Monte Carlo Fan Company 5CQM52 Series Gebrauchsanweisung

Total fan weight

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

5CQM52XXX Series Fan

CUL Model NO. : 5CQM52XXX

8.7 kg

19.14 lbs

Owner’s Guide and Installation Manual

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the

building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any unveriﬁed solid state fan speed control device, or

variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

OFF

Preparation

Warning: Before starting assembly of this product, please disconnect

power to area and familiarize yourself with the safety information

provided on page 2.

Determine mounting method to use.

A - Downrod Mount

B - Angle Mount

Important: If using the angle mount, check

to make sure the ceiling angle is not steeper

than 30º.

Important: If using the angle mount, make sure open end of mounting

bracket is installed facing the higher point of the ceiling.

C - Flushmount

Note: Flushmount is not available with vaulted ceiling.

Installation Instruction

Before you begin installing the fan, Switch power off at Service panel

and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a warning device, such as a tag, to the

service panel. (Fig. 1)

Before installing this fan make sure the outlet box is properly installed to

the house structure. To reduce the risk of ﬁre, electric shock, or

personal injury, mount to outlet box or supporting system acceptable

for fan support (Mounting must support at least 35 lbs). (Fig. 2)

Use metal outlet box suitable for fan support and use only the screws

(and may be with ﬂat washers and lock washers) provided with the outlet

box (must support 35 lbs). Before attaching fan to outlet box, ensure

the outlet box is securely fastened by at least two points to a structural

ceiling member (a loose box will cause the fan to wobble). Remove the

two outlet box screws provided with the box, aligning the holes of the

mounting bracket with the holes of the outlet box. Reinstall the 2 outlet

box screws securely. (Fig. 2-1)

Fig. 1

Fig. 2 Fig. 2-1

Mounting

bracket

Installation Instruction (Downrod Mount)

Partially loosen downrod set screws from yoke at top of motor

assembly.

Remove keeper pin and cross pin from yoke, and save for later use.

Place downrod over canopy and yoke cover. Thread lead wires and

safety cable from motor assembly through downrod.

Slip downrod into motor housing yoke, aligning holes and install cross

pin and keeper pin.

Insert cross pin through yoke and downrod until point appears on the

other side, and insert keeper pin on cross pin.

Pull the downrod up tight against the cross pin, and then evenly tighten

the downrod set screws on motor housing yoke. (Fig. 3)

Warning: Cross pin and keeper pin must be installed securely, failure

to install them will result in serious injury.

Install ball end of downrod into mounting bracket opening. Align

(engage) slot on ball with tab on mounting bracket.

Warning: Failure to align slot on ball with tab may result in serious

injury. (Fig. 4)

Fig. 3

Fig. 4

Tab

Slot

Canopy

Lead wires and

Safety cable

Motor assembly

Cross pin Keeper pin

Yoke

Downrod

Set screw

電容器

Yoke cover

電容器

Installation Instruction (Flushmount)

Remove canopy cover by turning counterclockwise. There are 6 holes

on the bottom of the canopy, 3 of them are larger. (Fig. 5)

Thread lead wires and safety cable through canopy. Place canopy over

yoke, aligning larger holes in canopy with the 3 existing screws on top

of motor housing. Install 3 screws and 3 lock washers (these screws

and lock washers will be located in the hardware pack) into the

remaining holes. Tighten all screws securely. (Fig. 5-1)

To prepare the fan for wiring, hang fan onto mounting bracket by

sliding the canopy over the mounting bracket hook (Use one of

non-slotted holes on the rim of the canopy). (Fig. 5-2)

Safety Cable Installation

For Canadian installation and for USA fan and light kit combinations

over 35 lbs, in both ﬂush and downrod modes the safety cable must

be installed into the house structure beams using 3” lag screws,

washers and lock washers provided. Make sure that when the safety

cable is fully extended the lead wires are longer than the cable and no

stress is placed on the lead wires. (Fig. 6)

Note: If Installing The Secondary Support Safety Cable in the U.S., Do Not

Remove Knockouts In The Outlet Box.

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Fig. 5-1

Fig. 6

Fig. 5-2

yoke

Canopy

Screws

Canopy

Hook

Lead wires and

Safety cable

電容器

Fig. 5

Canopy cover

Wiring

Warning:

Make sure main power is turned off before making

wiring.

Make wire connections as indicated. Connect Black and Blue

wire from fan to Black (Hot) wire from house. Connect White

wire from Fan to White (Neutral) wire from house. Connect all

green grounded wires from fan to Grounded wire from

House. Make sure that no ﬁlaments are outside of the wire

connectors. (Fig. 7)

After making the wire connections, the wires should be

spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet

box and ungrounded conductor on the other side of the

outlet box. The splices after being made should be turned

upward and pushed carefully up into the outlet box.

For control of fan and light separately from wall location,

follow diagram as shown. (Fig. 7-1)

Note

: A professional electrician is recommended for this

type of installation.

Note

: Wrap each wire connector separately with electrical

tape as an extra safety measure.

Canopy Installation

Partially loosen 2 of the set screws on mounting bracket

corresponding to the slotted holes on the canopy upper ring.

Remove the other 2 set screws. Save screws.

Raise canopy to mounting bracket, aligning loosened screws

in mounting bracket with slotted holes in canopy. Twist

canopy to lock. Reinstall screws (with washers) that were

previously removed and then tighten all screw securely. (Fig.

8, Fig. 8-1)

Power supply

Black

white

Grounding/Green

Fan

Light Blue

Black

Wall controller

Wiring Option with Wall Controller

Fig. 7

Fig. 7-1

Fig. 8

Mounting bracket

Fig. 8-1

Wall Switch

White

Black

Power

Line

Blue

Grounded/

Green

Canopy

Set screws

Canopy

Set screws

Canopy cover

Downrod mount

Flush mount

電容器

Fig. 9

Fig. 10 Fig. 10-1

Fig. 11

Reverse switch

Screws

Blade

Blades bracket

Screws

Washers

Set screws

Install fan pull chain to preassembled pull chain on fan. Pull chain

provided. (Fig. 11)

Forward/Reverse switch setting

Setting the reverse switch on the left hand side will result in

downward airﬂow and setting the switch on the right hand side will

result in upward airﬂow.

Note: Reverse switch must be set either way completely. If the

reverse switch is set in the middle position, fan will not operate.

(Fig. 11)

Operation and Maintenance

Refer to operation and maintenance on the second page of parts

list.

Blade installation

Install blade bracket with blade by 3 blade screws and washers provided.

Tighten screws securely. Repeat this process for remaining blades. (Fig. 9)

Remove shipping stabilizers from motor assembly.

Install the blade assembly to motor using the preinstalled screws. Tighten

screws securely. Repeat this process for remaining blade assemblies. (Fig. 9)

Note: Tighten blade bracket screws twice a year.

Switch housing installation and wiring

Loosen 2 and remove one set screws from the plate on motor, keep screw.

Attached top switch housing onto the plate on motor, aligning its keyhole

slots with the set screws on the plate and twist clockwise until tight. Reinstall

the screw which is just removed and tighten all screws securely. (Fig.10)

Attach capacitor onto switch housing by preadhered double-sided foam tape

as shown.

Connect the plug from fan to the plug from switch housing, aligning the claps

and make sure plugs connected securely. (Fig. 10-1)

Remove 4 set screws from top switch housing, keep screws.

Align the long slot on top switch housing with the reverse switch on switch

housing, and then install the switch housing onto the fan with the 4 side

mount screws which were just removed.

Top switch housing

Switch housing

Capacitor

Plate on motor

Set screws

電容器

shipping stabilizers

Long slot

Reverse switch

Pull chain

Trouble Shooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION

either way. Fan will not operate when switch is in the middle.

4.If this fan uses remote controller, make sure dip switches are setting properly and make

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION

4.Check to be sure light bulb is tight in socket and not touching the glass shade.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

6.Allow "break-in" periodof 24 hours. Most noisesassociated with a new fan will disappear

after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4.Check that all blade holders are tightened securely to motor.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

If the above steps do not eliminate the wobble problem, you will need to dynamic balance

your fan with balancing kit provided.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulb and make sure bulb is tight in socket.

5.Remove light kit and check the plug connections if they are present.

6.If this fan uses remote controller, make sure dip switches are setting properly and make

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Jun.2019

Jun.2020 branding

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3VNR52XXD series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Dylan 3DYR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CNHSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CQR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LCM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AHR60 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3FSR52 series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CO52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Mini 4MC20BS Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HLR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TV52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Mach One Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR70 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ALMSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5RDR Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GL52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5UPR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Hicks 3HCKR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YK52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3RZHR44 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung