Monte Carlo Fan Company 8TNR56 D Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Total fan weight with light kit

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

8TNR56XXD Series Fan

ETL Model NO. : 8TNR56XXD

11 kgs

24.2 lbs

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the

building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. RH-786R manufactured

by Rhine Electronic Co., Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable

speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble). Remove the two outlet

box screws provided with the box,

aligning the holes of the mounting

bracket with the holes of the outlet box.

Reinstall the 2 outlet box screws

securely.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Remove preassembled cross pin and

keeper pin from downrod.

Place downrod over canopy. Thread lead

wires and safety cable from motor

assembly through downrod.

Slip downrod into motor housing yoke,

aligning holes and install cross pin and

keeper pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the

cross pin, and then evenly tighten the

downrod set screws on motor housing

yoke.

Warning: Cross pin and keeper pin must

be installed securely, failure to install them

will result in serious injury.

Mounting bracket

Downrod

Canopy

Downrod

Cross pin

Keeper pin

Cross pin

Keeper pin

7 8 9

10 11 12

Partially loosen set screws for the spring

clips

Place upper glass on top of fan. Adjust the

spring clips to hold the glass in place.

Tighten all set screws securely.

Install 4 x 25 watt candelabra base bulbs

(25W Max), Bulbs included

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod mode the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Make wiring connections using wire

connectors provided as indicated above.

Connect Black wire from fan to Black

(Hot) wire from house. Connect White

wire from Fan to White (Neutral) wire from

house. Connect all green grounded wires

to Grounded wire from House. Make sure

that no ﬁlaments are outside of the wire

connectors.

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

120V 25W Bulb

Spring clip

Power supply

Black

white

Grounding/Green

Black

Wall switch

Tab

Slot

Upper

glass

13 14 15

16 17 18

Partially loosen 2 of the set screws on

mounting bracket corresponding to the

slotted holes on the canopy upper ring.

Remove the other 2 set screws. Save

screws.

Raise canopy to mounting bracket,

aligning loosened screws in mounting

bracket with slotted holes in canopy.

Twist canopy to lock. Reinstall screws

that were previously removed and then

tighten all screw securely.

Flip the blade assembly over and install

blade supporting ring onto the blades

with screws provided.

Note: Make sure the side with a label

“This side up” is installed upward.

Lift blade assembly up. Aligning the holes

on the coupler and the screw holes on

motor and then install it onto motor using

the screws provided. Tighten screws

securely.

Note: Be sure to use the set screws in

the pack marked Step 16.

Loosen 2 and remove 1 preassembled

screw from the plate on motor. Save

screw for later use.

Attach light pan onto the plate on motor,

aligning the keyhole slots on the light

plate with the preassembled screws on

the plate. Twist clockwise till lock.

Reinstall the screws which were just

removed. Tighten all screws securely.

Loosen 2 and remove 1 preassembled

screw from the light pan. Save screw for

later use.

Install blades on ﬂywheel with set screws

provided.

Note: Be sure to use the set screws in

the pack marked Step 14.

Note: Make sure the side with a label

“This side for blade installation” is

installed upward.

Note: Put blades on carpet to avoid

blade damage from scratch

Flywheel Blade

This side for

blade installation

This side up

Blade supporting ring

19 20 21

Connect white wire from fan to white wire

from light ﬁxture, and then connect blue

wire from fan to black wire from light

ﬁxture.

Attach light ﬁxture onto light pan.

Reinstall the 3 set screws removed in

step 18 and tighten all screws securely.

Install 2 G9 35W bulb. Bulb included.

Warning: Over lamping the fan will result

in the fan lights shutting down until the

proper wattage of bulbs are installed.

Reset the lights by turning off, replace

bulbs with the correct wattage bulbs, turn

the power on.

Caution: Do not replace bulb until it

cools down.

Attach glass to light pan by locating

dimples in light pan with grooves on the

glass and twist clockwise until tight.

Bulb

Blue

White

Light ﬁxture

Black

Remote Controller Operation

Remove the battery cover from the remote control transmitter and install

battery. Replace the cover. This remote uses 12V battery, Duracell MN21 /

Evereday A23 / GP 23A all 12V.

Note: If not using for long periods of time, remove battery to prevent

damage to remote transmitter, and store the remote transmitter away from

excess heat or humidity

Set/change the dip switch position on the transmitter to desired code

setting. If you have more than one fan in your house and you don't want them

to be controlled by the same transmitter, you will need to change the position

of the dip switches.

Remote Control Setting (Learn function) and Speed Setting

1.Restore power to your fan, press and hold the “SET” button for at least 5

seconds. You must press the ‘SET” button with in 60 seconds of restoring

power to the fan.

Note

: If the fan is installed with light (down light), light will twinkle twice then

off. The remote control setting process is complete and your fan is ready for

use. For fans without light, check operation using remote transmitter.

Note

: If the power is on already, you must turn the power off, and then turn

the power back for remote control setting.

The fan will start to run and begin the control setting process. The fan will

run in both directions for a total of approximately 5 minute, then the fan will

stop. The control and speed setting process is complete and the fan is ready

for use.

12V BATTERY

The buttons on the remote control transmitter control the fan speed and light as follows.

Fan speed

Ⅰ= minimum speed Ⅱ= low speed

Ⅲ= medium low speed Ⅳ= medium speed

Ⅴ= medium high speed Ⅵ= high speed

■ This button turns the fan off.

Forward/Reverse button- This button is to control direction of fan rotation. Press once

to change direction of the fan rotation. Fan must be running to reverse.

Light button- Press this button quickly to turn light on or off. To dim light, hold down the

button, the light will cycle from bright to dim to bright until button is released.

Note

: This remote controller has auto resume function, the fan and light will maintain the

last setting if turned off.

Dip switch

“Set”

Battery cover

Forward/

Reverse

Forward/Reverse

The receiver provides the following protective functions

Lock protection- The DC motor has a build-in safety feature

against blade obstruction during operation. If something

obstructs the fan blades the motor will stop operation after

30 seconds of interruption. Please remove obstacles and

reset.

Over 80W protection- When the receiver detects motor

power consumption which is greater than 80W, the receiver

power will shut down and fan operation will cease.

Disconnect the power supply and return power on to the fan

after 5 seconds.

Tips for end users

1. If your fan is operated automatically after installation and power on, it is because your fan is still memorize the previous

setting at factory. Make Remote control setting (learn function) and your fan will be ready for use.

2. If fan or light isn’t working, reset power (turn the power off for at least 5 seconds and then turn the power back) and redo the

remote setting.

3. It is not available to separately operate the remote setting for more than one fan in the same room (in the area where remote

signal can reach to) if they share the same power supply. Separate power supplies (like as using individual wall switches for each

fan) is required if you want to separately control more than one fan in same room.

Install Transmitter wall mount cradle with 2 screws provided.

Move the trim plate out from wall mount cradle and install

the wall mount cradle with 2 screws provided. Replace the

trim plate.

Trim plate

Wall mount cradle

Trouble Shooting

,I\RXKDYHGLI¿FXOW\RSHUDWLQJ\RXUQHZFHLOLQJIDQLWPD\EHWKHUHVXOWRILQFRUUHFWDVVHPEO\LQVWDOODWLRQ

RUZLULQJ,QVRPHFDVHVWKHVHLQVWDOODWLRQHUURUVPD\EHPLVWDNHQIRUGHIHFWV,I\RXH[SHULHQFHDQ\IDXOWV

SOHDVHFKHFNWKLV7URXEOH6KRRWLQJ&KDUW,IDSUREOHPFDQQRWEHUHPHGLHGRU\RXDUHH[SHULHQFLQJGLI¿FXOW\LQ

LQVWDOODWLRQSOHDVHFDOORXU&XVWRPHU6HUYLFH&HQWHUDWWKH

QXPEHUSULQWHGRQ\RXUSDUWVOLVWLQVHUWVKHHW

Warning%HIRUH VHUYLFLQJRU FOHDQLQJXQLW 6ZLWFKSRZHU RIIDW 6HUYLFHSDQHO DQGORFN VHUYLFHGLVFRQQHFWLQJ

PHDQVWRSUHYHQWSRZHUIURPEHLQJVZLWFKHGRQDFFLGHQWDOO\:KHQWKHVHUYLFHGLVFRQQHFWLQJPHDQVFDQQRWEH

ORFNHGVHFXUHO\IDVWHQDSURPLQHQWZDUQLQJGHYLFHVXFKDVDWDJWRWKHVHUYLFHSDQHO

&KHFNPDLQDQGEUDQFKFLUFXLWIXVHVRUFLUFXLWEUHDNHUV

&KHFNOLQHZLUHFRQQHFWLRQVWRIDQDQGVZLWFKZLUHFRQQHFWLRQVLQVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRII

,IWKLVIDQXVHVPDQXDOIRUZDUGUHYHUVHVZLWFKPDNHVXUHWKHVZLWFKLVSXVKHG¿UPO\HLWKHU

ZD\)DQZLOOQRWRSHUDWHZKHQVZLWFKLVLQWKHPLGGOH

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNHVXUH

EDWWHU\LVHIIHFWLYH

&KHFNWRPDNHVXUHDOOVFUHZVLQPRWRUKRXVLQJDUHVQXJQRWRYHUWLJKWHQHG

&KHFNWRPDNHVXUHWKHVFUHZVZKLFKDWWDFKWKHIDQEODGHKROGHUWRWKHPRWRUDUHWLJKW

&KHFNWRPDNHVXUHZLUHQXWFRQQHFWRUVLQVZLWFKKRXVLQJDUHQRWUDWWOLQJDJDLQVWHDFKRWKHU

RUDJDLQVWWKHLQWHULRUZDOORIWKHVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRIIEHIRUHHQWHULQJVZLWFKKRXVLQJ

&KHFNWREHVXUHOLJKWEXOELVWLJKWLQVRFNHWDQGQRWWRXFKLQJWKHJODVVVKDGH

6RPHIDQPRWRUVDUHVHQVLWLYHWRVLJQDOVIURP6ROLG6WDWHYDULDEOHVSHHGFRQWUROV

$OORZEUHDNLQ SHULRGRI KRXUV0RVW QRLVHVDVVRFLDWHG ZLWK DQHZ IDQZLOOGLVDSSHDU

DIWHUWKLVSHULRG

,IWKLVLVDGRZQURGPRXQWIDQPDNHVXUHWKHULGJHRQPRXQWLQJEUDFNHWHQJDJHVWKHQRWFKLQ

WKHGRZQURGEDOO

0DNHVXUHWKDWFDQRS\PRXQWLQJEUDFNHWRUPRXQWLQJSODWHDUHWLJKWHQHGVHFXUHO\WRFHLOLQJ

MXQFWLRQER[DQGMXQFWLRQER[LVPRXQWHG¿UPO\WRFHLOLQJMRLVW

&KHFNWKDWDOOEODGHVDUHVFUHZHG¿UPO\LQWREODGHKROGHUV

&KHFNWKDWDOOEODGHKROGHUVDUHWLJKWHQHGVHFXUHO\WRPRWRU

0RVWIDQ ZREEOHSUREOHPV DUHFDXVHG ZKHQEODGHOHYHOV DUHXQHTXDO&KHFN WKLVOHYHO E\

VHOHFWLQJDSRLQWRQWKH FHLOLQJDERYHWKHWLS RI RQHRI WKHEODGHV 0HDVXUH WKLVGLVWDQFH IURP

EODGHWLSWRFHLOQJ.HHSLQJPHDVXUHZLWKLQURWDWHWKHIDQXQWLOWKHQH[WEODGHLVSRVLWLRQHG

IRUPHDVXUHPHQW5HSHDWIRUHDFKEODGH,IDOOEODGHOHYHOVDUHQRWHTXDO\RXFDQDGMXVWEODGH

OHYHOVE\ WKHIROORZLQJSURFHGXUH 7RDGMXVW D EODGHWLS GRZQLQVHUWD ZDVKHUQRWVXSSOLHG

EHWZHHQWKHEODGHDQGEODGHKROGHUDWWKHVFUHZFORVHVWWRWKHPRWRU7RDGMXVWDEODGHWLSXS

LQVHUWZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGHKROGHUDWWKHWZRVFUHZVIDUWKHVWIURP

WKHPRWRU5HYHUVHWKHSRVLWLRQRIWKHZDVKHULIEODGHVPRXQWIURPWRSRIEODGH

,IEODGH ZREEOHLVVWLOO QRWLFHDEOHLQWHUFKDQJLQJ WZR DGMDFHQWVLGH E\ VLGHEODGHVFDQ

UHGLVWULEXWHWKHZHLJKWDQGSRVVLEO\UHVXOWLQVPRRWKHURSHUDWLRQ

&KHFNEOXHZLUHIURPIDQWRPDNHVXUHLWLVFRQQHFWHGWRKRWZLUHIURPKRXVH

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQIDQVZLWFKKRXVLQJ

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQOLJKWNLW

&KHFNIRUIDXOW\OLJKWEXOEDQGPDNHVXUHEXOELVWLJKWLQVRFNHW

5HPRYHOLJKWNLWDQGFKHFNWKHSOXJFRQQHFWLRQVLIWKH\DUHSUHVHQW

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNHVXUH

EDWWHU\LVHIIHFWLYH

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRIIEHIRUHHQWHULQJVZLWFKKRXVLQJDQGRUFDQRS\

WARNING2YHUODPSLQJWKHIDQZLOOUHVXOWLQWKHIDQOLJKWVVKXWWLQJGRZQXQWLOWKHSURSHU

ZDWWDJHRIEXOEVDUHLQVWDOOHG5HVHWWKHOLJKWVE\WXUQLQJRIIUHSODFHEXOEVZLWKWKHFRUUHFW

ZDWWDJHEXOEV7XUQSRZHURQ

,IIDQVRXQGVQRLV\

,IIDQZREEOHV

,IOLJKWGRHVQRWZRUN

,IIDQGRHVQRWVWDUW

Trouble Suggested Remedy

Nov.2013

Nov.2014 add a note on steps 14 and 14

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5AB52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MTR38TMO-L Handbuch

Monte Carlo Fan Company

Monte Carlo Fan Company 5TQ52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ROZR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Radial 5RA52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3LRR66 Service-Handbuch

Monte Carlo Fan Company

Monte Carlo Fan Company 5AGR56XXD series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Lowden 5LWDR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CU52WH Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Haven 5HVO52BKD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR60XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SBR56XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SLR52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TF24 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3LR38 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR99 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CXR52 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LLR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ROR Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3LD48 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung