Monte Carlo Fan Company 5BS52 Builder Supreme Bedienungsanleitung

Page 1 – Builder Supreme-English CUL

92 QUALITY CEILING FANS

Total fan weight

with light kit in-

cluded.

For Builder Supreme Fans

READ AND SAVE THESE INSTRUCTIONS

Ceiling Fan Installation Instructions

OWNER’S

ANUAL

Page 2 – Builder Supreme-English CUL

123

TOOLS REQUIRED

Phillips Scre driver Wire Cutters Pliers Step Ladder

Unpack and inspect fan carefully to be

certain all contents are included. (See

exploded view parts list.)

Turn off power at breaker box to avoid

possible electrical shock.

Use outlet box suitable for fan support.

Secure outlet box directly to the building

structure using ceiling joist screws.

Outlet box must support 35 lbs.

Install mounting bracket to outlet box

in ceiling using the screws and

washers provided with the outlet box. 5

Feed motor lead wires through downrod/

canopy assembly and insert downrod into

motor yoke. Next, insert clevis pin through

yoke and downrod and secure with cotter

pin. (see inset) Tighten both yoke set

screws to further secure downrod. 6

Clevis

Pin Set

Screws

Cotter

Ridge Ball

Notch

Safety Tips

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION

10.

11.

12.

13.

14.

15.

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards(ANSI/NFPA 70-

1996), including fire-rated construction.

Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

ake sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the

floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

Use mounting screws provided with the outlet box. ( ounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NEPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

Carefully lift fan assembly onto

mounting bracket. Rotate fan so that

the notch on the ball engages the ridge

in the mounting bracket. This will allow

hands-free wiring.

Page 3 – Builder Supreme-English CUL

Ball

Notch

Install mounting bracket to outlet box in

ceiling using the screws provided with the

outlet box and washers.

Ridge

Canadian Mounting System Insert

WARNING: MOUNT ONLY TO AN OUTL T BOX MARK D

ACC PTABL FOR FAN SUPPORT

All set screws must be checked and retightened where necessary before

installation.

Canadian Safety Tips

A. Carefully lift fan assembly onto mounting

bracket. Rotate fan so that the notch on

the ball engages the ridge in the

mounting bracket. This will allow hands-

free wiring. For wiring instructions please

refer to page 4 step #7.

2While the fan assembly is still on the

ground thread the safety cable through

the mounting bracket.

safety cable

mounting

bracket

plain

washer

safety cable

Set screw

3" lag

screw

Lift fan assembly and install the safety cable

directly to the building structure using the 3" lag

screw and plain washer provided. Before

proceeding to the next step make sure that the

cable is properly installed and will support

the fan weight. ake sure the screw

washer and safety cable are installed using

the order pictured above.

Feed motor lead wires through downrod/

canopy assembly and insert downrod into

motor yoke. Next, insert clevis pin through

yoke and downrod and secure with cotter

pin. (see inset) Tighten both yoke set

screws to further secure downrod.

Cotter

Clevis

Pin Set

Screws

Page 4 – Builder Supreme-English CUL

Note:

After installation, please refer to operation, maintenance and troubleshooting sections in this manual.

If your fan is packaged with a light kit or if you wish to install a separately purchased light kit,

please refer to the insert sheet titled: L

IGHT

NSTALLATION

INSTALLATION

WIRING OPTION WITH WALL SPEED CONTROL

Wall

control

Light Switch

Fan Switch

For control of fan and optional light from

wall location, follow diagram above.

NOTE: A professional electrician is

recommended for this type of installation.

*ATTACH BLU WIR

ONLY I F ATTACHING

LIGHT KIT WITH FAN

Secure with

twist-lock wire

connectors

(included)

STANDARD WIRING OPTION

Fiber

Washers

Shipping

Stabilizer

Tab

Raise the canopy up and align the two

holes in the canopy with the two holes

in the hanger bracket. Secure with two

5/32 x 1/2" screws provided.

CO BO-BLADE

Combo-Blades feature two high quality

finishes on one blade. Select the one

that best complements your decor, or

change the style with just a flip of the

blade.

For pullchain controls, follow diagram above.

ake sure that all exposed wiring is secured

inside wire nuts. Note: Wires from house may

vary in color and may not include ground

wire. After wiring is conplete, gently

push wires into junction box with wire

nuts pointing upward.

Attach blade brackets to blades using

the blade bracket screws and washers

provided.

Remove plastic shipping stabilizer tabs from

motor, if present. The screws, washers and

motor pads are pre-installed to the blade

holders. Attach blade assembly to motor

by tightening first screw one turn, then

tighten second screw securely. Then, go

back and tighten first screw securely.

Page 5 – Builder Supreme-English CUL

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these

installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be

remedied, or you are experiencing difficulty in installation, please call our Customer Service Center at the number printed on your parts list

insert sheet.

TROUBLESHOOTING GUIDE

1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: ake sure main power is turned off.

3. ake sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch is in the

middle.

4. ake sure that shipping stabilizer tabs have been removed from motor (see installation step #11).

1. Check to make sure all screws in motor housing are snug (not over tightened).

2. Check to make sure the screws which attach the fan blade holder to the motor are tight.

3. Check to make sure wire nut connectors in switch housing are not rattling against each other or against the

interior wall of the switch housing.

CAUTION: ake sure main power is turned off before entering switch housing.

4. If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are finger tight.

Check to be sure light bulb is tight in socket and not touching glass shade(s). If vibration persists from

glass, remove glass and install a 1/4" wide rubber band on glass neck to act as an insulator. Replace glass

and tighten screws against rubber band.

5. Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT USE a Solid

State variable speed control.

6. Allow "break-in" period of 24 hours. ost noises associated with a new fan will disappear after this period.

1. ake sure that the ridge of the mounting bracket engages the notch in the downrod ball. (See illustration in

Step #6 of Downrod ount installation).

2. Check that all blades are screwed firmly into blade holders.

3. Check that all blade holders are tightened securely to motor.

4. ake sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box

is mounted firmly to ceiling joist.

5. ost fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on

the ceiling above the tip of one of the blades. easure this distance as shown in Figure 1. Keeping measure

within 1/8", rotate the fan until the next blade is positioned for measurement. Repeat for each blade. If all

blade levels are not equal, you can adjust blade levels by the following procedure. To adjust a blade tip

down, insert a washer (not supplied) between the blade and blade holder at the screw closest to the motor

(Figure 2). To adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at the

two screws farthest from the motor (Figure 2).

6. If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the

weight and possibly result in smoother operation.

1. Check blue wire from fan to make sure it is connected to hot wire from house.

2. Check for loose or disconnected wires in fan switch housing.

3. Check for loose or disconnected wires in light kit.

4. Check for faulty light bulbs.

CAUTION: ake sure main power is turned off before entering switch housing.

1. If fan does not start:

2. If fan sounds noisy:

3. If fan wobbles:

Touching

Ceiling

Figure 1

Blade Tip Down:

Blade Tip Up:

Fan Blade

Figure 2

Blade Brackets

4. If light does not work:

SUGG ST D R M DY

TROUBL

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

CUSTO ER SERVICE CENTER:

2900 WEST SE INARY DR.

FORT WORTH, TEXAS 76133

1-800-519-4092

Page 6 – Builder Supreme-English CUL

9/18/98 REV. 0 CREATED ENGLISH CUL VERSION FOR BUILDERS SUPRE E

12/14/01 Rev.1 Changed to allow for preinstalled motor screws to blade holder. Changed customer service number

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5LD52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company MC1215 Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company 3BWR50XXD Series Fan Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR52XX Fan Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DVR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VLR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CU52XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR88XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HV52 F Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YK52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3STR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5RH52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MYR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Arcade 3ARR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GL66 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WFXX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LLR56 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Mach One Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BY52XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MMR54 D-L Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung