Monte Carlo Fan Company 5CY60XX Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach sales receipt to this card and retain as your proof of purchase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To re ister your fixture, please visit our website www.montecarlofans.com

5CY60XX Series Fan

Total fan wei ht

UL Model No. : AC-570F811

14.58 kgs

32.08 lbs

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

ake sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, ount To Outlet Box arked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use ounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in wet locations when installed in a GFCI protected branch circuit.

Note: Use only with light kits marked suitable for use in wet locations.

Cutomer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, S witch

power off at Service panel and lock service dis -

connecting means to prevent power from being

switched on accidentally. When the service dis -

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Remove keeper from pin. Remove

pin, replace keeper and save.

Thread wire through downrod with

canopy and yoke cover assembled

onto downrod.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per -

sonal injury, mount to outlet bo x or supporting

system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet bo x is securely

fastened by at least two points to a structur al

ceiling member ( a loose bo x will cause the fan

to wobble). Use only the screws provided

with the outlet box.

Loosen the 2 set screws in y oke for

downrod to slip into yoke.

Insert downrod into motor yoke.

Next, insert clevis pin through y oke

and downrod.

Tighten both yoke set screws to fur-

ther secure downrod.

Secure with cotter pin.

Carefully lift fan assembly onto mounting

bracket. Rotate fan so that the notch on the

ball engages the ridge in the mounting br acket.

This will allow hands-free wiring.

Install 3 screws and washers per

blade and tighten securely. Repeat

for all 5 blades. The blades will ha ve

a label showing this side up on each

blade.

Make wire connections to power source

using wire nuts provided. Make sure that

no filiments are outside of the wirenut.

After making the wire connections, the

wires should be spread apart with the

grounded conductor and the equipment -

grounding conductor on one side of the out -

let box and ungrounded conductor on the

other side of the outlet bo x.

For pullchain controls, follow diagram above.

Make sure that all exposed wiring is secured

inside wire nuts. Note: Wires from house ma y

vary in color and ma y not include ground wire.

After wiring is conplete, gently push wires into

junction box with wire nuts pointing upw ard.

Refer to point 3 of safet y tips.

15 House Fan

Black

White

Green

Black

White

Green(downrod)

Green(Bracket)

Blue

For control of fan and optional light from w all

location, follow diagram above. NOTE: A profes-

sional electrician is recommended for this t ype

of installation.

Light Switch

Fan Switch

Wall

Control

Remove screws from stabilizer plate

on bottom of fan motor.

10 11

Remove stabilizer plate you will not

need this plate.

For Canadian installation and for US A fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be

installed into the house structure beams using

the 3” lag screws,washers, and lock washers.

provided. Make sure that when the safet y cable

is fully extended the leadwires are longer than

the cable and no stress is placed on the lead -

wires.

13 Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw

lock

washer

Loosen one and remove one preassem-

bled screw from mounting bracket.

Save screw. Lift canopy up, aligning its

keyhole slot with the preassembled

screw on mounting bracket and twist

clockwise to lock in place. Re-install the

removed screw and tighten all screws

securely.

Remove 4 screws and save to install

switch housing.

Install switch housing plate b y twist-

ing plate with key hole slots into

place. Replace screw removed and

tighten the 3 screws securely.

Connect plug from fan to switch

housing plug. Match the color strips

on the plugs.

Loosen 2 screws with key slots and

remove 1 screw without slot from

motor plate and save screw.

The screws, washers, and motor

pads are pre-installed to the blade

holders. Attach blade assembly to

motor and tighten screws securely.

Black capacitor box needs to be

stuck to the switch housing. Not

being attached can cause motor

noise.

Remove twin adhesive tape from the

black capacitor as shown above.

Place and press firmly on the capaci -

tor to stick it to the switch housing.

Be sure it is secure.

Install the switch housing using the 4

screws previously removed.

Setting the reverse switch in the

left hand side will result in down-

ward airflow and setting the

switch in the right hand side will

result in upward airflow.

Reverse

switch

1.Check main and branch circuit fuses or circuit break ers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Make sure that any shipping stabilizer has been removed from motor.

CAUTION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not o ver tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not r attling against each

other or against the interior w all of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State v ariable speed controls. DO

NOT USE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canop y engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor .

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction bo x

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade lev els are unequal. Check this lev el by

selecting a point on the ceiling abo ve the tip of one of the blades. Measure this distance

from blade tip to ceilng. K eeping measure within 1/8", rotate the fan until the next blade is

positioned for measurement. Repeat for each blade. If all blade lev els are not equal, y ou can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a w asher

(not supplied) between the blade and blade holder at the screw closest to the motor . To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at

the two screws farthest from the motor. Reverse the position of the w asher if blades mount

from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side b y side) blades can

redistribute the weight and possibly result in smoother oper ation.

1.Check wire from fan to mak e sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

1. If fan does not

start:

3. If fan wobbles:

4. If light does not

work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it ma y be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors ma y be mistaken for defects. If y ou experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or y ou are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on y our parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis -

connecting means to prevent power from being switched on accidentally. When the service dis -

connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Trouble Suggested Remedy

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5MYR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DH52 series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AZR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42RB Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SH54XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3OBSHR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3BRYSM60D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AB52XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DOR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3FSR52 series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4SBWR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MO52XXO-L series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CLR66XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LPR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5RH52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MNLR56BSD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DKR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DH52 Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung