Monte Carlo Fan Company Mach One Series Bedienungsanleitung

Page 1 – MACH ONE-UL-

English; 10/20/97

OWNER’S

MANUAL

QUALITY CEILING FANS

Ceiling Fan Installation Instructions

For Mach One Series

Total fan weight with

light kit included.

Authorized Monte Carlo Dealer www.NovaLightingStore.com 800-860-1207

Monte Carlo Fans & Fixtures Available at www.NovaLightingStore.com 800-860-1207

Page 2 – MACH ONE-UL-

English; 10/20/97

INSTALLATION

TOOLS REQUIRED

Phillips Screwdriver Wire Cu ers Pliers S ep Ladder

1Unpack and inspect fan carefull

to be certain all contents are

included.

Turn off power at breaker box to

avoid possible electrical shock.

Safety Tips

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

READ AND SAVE THESE INSTRUCTIONS

Use metal outlet box suitable for

fan support. Secure outlet box

directl to the building structure

using ceiling joist screws (included).

Outlet box must support 35 lbs.

Place fan bod with light fitter

pointing upward. Attach the 3

blades as shown in diagram above.

Carefull turn fan motor over so

that the upper housing is facing up.

Remove the 3 screws hold the

upper housing in place. Lift upper

housing to reveal the motor. Save

screws for step 6.

Ring blade holder Screws from step 5

Attach ring blade holder to blades with

the 6 screws provided as shown in fig. A

above. Make sure all screws holding

blades are tight before proceding to

the next step. Re-attach upper

housing to main bod using reverse

of step 6 as shown in fig. B above.

Installation work and electrical wiring must be done b qualified person(s) in accordance with all applicable codes and standards(ANSI/

NFPA 70-1996), including fire-rated construction.

Use this unit onl in the manner intended b the manufacurer. If ou have an questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before ou begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentall . When the service disconnecting means cannot be locked, securel fasten a prominent warning device, such as a

tag, to the service panel.

Be cautious! read all instructions and safet information before installing our new fan. Review the accompan ing assembl diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site ou choose allows the fan blades to rotate without an obstructions. Allow a minimum clearance of 7 feet

(2.1 Meters) from the floor to the trailing edge of the blade.

WARNING: MOUNT ONLY TO AN OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT.To reduce the risk of fire, electric shock, or

personal injur , mount to outlet box or supporting s stem acceptable for fan support.(Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

Attach the mounting bracket using onl the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with an solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment ma be affected b this unit’s operation. Follow the heating

equipment manufacturer’s guideline safet standards such as those published b the National Fire Protection Association (NEPA), and the

American Societ for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentall . When the service disconnecting means cannot be locked, securel fasten a prominent warning device, such as a

tag, to the service panel.

10.

11.

12.

13.

14.

15.

Authorized Monte Carlo Dealer www.NovaLightingStore.com 800-860-1207

Monte Carlo Fans & Fixtures Available at www.NovaLightingStore.com 800-860-1207

Page 3 – MACH ONE-UL-

English; 10/20/97

INSTALLATION

Remove canop and downrod from

pol foam. Slide canop over downrod as

pictured. Feed lead wires through downrod

and install downrod into fan oke. Install

cross pin with locking washer through

oke and downrod making sure to

tighten securel . Install set screw into

oke and tighten securel .

Downrod

Canop

Crosspin

Yoke

8While the fan assembl is still on

the ground thread the safet cable

through the mounting bracket.

safet

cable

mounting

bracket

Set

screw

plain

washer

lag

screw

safet

cable

Lift fan assembl and install the safet cable

directl to the building structure using the

3" lag screw and plain washer provided.

Before proceeding to the next step make

sure that the cable is properl installed and

will support the fan weight. Make

sure the screw washer and safet

cable are installed using the order

pictured above.

Ridge

Ball

Notch

A. Carefull lift fan assembl onto

mounting bracket. Rotate fan so that

the notch on the ball engages the

ridge in the mounting bracket. This

will allow hands-free wiring.

Install mounting bracket to outlet box

in ceiling using the screws provided

with the outlet box and washers.

Authorized Monte Carlo Dealer www.NovaLightingStore.com 800-860-1207

Monte Carlo Fans & Fixtures Available at www.NovaLightingStore.com 800-860-1207

Page 4 – MACH ONE-UL-

English; 10/20/97

Remote Receiver

Antenna

Wire Nuts

FIG.A FIG.B

WIRING DIAGRAM

REMOTE RECEIVER

RED TO FAN

MOTOR

BLUE TO LIGHT

BLACK TO HOUSE

WHITE TO FAN

WHITE TO HOIUSE

WHITE (COMMON)

PLAIN (GROUND)

BLACK (HOT) WHITE (COMMON)

BLUE (HOT) LIGHT

BLACK (HOT) FAN

GREEN (GROUND)

Make connections as shown above. Make

sure all exposed conductors are in

the wire nuts. After all connections

are made push wire nuts into

junction box with wire nuts pointing

upward.

HOUSE FAN

Remote Receiver

DIP Switch

Remote

Transmitter

Before installing the remote receiver. Make sure

the DIP switches in the Transmitter and receiver

are set the same. Use instrument with a sharp

point to move the switches into the proper

positions. The Remote will not operate if this

procedure is not done. If interference from

outside transmitters or other remote devices

is incountered, change the dip switch

settings on both transmitter and receiver.

Carefull insert remote receiver into the

Mounting Bracket. Make sure the Antenna is not

pinched b running it through the Mounting

Bracket first (FIG.A). Receiver should be located

as pictured above(FIG.B). Make wiring

connections as per step 12. Make sure

that all wire nut connections are tight with

no exposed conductors. Point connectors

upward and push into the junction box.

Raise the canop up and align the two

holes in the canop with the two holes

in the hanger bracket. Secure with

two 5/32 x 1/2" screws provided. 16

Install 75W MAX JD t pe Halogen

lamp into lampholder. Install glass

b turning clocksise until locked in

position.

REMOTE OPERATION

Install 9v batter b removing batter cover on back of

transmitter and connecting to terminals and re-install cover.

FAN SPEED Depress "1" for low speed, "2" for medium or "3"

for high. To turn fan off press "0"

LIGHT DIMMER To turn light on, press the button with bulb

icon once quickl . To turn off press once quickl while the

light is on. To dim light hold down button with bulb icon.

The light will c cle from bright to dim to bright until

button is released. Light will maintain last setting if

turned off. Note: If power is interrupted to fan light

will come on at brightest setting.

Light

control

button

Fan

speed

controls

Batter

compart-

ment

12 13

Authorized Monte Carlo Dealer www.NovaLightingStore.com 800-860-1207

Monte Carlo Fans & Fixtures Available at www.NovaLightingStore.com 800-860-1207

Page 5 – MACH ONE-UL-

English; 10/20/97

TROUBLE SUGGESTED REMEDY

If ou have difficult operating our new ceiling fan, it ma be the result of incorrect assembl , installation,

or wiring. In some cases, these installation errors ma be mistaken for defects. If ou experience an faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or ou are experiencing difficult

in installation, please call our Customer Service Center at the number printed on our parts list insert sheet.

1. If fan does not

sta t:

TROUBLESHOOTING GUIDE

Check main and branch circuit fuses or circuit breakers.

Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

Make sure forward/reverse switch is firml in up or down position. Fan will not operate when

switch is in the middle.

Remove remove receiver in canop and connect fan directl to power. Turn on power. If fan

operates, remote reciever is defective.

Check to make sure all screws in motor housing are snug (not over tightened).

Check to make sure the screws which attach the fan blade holder to the motor are tight.

Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT

USE a Solid State variable speed control.

Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after

this period.

All blades are weighed and grouped b weight. Natural woods var in densit which could cause

the fan to wobble even though all blades are weight-matched. The following procedures should

eliminate most of the wobble. Check for wobble after each step.

Make sure that canop and mounting bracket are tightened securel to ceiling junction box and

junction box is mounted firml to ceiling joist.

If blade wobble is still noticeable, interchanging two adjacent (side b side) blades can redis-

tribute the weight and possibl result in smoother operation.

Check blue wire from fan to make sure it is connected to blue wire from Remote Receiver.

Check for loose or disconnected wires in fan switch housing.

Check for fault light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds

noisy:

3. If fan wobbles:

4. If light does not

wo k:

2900 WEST SEMINARY DR. SUITE 200

FORT WORTH TEXAS 76133

1-800-519-4092

Authorized Monte Carlo Dealer www.NovaLightingStore.com 800-860-1207

Monte Carlo Fans & Fixtures Available at www.NovaLightingStore.com 800-860-1207

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company Bravo 5BO52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ALMSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GFR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ATR44XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MO52 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLYR52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Mach One Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CE52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Cupra 3CPR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TTHR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TV52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VL52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR99XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DVR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DIR58 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5vsr44XXd-l series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TSR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AXR52XX3-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Jovie 3JOVR52 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung