Monte Carlo Fan Company 3JVR44 Series Gebrauchsanweisung

Total fan weight

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

3JVR44XXX Series Fan

CUL Model NO. : 3JVR44XX

5.75 kg

12.65 lbs

Owner’s Guide and Installation Manual

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including

ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed

carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to

prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the ﬂoor

to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of 15.9 kg (35 lbs)

or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts

In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure (or the

ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert

foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. UC9020 manufactured by Rhine

Electronic Co., Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment

manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is required, the

product should be returned to an authorized service facility for examination or repair.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in damp locations. Install the fan under covered or enclosed patios or porches.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble). Remove the two outlet

box screws provided with the box,

aligning the holes of the mounting

bracket with the holes of the outlet box.

Reinstall the 2 outlet box screws

securely.

Install a blade bracket onto blade with a

blade bottom plate using set screws

provided. Repeat this process for

remaining blades.

Put motor assembly on a suitable area of

paper pulp.

Remove the blade set screws from

motor.

Install the blade assembly to motor using

the set screws. Tighten screws securely.

Repeat this process for remaining blade

assemblies.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Remove preassembled cross pin and

keeper pin from downrod. Keep parts.

Mounting bracket

Set screw

Set

screw

Blade bracket

Blade

Blade bottom plate

Downrod

Cross pin

Keeper pin

Yoke

7 8

10 11 12

Place downrod over canopy, canopy

bottom cap and yoke cover. Thread lead

wires and safety cable from motor

assembly through downrod.

Slip downrod into motor housing yoke,

aligning holes and install cross pin and

keeper pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the

cross pin, and then evenly tighten the

downrod set screws on motor housing

yoke.

Place yoke cover on top housing of fan.

Warning: Cross pin and keeper pin must

be installed securely, failure to install them

will result in serious injury.

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper than 20º. Longer downrod

may be necessary allowing the fan blades

to rotate without obstructions.

Safety cable must be installed into the

house structure using 3” lag screws,

washers, and lock washers provided,

required for outdoor applications and in

Canada (All fans installed in Canada), and

for USA fan and light kit combinations

over 35lbs.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Refer to page 6 for wiring,

installation and operation of Wall

controller. Do not operate the fan

or light until it is installed

completely

After making the wire connections, the

wires should be spread apart with the

grounded conductor and the

equipment-grounding conductor on one

side of the outlet box and ungrounded

conductor on the other side of the outlet

box. The splices after being made should

be turned upward and pushed carefully up

into the outlet box.

Downrod

Canopy

Canopy bottom cap

Keeper pin

Cross pin

Tab

Slot

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Black

White

Yoke cover

Grounded wire Ungrounded wires

To neutral wire

from house

Ground/Green

White

(Neutral)

Black

(Live)

To Wall Outlet Box

13 14 15

Partially loosen one and remove one

preassembled screw from mounting

bracket. Save screw.

Lift canopy up, aligning its keyhole slot

with the preassembled screw on

mounting bracket and twist clockwise to

lock in place. Reinstall the screw

removed and tighten all screws securely.

Attach canopy bottom cap onto canopy

by aligning its holes with the screws on

mounting bracket and ﬁx it with the

magnet which is embedded in the cap.

Setting the reverse switch in the down

position will result in downward airﬂow

and setting the switch in the up position

will result in upward airﬂow.

Note: Reverse switch must be set either

completely down or completely up for fan

to function. If the reverse switch is set in

the middle position, fan will not operate.

Reverse switch

Canopy bottom

cap

OFF

Operation

This wall controller provides 4 fan

speeds.(Fig.2)

1 - High - , 2 - Medium high , 3 -

Medium , 4 - Low , - Off.

Warning: Before proceeding, be sure to shut off electricity

at main switch or circuit breaker in order to avoid electrical

shock.

Note: Before installing the wall transmitter, place it in OFF

position. (Fig.2)

Make series-wound connection for the wall controller with

HOT wire from house and lead wires from fan.

Connect the black wire marked “AC IN L” from wall controller

to the HOT wire from house and then connect the black wire

marked “TO MOTOR L” of wall controller to the fan lead wire

from fan in outlet box.

Connect green/yellow grounded wire to grounded wire from

outlet box.

Install the wall controller to outlet box using machine screws

provided.

Attach wall plate to wall control unit with screws provided.

(Fig.1)

Black(AC IN L)

Black (TO MOTOR L)

Green/Yellow (Grounding)

Outlet box

Fig.1

Fig.2

Wall controller

WHITE (Neutral)

BLACK (Live)

BLACK

120V/60HZ

Power supply

Wall plate

Troubleshooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning

and lock the service panel to prevent the power from being switched back on accidentally. If the service panel

cannot be locked to prevent the power from being switched on accidentally, securely fasten a warning sign to the

service panel.

1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in switch housing.

CAUTION

either way. Fan will not operate when switch is in the middle.

4. If this fan uses a remote controller, make sure dip switches are in the correct setting

and make sure the battery works.

1. Check to make sure all screws in motor housing are snug (not over tightened).

2. Check to make sure the screws which attach the fan blade holder to the motor are tight.

3. Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION

4. Check to be sure light bulb is tight in socket and not touching the glass shade.

5. Some fan motors are sensitive to signals from Solid State variable speed controls.

6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will

disappear after this period.

1. If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2. Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4. Check that all blade holders are tightened securely to motor.

5. Most fan wobble problems are caused when blade levels are unequal. Check this level

by selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceiling. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6. If blade wobble is still noticeable, interchanging two adjacent blades can redistribute the

weight and possibly result in smoother operation.

If the above steps do not eliminate the wobble problem, you will need to dynamically

balance your fan with balancing kit provided.

1. Check blue wire from fan to make sure it is connected to hot wire from house.

2. Check for loose or disconnected wires in fan switch housing.

3. Check for loose or disconnected wires in light kit.

4. Check for faulty lightbulb and make sure bulb is tight in socket.

5. Remove light kit and check the plug connections if they are present.

6. If this fan uses a remote controller, make sure dip switches are in the correct setting

and make sure the battery works.

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Jan.2022

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5PAR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLNSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5FWR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AKR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8TNR56 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company MCM360 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ADR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MNLR56 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OR52XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Centro Max 5CQM52-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DOR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TSR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CO52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YK52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GIR54XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ATR44 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIC52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LNR52 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3BTR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YK60 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung