Monte Carlo Fan Company 5CU52WH Gebrauchsanweisung

5777 U425 U432 U

Owner’s Guide and Installation Manual

5CU52XX Series Fan

UL Model No. : AC-AC-303OD

Total fan weight

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as your proof of purchase

To register your fixture, please visit our website www.montecarlofans.com

9.6 kgs

21.12 lbs

7/1/2013

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conduc-

tor on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of 15.9

kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the

building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in wet locations when installed in a GFCI protected branch circuit.

Cautions and Warnings

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVETHE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Steplad-

der and Wire Strippers

7/1/2013

Before you begin installing the fan, Switch

power off at Service panel and lock service

disconnecting means to prevent power

from being switched on accidentally. When

the service disconnecting means cannot

be locked, securely fasten a prominent

warning device, such as a tag, to the

service panel.

Before installing this fan make sure the

outlet box is properly installed to the house

structure. To reduce the risk of re, electric

shock, or personal injury, mount to outlet

box or supporting system acceptable for fan

support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan support

and use only the screws provided with the

outlet box (must support 35 lbs). Before

attaching fan to outlet box, ensure the outlet

box is securely fastened by at least two points

to a structural ceiling member ( a loose box

will cause the fan to wobble). Remove the

two outlet box screws provided with the box,

aligning the holes of the mounting bracket

with the holes of the outlet box. Re-install the

2 outlet box screws securely.

Loosen 2 screws on yoke to

allow down rod to slip into

yoke.

5 6

Place canopy over downrod.Remove keeper pin and cross

pin from yoke, and save for

later use.

Thread the leadwires and

safety cable through the

downrod.

Place canopy bottom cap over

downrod and then place yoke

cover over downrod as shown.

Insert downrod into the yoke on top of

fan body. Align the hole in the downrod

with the hole in the yoke. Insert cross

pin through yoke and downrod until

point appears on the other side.

7/1/2013

Install keeper pin.

Tighten the 2 set screws on

the yoke, once the down rod

is in place.

Loosen one and remove one

preassembled screws from

mounting bracket. Save

screw for later use.

Hang assembled fan from the mounting

bracket installed to ceiling in previous

step. Make sure the fan is hanging

straight. Rotate fan until the tab on the

Mounting bracket engages the slot on

the Downrod Ball. This must be done to

prevent the fan body from rotating when

the blades are in motion.

Connect black and blue wire from fan to

Black or (Hot) wire from house. Connect

White wire from Fan to White (Neutral)

wire from house. Connect Ground leads

from mounting bracket and downrod

to Ground lead from house. Refer to

Safety Tips section of manual.

Make wire connections to power source

using wire nuts provided. Make sure that

no liments are outside of the wirenut. After

making the wire connections, the wires should

be spread apart with the grounded conductor

and the equipment-grounding conductor on

one side of the outlet box and ungrounded

conductor on the other side of the outlet box.

The splices after being made should be turned

upward and pushed carefully up into the outlet

box.

17 18

Lift canopy up, aligning its keyhole

slot with the preassembled screw

on mounting bracket and twist till

lock. Install the screw removed

in step 12. Tighten all screws

securely.

Attached canopy bottom cap

onto canopy by aligning its

notches with the screws on

mounting bracket and twist

clockwise till tight.

Supply

circuit

For Canadian installation and for USA fan and light

kit combinations over 35 lbs, in both flush and

downrod mode the safety cable must be installed

into the house structure beams using the 3” lag

screws,washers, and lock washers. provided. Make

sure that when the safety cable is fully extended

the leadwires are longer than the cable and no

stress is placed on the leadwires.

Note

: If Installing The Secondary Support Safety

Cable in the U.S., Do Not Remove Knockouts In The

Outlet Box.

Lag screw

Safety cable

Washer

Lock washer

Lag screw

Safety cable

Safety cable installation

7/1/2013

Install blade bracket with blade by

3 blade screws provided. Tighten

securely. Repeat this process for

remaining blades.

Note: Make sure the side with a label

“This side up” is installed upward.

Loosen 2 and remove 1

preassembled screws from the

plate on motor. Save screw for

later use.

Check motor for shipping stabilizers

and remove if present. Install the blade

assembly to motor using the screws

pre-installed. Tighten screws securely.

Repeat this process for remaining blade

assemblies.

Place switch housing over wire harness

from motor. Attached switch housing

on to the plate on motor, aligning the

keyhole slots with the preassembled

screws on the plate. Twist clockwise till

lock. Install the screw removed in step

22. Tighten all screws securely.

Connect plug from fan to plug

from switch housing. Make sure

the plugs are hooked together.

25 27

Remove 3 preassembled screws

from switch housing cover. Save

screws for later use.

Attach capacitor onto switch

housing by preadhered double-

sided foam tap as shown.

Attach switch housing cover onto

switch housing by aligning the long

slot on switch housing cover with

the reverse switch preassembled on

switch housing as shown.

Hook

Place blade bracket onto the

front side of blade by aligning

the 3 holes on blade as

shown.

Shipping

stabilizer

7/1/2013

Install switch housing cover with

the screws removed in step 26.

7/1/2013

Trouble Shooting

If you have difculty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difculty in

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3.If this fan uses manual forward/reverse switch, make sure the switch is pushed rmly

either way. Fan will not operate when switch is in the middle.

4.If this fan uses remote controller, make sure dip switches are setting properly and make

sure battery is effective.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Check to be sure light bulb is tight in socket and not touching the glass shade.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to

ceiling junction box and junction box is mounted rmly to ceiling joist.

3.Check that all blades are screwed rmly into blade holders.

4.Check that all blade holders are tightened securely to motor.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulb and make sure bulb is tight in socket.

5.Remove light kit and check the plug connections if they are present.

6.If this fan uses remote controller, make sure dip switches are setting properly and make

sure battery is effective.

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Mar.2012 new format

Jul.2013 Update for CUL regulation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5MMR54 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TTHR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIW52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4BN44WHD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4BFR54 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5UPR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LPR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LLR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 25003 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR52XX Fan Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 14PRR72 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TSR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CQR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HLR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4ICR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WFXX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AB52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24BS Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung