Monte Carlo Fan Company 5RDR Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attac sales receipt to t is card and retain as your proof of purc ase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To register your fixture, please visit our website www.montecarlofans.com

5RDR Series Fan

Total fan weig t

UL Model No. : AC-212-003

27.75 kgs

61.05 lbs

WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G

READ A D SAVE THESE I STRUCTIO S

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA

70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

31.8 kg (70 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do ot Re-

move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to

the building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RC manufac-

tured by Rhine Electronic Co., Ltd.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

ever place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Warning-Risk of fire, electric shock, or personal

injury. The fan in this box may be either directly

supported from a structural framing member of

a building and/or may be mounted to an outlet

box or fan brace marked acceptable for fan sup-

port of of 31.8 kg (70 lbs) or less. Most outlet

boxes commonly used for the support of lumi-

naries may not be acceptable for fan support

and may need to be replaced. Consult a qualified

electrician if in doubt.

Remove the 6 screws attaching the

Mounting neck from the mounting

plate. Retain the 6 screws for re-as-

sembly.

Secure mounting plate directly to a joist from

the buliding structure. Use only the appropriate

wood screws and washers included with your

fan.

Caution: Wood screws must go through into

the building joist.

Note:If Installing It In The U.S., Do Not Re-

move Knockouts In The utlet Box

utlet box

Mounting

Plate

Wood

Screws

BUILDING STRUCTURE METH D

Twist mounting neck and remove

from mounting plate.

Install the mounting Plate to approved fan

brace or outlet box, use only the hardware pro-

vided with the fan brace or outlet box.

6FAN BRACE AND UTLET B X METH D

For Installation in The U.S. only

Screws 2 on each end

and 1 on each side.

Lower upper glass disk onto fan housing and

align 3 holes in glass with 3 holes in fan hous-

ing.

Lift mounting neck to mounting Plate and align

screws.

Secure mounting neck to the mounting plate

with 6 screws to become a complete mounting

bracket.

Install 3 screws to hold glass to fan

housing. Do not overtighten as this

could crack the glass.

Pull lead wires and safety cable out

from the yoke about 3”.

Raise lead wire, safety cable, and

downrod up and align with slot for

pin in bottom of arch yoke. Push pin

into hole in downrod. After putting

in pin don’t twist downrod. Make

sure pin is fully engaged in slot.

Tighten set screws to hold downrod

securely in the arch yoke.

Place downrod into the arch yoke and

align the slot in arch yoke and the

hole in the downrod.

Place arms over the fan housing.

Make sure the arms with electrical

connection plugs are next to the

plugs on the fan housing.

Remove pin from downrod and save

for later step 14. Push the yoke cover

onto downrod. Thread lead wires and

safety cable through the downrod.

Close up for showing tab and screw

holes of fan body to place arch arms

over for arch installation.

Align holes in arch arm and slot for

tab with holes and tab on fan body.

Start all screws in the arch arm

brackets.

Install decorative cap.

Tighen the 3 screws holding the arch

arms securely.

Thread leadwires and safety cable

through the canopy. Place canopy

over the downrod.

Push the yoke cover down into place.

Plug in electrical connections there

are 2 double plugs from arch assem-

bly one for the fan and one for the up

and down lights.

Install 6 x 15 watt candelabra tor-

pedo shape bulbs.

Tighen all 6 screws for arch arms se-

curely.

Install arch mount by using clips in

plastic bag. Place clip through tab

and fasten securely.

Set dip switches on the Remote Transmitter and

Remote Receiver to the same settings. This must

be done so the units will communcate properly. If

you have other fans you can set to control from

one transmitter by setting both receivers the same

as the transmitter. If you have more than one fan

with remote. You can set the dip switches to differ-

ent positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches

Hang assembled fan from the mounting bracket.

Make sure the fan is hanging straight. Rotate

fan until the tab on the Mounting bracket en-

gages the slot on the Downrod Ball. This must

be done to prevent the fan body from rotating

when the blades are in motion.

Rotate slide on mounting bracket till it stops so

the screw holes will align for 2 canopy screws in

hardware pack. Tighten the 2 screws securely.

These will lock slide in place till ready to mount

canopy. (step 34)

For Canadian installation and for USA fan and light

kit combinations over 35 lbs, in both flush and

downrod modes the safety cable must be installed

into the house structure beams using 3” lag screws,

washers and lock washers provided. Make sure that

when the safety cable is fully extended the lead

wires are longer than the cable and no stress is

placed on the lead wires.

Note:If Installing The Secondary Support Safety

Cable in the U.S., Do Not Remove Knockouts In The

utlet Box.

30 Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw

lock

washer

Lift Canopy to ceiling aligning the key hole slots

with the screws on the bottom of the Mounting

bracket. Rotate the canopy Counter Clockwise

to lock in place. Tighten the screws to secure

the Canopy. See inset for Keyhole shape

Attach blade brackets to blades using

the blade bracket screws and wash-

ers provided.

Install all 5 fan blade assemblies to

the motor as shown above. Tighten

screws securely.

Make wire connections to power source using

wire nuts provided. Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on the

other side of the outlet box.

white

black

Make wiring connections as indicated above.

White from fan to white from remote marked

N. range from fan to range from remote

marked Light/up. Blue from fan to blue from

remote marked down light. Black from fan to

Black from remote marked L. White from

house to white from remote marked AC N .

Black from house to Black from remote

marked AC L. Connect all green ground wires

to Ground wire from House.

orange

blue

Green

white

black

House

Fan

Loosen 2 screws and remove one and

save it. Place plate’s key slotted holes

over the 2 screws loosened and twist

into place. Replace removed screws

and tighten all 3.

Attach switch housing to fan using

the three screws provided.

Plug 9 pin wire connections together.

Remove cover by snaping off from top or bot-

tom. Remove battery cover. Install 12V battery

into wall remote. Duracell MN21 / Eveready A23

/ GP 23A all 12V.Attach cover of remote by plac-

ing over buttons and snap the battery cover in

place.

Place face plate over battery compartment and

buttons. Place remote over 2 pins on front

cover. Attach cover of remote by placing over 4

pins and snaping into place.

HAND HELD INSTALL

Install wall control unit to outlet box

using machine screws provided.

Attach front cover to wall control

with screws provided. Snap battery

cover in place.

WALL M UNT INSTALL

Remote Control Transmitter Features:

FAN SPEED Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for

high. To turn fan off press square”.

LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn off

press once quickly while light is on. To dim light hold down button “light dimmer”.

The light will cycle from bright to dim to bright until button is released. Light will

maintain last setting if turned off.

FORWARD/REVERSE Depress rev button allow a few seconds for remote to

change rotation direction with fan running.

HIGH SPEED

MEDIUM SPEED

LW SPEED

FAN FF SETTING

(Turns fan off only)

FAN REVERSE

(Press once to

change direction of

the fan)Fan must be

running to reverse.

UPLIGHT N/ FF SET-

TING AND DIMMER

(Press and hold to dim

light infinitely)

LED LIGHT

D WNLIGHT N/ FF

SETTING AND DIMMER

(Press and hold to dim

light infinitely)

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Check to make sure the dip switches from the transmitter and receiver are set on the

same frequency.

CA TION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CA TION: Make sure main power is turned off before entering switch housing

and canopy.

4.Some fan motors are sensitive to signals from Solid State variable speed controls.

DO NOT SE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction

box and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is

positioned for measurement. Repeat for each blade. If all blade levels are not equal, you

can adjust blade levels by the following procedure. To adjust a blade tip down, insert a

washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CA TION: Make sure main power is turned off before enterin switch housing and

canopy.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not

work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any

faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing

difficulty in installation, please call our Customer Service Center at the number printed on your parts list

insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service

disconnecting means to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Trouble Suggested Remedy

Mar.2012 New format

May.2013 Update for CUL regulation

Andere Handbücher für 5RDR Series

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3VTR52/38 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MO52 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3STMSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VMR72 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4BFR54 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ALR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR60XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company MC5B241 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TSR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CNR52 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TAHR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ALR56-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3FSR52 series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GP60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CQM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52RZWD-V1 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CO52RB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ATR44XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MQ60XX Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung