Monte Carlo Fan Company 4BFR54 D-V1 Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Total fan weight with light

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

4BFR54XXD-V1 Series Fan

cETL Model NO. : 4BFR54

9.7 kgs

21.34 lbs

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the

building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To Reduce The Risk Of Electric Shock, This Fan Must Be Installed With a general use, isolating Wall Control/Switch.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. UC7067RY manufac-

tured by Rhine Electronic Co., Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable

speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked, and re-tightened where necessary, before installation.

Note: Suitable for use in damp locations.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble). Remove the two outlet

box screws provided with the box,

aligning the holes of the mounting

bracket with the holes of the outlet box.

Reinstall the 2 outlet box screws

securely.

Remove cross pin from yoke at top of

motor assembly. Keep it for later use.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Place downrod over canopy and yoke

cover. Thread lead wires and safety cable

from motor assembly through downrod.

Slip downrod into motor housing yoke,

aligning holes and Reinstall the cross pin.

Insert cross pin through yoke and downrod

and then fasten it with screwdriver.

Pull the downrod up tight against the

cross pin, and then evenly tighten the

downrod set screws on motor housing

yoke.

Place yoke cover on top housing of fan.

Warning: Cross pin must be installed

securely, failure to install it will result in

serious injury.

Mounting bracket

Canopy

Yoke cover

Downrod

Cross pin

Set screw

Downrod

Yoke

Cross pin Setscrew

Yoke

7 8 9

10 11 12

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper

than 20º.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 1.5” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Set dip switches on the Remote

Transmitter and Remote Receiver to the

same settings. This must be done so the

units will communicate properly. If you

have other fans you can set to control

from one Transmitter by setting

receivers the same as the Transmitter. If

you have more than one fan with remote,

you can set the dip switches to different

positions to have separate control.

Make wiring connections using wire

connectors provided as indicated above.

White from fan to White from remote

marked N. Black from fan to Black from

remote marked L. Blue from fan to Blue

from remote marked FOR LIGHT. White

from house to White from remote marked

AC N. Black from house to Black from

remote marked AC L. Connect all green

grounded wires to Grounded wire from

House. Make sure that no ﬁlaments are

outside of the wire connectors.

Insert the remote receiver into mounting

bracket.

Loosen one and remove one

preassembled screw from mounting

bracket. Save screw.

Lift canopy up, aligning its keyhole slot

with the preassembled screw on

mounting bracket and twist

counterclockwise to lock in place.

Reinstall the screw removed in step 11

and tighten all screws securely.

SAFETY CABLE INSTALLATION

Dip switches

Lag screw

Safety cable

Washer

Lock washer

Tab

Slot

Wall switch

Black

White

Ground/Green

White

White Black

Black

Receiver

Blue

Mounting bracket Canopy

Set screw

13 14 15

16 17 18

Insert the short blade into the lower

couplers and then insert the long blade

into upper couplers on the hubs. Repeat

this process for the remaining blades

assemblies on the other side of the hubs.

Note: Make sure the screw holes in blade

frames are installed upward.

Loosen 2 and remove 1 preassembled

screw from the plate on motor. Save

screw for later use.

Place light pan over the lead wires and

attach it onto the plate on motor.

Align the keyhole slots on the light pan

with the preassembled screws on the

plate on motor. Twist clockwise till lock.

Reinstall the screw removed in step 15.

Tighten all screws securely.

Remove 3 preassembled screw from the

light pan. Save screws for later use.

Connect white wire from fan to white wire

from LED light ﬁxture and then connect

black (or blue) wire from fan to blue (or

black) wire from LED light ﬁxture.

Attach LED light ﬁxture onto the light pan,

aligning the holes on the LED light kit with

the screw holes on light pan. Reinstall the

screws removed in step 17. Tighten all

screws securely.

Caution: Tuck the lead wires into the

plate on socket assembly as shown in

inset and make sure the light lead wires

are not pinched between the light pan and

the LED light ﬁxture.

Align the screws holes in blade frame and

the holes in the coupler and then ﬁx the

blades in the couplers with set screws

provided.

Long blade

Short blade

Lower coupler

Upper coupler

Light pan

Screw holes

Plate on motor

LED light ﬁxture

22 23 24

20 21

Attach glass by locating dimples in light

ﬁxture with the groves in glass and

twisting clockwise till tight.

Setting the reverse switch in the left hand

side will result in downward airﬂow and

setting the switch in the right hand side

will result in upward airﬂow.

Note: Reverse switch must be set either

completely LEFT or completely Right for

fan to function. If the reverse switch is set

in the middle position, fan will not

operate.

Remove battery cover. Install 12V battery

into wall remote. Duracell MN21 /

Evereday A23 / GP 23A all 12V. Attach

cover of remote by placing over buttons

and snap the battery cover in place.

Place battery cover over battery

compartment and buttons. Place remote

over 2 pins on front cover. Attach cover

of remote by placing over 4 pins and

snapping into place.

Install wall control unit to outlet box using

machine screws provided.

Attach front cover to wall control unit with

screws provided. Snap battery cover in

place

Right hand side

(Reverse)

Left hand side

(Forward)

Reverse switch

Battery cover

Battery

HAND HELD INSTALL WALL MOUNT INSTALL

Glass

FAN SPEED: Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan off press square”.

LIGHT DIMMER: To turn light on, press light dimmer once quickly. To turn off press once quickly while light is on. To dim light

hold down button “light dimmer”. The light will cycle from bright to dim to bright until button is released. Light will maintain last

setting if turned off.

Note: If not using for long periods of time, remove battery to prevent damage to remote transmitter, and store the remote

transmitter away from excess heat or humidity

Remote Control Transmitter Features

MEDIUM SPEED

HIGH SPEED

LED LIGHT

LOW SPEED

FAN OFF SETTING

(Turn fan off only)

LIGHT ON/OFF SETTING

AND DIMMER (Press and

hold to dim light infinitely)

Trouble Shooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION

either way. Fan will not operate when switch is in the middle.

4.If this fan uses remote controller, make sure dip switches are setting properly and make

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION

4.Check to be sure light bulb is tight in socket and not touching the glass shade.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

6.Allow "break-in" periodof 24 hours. Most noisesassociated with a new fan will disappear

after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4.Check that all blade holders are tightened securely to motor.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

If the above steps do not eliminate the wobble problem, you will need to dynamic balance

your fan with balancing kit provided.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulb and make sure bulb is tight in socket.

5.Remove light kit and check the plug connections if they are present.

6.If this fan uses remote controller, make sure dip switches are setting properly and make

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Jan.2014

Apr.12.14, Change light lead wires from fan to be black and white from blue and white

Jan.2018 change CUL to cETL

Jun.2019 change to LED light

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 4BN44WHD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ALMSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MB52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SLR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 25003 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5YM52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3BvR52XXd-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ASPR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ML52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LNR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVDC52D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MYR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3OWR60D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 14PRR62XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52XXN Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Essex 5ESR54 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Discus Trio Max 3DIR58 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SU54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DVR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VNR52XXD series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ED56WAD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI44 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PPR54XX Technisches Dokument

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung