Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach sales receipt to this card and retain as your proof of purchase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To re ister your fixture, please visit our website www.montecarlofans.com

5TQ52XXD-L Series Fan

Total fan wei ht with li ht kit

UL Model No. : AC-552

10.1 kgs

22.22 lbs

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO ERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999), including

fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the

outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed carefully up

into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the

trailing edge of the blade.

WARNING: To Reduce The Risk f Fire, Electric Shock, or Personal Injury, Mount To utlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The utlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Re-

move Knockouts In The utlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to

the building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign

object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufac-

turer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigera-

tion and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlo ans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, S witch power off

at Service panel and lock service disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent w arn-

ing device, such as a tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. T o reduce

the risk of fire, electric shock, or personal injury ,

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)

Use metal outlet box suitable for fan support (must

support 35 lbs). Before attaching fan to outlet bo x,

ensure the outlet box is securley fastened by at

least two points to a structur al ceiling member ( a

loose box will cause the fan to w abble). Use only

the screws provided with the outlet box.

Loosen set screws with locking nuts.

Remove keeper from pin and then

pin from yoke for downrod.

Thread wires and safety cable

through downrod with canopy and

yoke cover assembled.

Check the motor for plastic shipping

stabilizer tabs and remove them if

they are present.

Insert downrod into motor yoke.

Next, insert clevis pin through y oke

and downrod and secure with cotter

pin. (see inset)

Tighten both yoke set screws to fur-

ther secure downrod.

Hang assembled fan from the mounting br acket

installed to ceiling in previous steps. Mak e

sure the fan is hanging str aight. Rotate fan

until the tab on the Mounting br acket engages

the slot on the Downrod Ball. This must be

done to prevent the fan body from rotating

when the blades are in motion.

Connect black and blue wire from fan to

Black or (Hot) wire from house. Connect

White wire from Fan to White (Neutral)

wire from house. Connect Ground leads

from mounting bracket and downrod to

Ground lead from house. Refer to

Safety Tips section of manual.

House Fan

Blue

Black

White

Green

Black

White

Ground

Make wire connections to power source using wire

nuts provided. Make sure that no filiments are out -

side of the wirenut. After making the wire connec -

tions, the wires should be spread apart with the

grounded conductor and the equipment-grounding

conductor on one side of the outlet bo x and

ungrounded conductor on the other side of the outlet

box.

Attach blade arms to blades using

the blade arm screws and w ashers

provided.

Loosen the 3 screws to enable the

movement of the motor housing.

After desired position is met, tighten

the 3 screws previously loosened

securely.

Motor Housing adjustment to

room.

Loosen one and remove one preassem-

bled screw from mounting bracket. Save

screw. Lift canopy up, aligning its keyhole

slot with the preassembled screw on

mounting bracket and twist clockwise to

lock in place. Re-install the removed

screw and tighten all screws securely.



For Canadian installation and for USA fan and light

kit combinations over 35 lbs, in both flush and

downrod modes the safety cable must be installed

into the house structure beams using 3” lag

screws, washers and lock washers provided. Make

sure that when the safety cable is fully extended

the lead wires are longer than the cable and no

stress is placed on the lead wires.

48+:If Installing The Secondary Support Safety

Cable in the U.S., Do Not Remove Knockouts In

The Outlet Box.

 Safety cable installation

!',+8='(1+

'-!)6+;

safety

cable

3” lag

screw

lock

washer

Turn the motor housing by holding

onto the bottom shaft of the fan and

turning with your other hand to your

desired position. See page 7 for

example.

Place the switch cap over the light kit

until the threaded rod is completely

through.

Remove the plastic insert from

the center of the switch cap .

Attach switch cap to fan b y lining up

4 screw holes and installing the 4

screws removed and saved from ear-

lier step. Tighten screws securely.

Connect 9 plug connectors together.

Match the color strips on the plugs.

For install

without Light

kit continue

with step 23.

For install with

Light kit go to

step 25.

Remove 4 screws from the switch

cap plate and save for later use.

Install switch housing to light kit b y

aligning keyslots and turning clock-

wise. Tighten 3 screws.

Remove 1 screwand save. Loosen

other 2 screws .Remove cap by

twisting and pulling down. Save

screws.

The screws, washers, and motor

pads are pre-installed to the blade

holders. Attach blade assembly to

motor and tighten screws securely.

Connect plug from fan to switch

housing plug. Match the color strips

on the plugs.

Install the keeper nut onto the

threaded pipe of the light kit.

Connect the white wire from the

switch cap to the white wire from the

light kit. Connect the bl ue wire from

the switch cap to the bl ack wire from

the light kit.

Remove the Finial nut b y

unscrewing. Save for later use.

Remove the Hex nut b y

unscrewing. Save for later use.

Attach switch cap to fan b y lining up

4 screw holes and installing the 4

screws removed and saved from ear-

lier step. Tighten screws securely.

Install 3 x 40 watt incandescent candelabra

bulbs. Bulbs included.

WARNING: Over lamping the fan will

result in the fan lights shutting down

until the proper wattage of bulbs are

installed.Reset the lights by turning off

the wall switch, breaker,or by remote.

Replace bulbs with the correct wattage

bulbs, turn the power on.

Install glass onto light kit, install

rubber washer and hex nut to hold in

place and tighten in direction of

arrow.

Adjust the light kit to align with the

upper motor housing. See bottom

picture for alignment of your fan to

the shape of your room. You may

position your fan to your style.

Align the hole in glass with hole in

final cap to allow the fan speed con-

trol pull chain to pass through.

Install finial and tighten in direction

of arrow.

1.Check main and branch circuit fuses or circuit break ers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3.Make sure forward/reverse switch is firmly in up or down position. F an will not operate when switch is

in the middle.

4.Make sure that shipping stabilizer tabs have been removed from motor.

1.Check to make sure all screws in motor housing are snug (not o ver tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not r attling against each other or

against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.If using an optional Ceiling F an Light Kit, check to be sure the screws securing the glassw are are fin-

ger tight. Check to be sure light bulb is tight in sock et and not touching glass shade(s). If vibr ation

persists from glass, remove glass and install a 1/4" wide rubber band on glass neck to act as an insula -

tor. Replace glass and tighten screws against rubber band.

5.Some fan motors are sensitive to signals from Solid State v ariable speed controls. DO NOT USE a

Solid State variable speed control.

6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this

period.

1.Make sure that the ridge of the canop y engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor .

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction bo x and junc-

tion box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade lev els are unequal. Check this lev el by selecting a

point on the ceiling abo ve the tip of one of the blades. Measure this distance from blade tip to ceilng.

Keeping measure within 1/8", rotate the fan until the next blade is positioned for measurement. R epeat

for each blade. If all blade lev els are not equal, y ou can adjust blade lev els by the following procedure.

To adjust a blade tip down, insert a w asher (not supplied) between the blade and blade holder at the

screw closest to the motor. To adjust a blade tip up , insert washer (not supplied) between the blade and

blade holder at the two screws farthest from the motor . Reverse the position of the w asher if blades

mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side b y side) blades can redistribute the

weight and possibly result in smoother oper ation.

1.Check blue wire from fan to mak e sure it is connected to hot wire from house

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

WARNING: Over lamping the fan will result in the fan lights shutting down until the

proper wattage of bulbs are installed.

Reset the lights by turning off the wall switch, breaker,or by remote. Replace bulbs with the

correct wattage bulbs, turn the power on.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds

noisy:

1. If fan does not

start:

3. If fan wobbles:

4. If light does not

work:

TROUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it ma y be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors ma y be mistaken for defects. If you experience any faults, please check this Trouble

Shooting Chart. If a problem cannot be remedied, or y ou are experiencing difficulty in installation, please call our

Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Trou le Suggested Remedy

Andere Handbücher für AC-552

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5CO52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SBR56 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MZR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company MCDF series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR60XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR99XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5OR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIW52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DAXX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVOR56 D-V1 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS52 D-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LCM52XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ALMSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-572LF2000 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VTR52D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MAR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4AIR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WA52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVDC52D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR70 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BCTR20 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52ES D Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung