Monte Carlo Fan Company 3AVMR64 D Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Total fan weight with light

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

3AVMR64XXD Series Fan

ETL Model NO. : 3AVMR64XXXXX

7.95 kgs

17.5 lbs

3 0 6 4 9 6 4

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the

building structure (or the ceiling joist).

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To Reduce The Risk Of Electric Shock, This Fan Must Be Installed With a general use, isolating Wall Control/Switch.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. DC8 manufactured by

Carewell Electric Technology (Zhongshan) Co.,Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable

speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is

required, the product should be returned to an authorized service facility for examination or repair.

All set screws must be checked, and re-tightened where necessary, before installation.

Note: Suitable for use in damp locations.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35 lbs).

Before attaching fan to outlet box, ensure

the outlet box is securely fastened by at

least two points to a structural ceiling

member (a loose box will cause the fan to

wobble). Remove the two outlet box

screws provided with the box, aligning

the holes of the mounting bracket with

the holes of the outlet box. Reinstall the 2

outlet box screws securely.

Put blades together, overlap edges of

blades one another and align the holes

each other and then assemble the blades

with wood screws provided. Do not over

tighten.

Note: For easy assembling and avoiding

blade damage from scratch, put blades

on Styrofoam as shown above.

Flick blade assembly over and place it on

motor.

Align the holes as shown in graphic and

install blade assembly onto motor with

set screws provided. Tighten set screws

securely. Do not over tighten.

Mounting bracket

Blade assembly

Motor

Wood screw

Blade

Top styrofoam

7 8 9

10 11 12

Remove preassembled keeper pin and

cross pin from downrod.

Place downrod over canopy, canopy

bottom cap and yoke cover.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Thread lead wires and safety cable from

motor assembly through downrod.

Slip downrod into motor housing yoke,

aligning holes and install cross pin and keeper

pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the cross

pin, and then evenly tighten the downrod set

screws on motor housing yoke.

Place Yoke cover on motor assembly.

Warning: Cross pin and keeper pin must be

installed securely, failure to install them will

result in serious injury.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 1.5” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Keeper pin

Cross pin

Downrod

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper

than 25º.

Canopy

Downrod

Yoke cover

Yoke

Keeper pin

Cross pin

Downrod

Yoke cover

Set screws

Canopy

Tab

Downrod

Slot

Lead wire Safety cable

Canopy

Downrod

Yoke cover

Canopy bottom

cap

Canopy bottom

cap

Canopy bottom

cap

15 17

Make wiring connections using wire connectors provided as indicated above.

Red from fan to Red from remote marked Motor 1.

Purple from fan to Purple from remote marked Motor 2.

Gray from fan to Gray from remote marked Motor 3.

Blue from fan to Blue from remote marked FOR LIGHT.

White from fan to White from remote marked FOR LIGHT.

White (Neutral) from house to White from remote marked AC IN N.

Black (Live) from house to Black from remote marked AC IN L.

Connect all green grounded wires to Grounded wire from House.

Make sure that no ﬁlaments are outside of the wire connectors.

Insert the remote receiver into mounting bracket.

After making the wire connections, the wires should be spread apart with the grounded

conductor and the equipment-grounding conductor on one side of the outlet box and

ungrounded conductor on the other side of the outlet box. The splices after being made should

be turned upward and pushed carefully up into the outlet box.

Lift canopy up, aligning its keyhole slot

with the preassembled screw on

mounting bracket and twist

counterclockwise to lock in place.

Reinstall the screw removed in step 14

and tighten all screws securely.

Attach canopy bottom cap onto canopy

by aligning its notch with the screws on

mounting bracket and twist clockwise till

tight.

Loosen 2 and remove 1 preassembled

screw from the plate on motor. Save

screw for later use.

Place light pan over the lead wires and

attach it onto the plate on motor, aligning

the keyhole slots on the light pan with the

preassembled screws on the plate. Twist

clockwise till lock.

Partially loosen one and remove one

preassembled screw from mounting

bracket. Save screw.

Blue (For Light)

White (For Light)

Red (Motor 1)

Purple (Motor 2)

Gray (Motor 3)

Black (AC IN L)

White (AC IN N)

Green/Ground

Wall Switch

Ground/Green

Black (Live)

White (Neutral)

Power source

Receiver

Plate on motor

Light pan

18 2019

21 22 23

Reinstall the screw removed in step 16.

Tighten all screws securely.

Connect white wire from fan to white wire

from LED light kit and then connect blue

wire from fan to blue wire from LED light

kit.

Note: If you don’t want to install the

fan with LED light, go to step 23 for

blanking plate installation.

Remove 3 preassembled screw from the

light pan. Save screws for later use.

Attach LED light kit onto the light pan,

aligning the holes on the LED light kit with

the screw holes on light pan. Reinstall the

screws removed in step 19. Tighten all

screws securely.

Attach lexan shade by locating dimples in

light pan with grooves on the Lexan

shade and twist clockwise until tight.

Attach blanking plate by locating dimples

in light pan with grooves on the blanking

plate and twist clockwise until tight.

Note: Do not install LED light kit if

use blanking plate.

Install LED Light Kit

Light pan

Lexan shade

Light pan

Install Blanking Plate

Blanking plate

LED light kit

REMOTE CONTROL SETTING and OPERATION

Universal Mode and Learning Mode

There are “Universal Mode” and “Learning Mode” with the remote controller.

If choosing “Universal Mode”, simply place dip (code) switch at UPPER

position. Your fan with the remote controller is ready to use.

Note: If using universal mode, your fan can be controlled with other remote

transmitters with the same setting.

To control the fan with speciﬁc remote transmitter, choose “Learning Mode”

by placing the dip (code) switch at LOWER position and then make learn

function setting as below.

Learn function setting, Restore power source to your fan, press and hold

the “LEARN” button for at least 3 seconds. You must press the “LEARN”

button within 60 seconds of restoring power to the fan.

Note: If the power is on already, you must turn the power off for 10 seconds

at least, and then turn the power back for remote control learn function

setting.

Note: If the fan is installed with light, light will twinkle 2 times. The remote

control setting process is complete and your fan is ready for use. For fans

without light, check operation using remote transmitter.

Note: If you want to control the fan with another transmitter, make the same

setting. A fan can be controlled by 2 transmitters maximum.

Transmitter Operation

Remove the battery cover from the remote control transmitter and install

battery, battery provided. Replace the cover.

Note: Use 2 1.5V/AAA battery.

Note: If not using for long period of time, remove battery to prevent damage

to remote transmitter, and store the remote transmitter away from excess

heat or humidity.

DIM

LEARN

L.CODE

COMMON

CODE

L.CODE

COMMON

CODE

DIM

Universal Mold

Learning Mold

Dimming / Non Dimming Setting

The “DIM” selection is the light dimmable selection and the light will cycle

from bright to dim to bright until button is released. The “ON” selection is the

light ON/OFF only (non dimming function). Light will maintain last setting if

turned off.

Note: The remote controller is set with dimming function at factory,

Note: If the remote receiver has been wired with fan, turn power off by wall

switch before switch “DIM” and “ON/OFF” selection.

Dimming/

Non dimming

LEARN

Learn

The receiver provides the following protective functions

Lock protection- The DC motor has a build-in safety feature against blade or motor obstruction during operation. If

something obstructs the fan blades or motor, the motor will keep trying to run for 5 times and then stop operation

after about 60 seconds of interruption. Please remove obstacles and reset. To reset it by turn the fan off by remote

transmitter and then turn the fan on, Or you may turn power off for 15 seconds then turn power back, and then turn

the fan on,

Over load protection (current limit)- The device will limits the maximum current output from the receiver/drive when the

fan or light load was increased abnormally.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1)THIS DEVICE MAY NOT

CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE

UNDESIRED OPERATION.

The buttons on the remote control transmitter control the fan speed and light as follows.

Fan speed

1 = minimum speed 2 = low speed

3 = medium low speed 4 = medium speed

5 = medium high speed 6 = high speed

This button turns the fan off.

Forward/Reverse button- This button is to control direction of fan rotation. Press once

to change direction of the fan rotation. Fan must be running to reverse.

Light button- Press this button to turn light on or off. To dim light (

Setting at “DIM”

position

), hold down the button, the light will cycle from bright to dim to bright until button

is released.

Note

: This remote controller has auto resume function, the fan and light will maintain the

last setting if power is turned off.

Tips for end users

1. If your fan is operated automatically after installation and power on, it is because your fan is still memorize the previous

setting at factory.

2. If fan or light isn’t working, reset power (turn the power off for at least 10 seconds and then turn the power back) and redo

the learn function setting.

3. It is not available to separately operate the learn setting for more than one fan in the same room (in the area where remote

signal can reach to) if they share the same power supply. Separate power supplies (like as using individual wall switches for each

fan and turn power off for the fan while you are making learn function for other fan) is required if you want to separately control

more than one fan in same room.

4. When fan is turned on or operated forward/reverse function, it shutters & goes back & forth until it turns. It is a normal

performance of this fan and it will take for few seconds to run this operation.

Install Transmitter wall mount cradle with 2 screws provided.

Wall mount cradle installation

Trouble Shooting

,I\RXKDYHGLI¿FXOW\RSHUDWLQJ\RXUQHZFHLOLQJIDQLWPD\EHWKHUHVXOWRILQFRUUHFWDVVHPEO\LQVWDOODWLRQ

RUZLULQJ,QVRPHFDVHVWKHVHLQVWDOODWLRQHUURUVPD\EHPLVWDNHQIRUGHIHFWV,I\RXH[SHULHQFHDQ\IDXOWV

SOHDVHFKHFNWKLV7URXEOH6KRRWLQJ&KDUW,IDSUREOHPFDQQRWEHUHPHGLHGRU\RXDUHH[SHULHQFLQJGLI¿FXOW\LQ

LQVWDOODWLRQSOHDVHFDOORXU&XVWRPHU6HUYLFH&HQWHUDWWKH

QXPEHUSULQWHGRQ\RXUSDUWVOLVWLQVHUWVKHHW

Warning%HIRUHVHUYLFLQJRUFOHDQLQJXQLW6ZLWFKSRZHURIIDW6HUYLFHSDQHODQGORFNVHUYLFHGLVFRQQHFWLQJ

PHDQVWRSUHYHQWSRZHUIURPEHLQJVZLWFKHGRQDFFLGHQWDOO\:KHQWKHVHUYLFHGLVFRQQHFWLQJPHDQVFDQQRWEH

ORFNHGVHFXUHO\IDVWHQDSURPLQHQWZDUQLQJGHYLFHVXFKDVDWDJWRWKHVHUYLFHSDQHO

&KHFNPDLQDQGEUDQFKFLUFXLWIXVHVRUFLUFXLWEUHDNHUV

&KHFNOLQHZLUHFRQQHFWLRQVWRIDQDQGVZLWFKZLUHFRQQHFWLRQVLQVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRII

,IWKLVIDQXVHV PDQXDO IRUZDUGUHYHUVHVZLWFKPDNHVXUHWKH VZLWFK LV SXVKHG ¿UPO\

HLWKHUZD\)DQZLOOQRWRSHUDWHZKHQVZLWFKLVLQWKHPLGGOH

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

&KHFNWRPDNHVXUHDOOVFUHZVLQPRWRUKRXVLQJDUHVQXJQRWRYHUWLJKWHQHG

&KHFNWRPDNHVXUHWKHVFUHZVZKLFKDWWDFKWKHIDQEODGHKROGHUWRWKHPRWRUDUHWLJKW

&KHFNWRPDNHVXUHZLUHQXWFRQQHFWRUVLQVZLWFKKRXVLQJDUHQRWUDWWOLQJDJDLQVWHDFK

RWKHURUDJDLQVWWKHLQWHULRUZDOORIWKHVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRIIEHIRUHHQWHULQJVZLWFKKRXVLQJ

&KHFNWREHVXUHOLJKWEXOELVWLJKWLQVRFNHWDQGQRWWRXFKLQJWKHJODVVVKDGH

6RPHIDQPRWRUVDUHVHQVLWLYHWRVLJQDOVIURP6ROLG6WDWHYDULDEOHVSHHGFRQWUROV

$OORZEUHDNLQSHULRGRIKRXUV0RVWQRLVHVDVVRFLDWHGZLWKDQHZIDQZLOOGLVDSSHDU

DIWHUWKLVSHULRG

,IWKLVLV DGRZQURGPRXQWIDQ PDNHVXUHWKH ULGJH RQPRXQWLQJEUDFNHWHQJDJHVWKH

QRWFKLQWKHGRZQURGEDOO

0DNHVXUH WKDW FDQRS\ PRXQWLQJEUDFNHWRU PRXQWLQJ SODWHDUH WLJKWHQHG VHFXUHO\ WR

FHLOLQJMXQFWLRQER[DQGMXQFWLRQER[LVPRXQWHG¿UPO\WRFHLOLQJMRLVW

&KHFNWKDWDOOEODGHVDUHVFUHZHG¿UPO\LQWREODGHKROGHUV

&KHFNWKDWDOOEODGHKROGHUVDUHWLJKWHQHGVHFXUHO\WRPRWRU

0RVWIDQZREEOHSUREOHPVDUHFDXVHGZKHQEODGHOHYHOVDUHXQHTXDO&KHFNWKLVOHYHOE\

VHOHFWLQJDSRLQW RQWKHFHLOLQJDERYHWKHWLS RIRQHRIWKH EODGHV 0HDVXUHWKLVGLVWDQFH

IURPEODGHWLSWRFHLOQJ.HHSLQJPHDVXUHZLWKLQURWDWHWKHIDQXQWLOWKHQH[WEODGH

LVSRVLWLRQHG IRU PHDVXUHPHQW 5HSHDWIRUHDFKEODGH,IDOOEODGHOHYHOVDUHQRWHTXDO

\RXFDQDGMXVWEODGHOHYHOVE\WKHIROORZLQJSURFHGXUH7RDGMXVWDEODGHWLSGRZQLQVHUW

DZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGHKROGHUDWWKHVFUHZFORVHVWWRWKH

PRWRU7RDGMXVWDEODGHWLSXSLQVHUWZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGH

KROGHUDWWKHWZRVFUHZVIDUWKHVWIURP WKH PRWRU 5HYHUVHWKH SRVLWLRQ RI WKH ZDVKHULI

EODGHVPRXQWIURPWRSRIEODGH

,IEODGHZREEOHLV VWLOOQRWLFHDEOHLQWHUFKDQJLQJWZRDGMDFHQW VLGHE\VLGHEODGHVFDQ

UHGLVWULEXWHWKHZHLJKWDQGSRVVLEO\UHVXOWLQVPRRWKHURSHUDWLRQ

&KHFNEOXHZLUHIURPIDQWRPDNHVXUHLWLVFRQQHFWHGWRKRWZLUHIURPKRXVH

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQIDQVZLWFKKRXVLQJ

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQOLJKWNLW

&KHFNIRUIDXOW\OLJKWEXOEDQGPDNHVXUHEXOELVWLJKWLQVRFNHW

5HPRYHOLJKWNLWDQGFKHFNWKHSOXJFRQQHFWLRQVLIWKH\DUHSUHVHQW

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

CAUTION0DNHVXUH PDLQ SRZHU LV WXUQHG RII EHIRUH HQWHULQJ VZLWFK KRXVLQJ DQGRU

FDQRS\

,IIDQVRXQGVQRLV\

,IIDQZREEOHV

,IOLJKWGRHVQRWZRUN

,IIDQGRHVQRWVWDUW

Trouble Suggested Remedy

Nov.2016

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3ACR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SH54XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SY52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5hM52XX series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EG60XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4LMR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Jovie 3JOVR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Arcade 3ARR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 6LFR62 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OBR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MMR54 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Haven 5HVO52BKD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AMR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HV52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4CO28 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HV52 F Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SU54BK Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SLR52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5RDR Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8TNR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AGR56XXD series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 D-V1 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung