on the remote transmitter for 10 seconds, the Wi-Fi

network should re-appear.

Note: You may control fan from multiple smart phones or tablets by logging onto

the same Bond Home account on all the smart phones/tablets.

Fan operation with Bond Home APP

Compatible with Amazon Alexa, Google Home and Samsung SmartThings

Tap “Settings” on the bond app, select Manage Integrations and you may ﬁnd the

Smart Cloud integrations.

Or you may download Alexa, Google Home, Samsung SmartThings app. You may

need to sign up an account if you don’t have it yet. Sign in your Alexa/Google

Home/Samsung SmartThings account.

- Login Amazon Alexa, Google Home or Samsung SmartThings app to enable the

skill and discover the MC Fan with Smart by Bond wi-ﬁ receiver.

- Come back to the Smart device with bond app and deﬁne the device/MC Fan.

Connect to Amazon Echo, Google Home or Samsung SmartThijngs to make your fan

can be voice-activated, and available with UI (User interface) of Amazon Echo,

Google Home or Samsung SmartThings.

Initialize (Factory reset) the wi-fi receiver

If there are questions on the fan operation with bond app, following below steps to initialize the wi-ﬁ receiver and redo bond app

stetting.

Turn the fan power off, and then turn the power back. Within 30 seconds, press and hold the button of the ﬁrst speed/1st on the

transmitter for 15 seconds until light blinks. The receiver has been initialized.

Wait for 10 seconds and redo bond app setting.

Initialization (Factory reseting) can also be performed via the app: Tap device setting “ or ” and then tap “ or ” at upper

right corner to remove device, and then select “Wipe All Data”.

Troubleshooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning

and lock the service panel to prevent the power from being switched back on accidentally. If the service panel

cannot be locked to prevent the power from being switched on accidentally, securely fasten a warning sign to the

service panel.

1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in switch housing.

CAUTION

either way. Fan will not operate when switch is in the middle.

4. If this fan uses a remote controller, make sure dip switches are in the correct setting

and make sure the battery works.

1. Check to make sure all screws in motor housing are snug (not over tightened).

2. Check to make sure the screws which attach the fan blade holder to the motor are tight.

3. Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION

4. Check to be sure lightbulb is tight in socket and not touching the glass shade.

5. Some fan motors are sensitive to signals from Solid State variable speed controls.

6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will

disappear after this period.

1. If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2. Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4. Check that all blade holders are tightened securely to motor.

5. Most fan wobble problems are caused when blade levels are unequal. Check this level

by selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceiling. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6. If blade wobble is still noticeable, interchanging two adjacent blades can redistribute the

weight and possibly result in smoother operation.

If the above steps do not eliminate the wobble problem, you will need to dynamically

balance your fan with balancing kit provided.

1. Check blue wire from fan to make sure it is connected to hot wire from house.

2. Check for loose or disconnected wires in fan switch housing.

3. Check for loose or disconnected wires in light kit.

4. Check for faulty lightbulb and make sure bulb is tight in socket.

5. Remove light kit and check the plug connections if they are present.

6. If this fan uses a remote controller, make sure dip switches are in the correct setting

and make sure the battery works.

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Aug.2021

Nov.2021 update about UI of Bond App

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5PEN56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BS52 Builder Supreme Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company ERA 3ERHR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3LD48 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5hM52XX series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 14PRR62XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MYR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WA52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BHM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3OBSHR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PPR54XX Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company BF2 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LDO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Bravo 5BO52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LNR52 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VTR52/38 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Linden 5LD52 F Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Launceton 56 4LNCR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company studio series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3BvR52XXd-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ELR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 25003 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 D-V1 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung