Monte Carlo Fan Company 5CY60XX Series Bedienungsanleitung

Quality Ceiling fans

For 5CY60XX Series Fans

Owner’s

Manual

Ceiling Fan Installation Instructions

Total fan weight

READ AND SAVE THESE INSTRUCTIONS

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Remove keeper from pin. Remove

pin, replace keeper and save.

Thread wire through downrod with

canopy and yoke cover assembled

onto downrod.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet box is securely

fastened by at least two points to a structural

ceiling member ( a loose box will cause the fan

to wobble). Use only the screws provided

with the outlet box.

Loosen the 2 set screws in yoke for

downrod to slip into yoke.

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-

1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equip-

ment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

Note--For Outdoor Fans Only: Suitable for use in wet locations when installed in a GFCI protected branch circuit.

10.

11.

12.

13.

14.

15.

16.

Installation

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

SAFETY TIPS

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Insert downrod into motor yoke.

Next, insert clevis pin through yoke

and downrod.

Carefully lift fan assembly onto mounting

bracket. Rotate fan so that the notch on the

ball engages the ridge in the mounting bracket.

This will allow hands-free wiring.

Install 3 screws and washers per

blade and tighten securely. Repeat

for all 5 blades. The blades will have

a label showing this side up on each

blade.

Make wire connections to power source

using wire nuts provided. Make sure that

no filiments are outside of the wirenut.

After making the wire connections, the

wires should be spread apart with the

grounded conductor and the equipment-

grounding conductor on one side of the out-

let box and ungrounded conductor on the

other side of the outlet box.

For pullchain controls, follow diagram above.

Make sure that all exposed wiring is secured

inside wire nuts. Note: Wires from house may

vary in color and may not include ground wire.

After wiring is conplete, gently push wires into

junction box with wire nuts pointing upward.

Refer to point 3 of safety tips.

15 House Fan

Black

White

Green

Black

White

Green(downrod)

Green(Bracket)

Blue

For control of fan and optional light from wall

location, follow diagram above. NOTE: A profes-

sional electrician is recommended for this type

of installation.

Raise the canopy up and align the

two holes in the canopy with the two

holes in the hanger bracket. Secure

with two screws provided.

Tighten both yoke set screws to fur-

ther secure downrod.

Light Switch

Fan Switch

Wall

Control

Secure with cotter pin.

Remove screws from stabilizer plate

on bottom of fan motor.

10 11

Remove stabilizer plate you will not

need this plate.

For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be

installed into the house structure beams using

the 3” lag screws,washers, and lock washers.

provided. Make sure that when the safety cable

is fully extended the leadwires are longer than

the cable and no stress is placed on the lead-

wires.

13 Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw lock

washer

Install the switch housing using the 4

screws previously removed.

Remove 4 screws and save to install

switch housing.

Install switch housing plate by twist-

ing plate with key hole slots into

place. Replace screw removed and

tighten the 3 screws securely.

Connect plug from fan to switch

house plug.

Loosen 2 screws with key slots and

remove 1 screw without slot from

motor plate and save screw.

The screws, washers, and motor

pads are pre-installed to the blade

holders. Attach blade assembly to

motor and tighten screws securely.

Customer Service Center

740 S.W. Loop 820, Suite 110

Fort Worth, Texas 76115

1-800-519-4092

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Make sure that any shipping stabilizer has been removed from motor.

CAUTION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls. DO

NOT USE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is

positioned for measurement. Repeat for each blade. If all blade levels are not equal, you can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer

(not supplied) between the blade and blade holder at the screw closest to the motor. To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at

the two screws farthest from the motor. Reverse the position of the washer if blades mount

from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

1. If fan does not

start:

3. If fan wobbles:

4. If light does not

work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis-

connecting means to prevent power from being switched on accidentally. When the service dis-

connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Trouble Suggested Remedy

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company MC5B241 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VNR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VLR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Arcade 3ARR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DOR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LNR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PAR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5vsr44XXd-l series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3FSR52 series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PE56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR52EP Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ALR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WCR56XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company MC263 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5KBR54 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR60XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VTR52/38 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CNHSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HDR52D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GFR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4BFR54 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ED56WAD Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung