Motorline professional Portugal MR65 Gebrauchs- und Pflegehandbuch

V2.1

REV. 07/2021

MR65MR65 EN

USER’S AND INSTALLER’S MANUAL

A B

10B

11A

ENEN

TECHNICAL CHARACTERISTICS

MR

INSTRUCTIONS FOR FINAL CONSUMERS/SPECIALIZED TECHNICIANS

ADJUSTMENT OF THE DETECTION AREA DEPTH: INFRARED

CONFIGURATION BY REMOTE CONTROL

. SAFETY INSTRUCTIONS

. THE PRODUCT

. PROGRAMMING

. INSTALLATION

. CONFIGURATION

. TROUBLESHOOTING

DESCRIPTION

DIMENSIONS

LED INDICATIONS

INSTALLATION AND CONNECTIONS

ADJUSTMENT OF THE DETECTION AREA DEPTH: RADAR

MAINTENANCE MODE

ADJUSTMENT OF THE DETECTION AREA WIDTH: INFRARED

CHECKING THE SETTINGS

ADJUSTMENT OF THE DETECTION AREA WIDTH: RADAR

SET AND CLEAR FOURDIGIT SECURITY CODE

LED INDICATORS COMMAND LED

00. CONTENT

INDEX

01. SAFETY INSTRUCTIONS

This product is certified in accordance with European

Community (EC) safety standards.

This product complies with Directive 2011/65/EU of the

European Parliament and of the Council, of 8 June 2011, on

the restriction of the use of certain hazardous substances

in electrical and electronic equipment and with Delegated

Directive (EU) 2015/863 from Commission.

(Applicable in countries with recycling systems).

This marking on the product or literature indicates that the

product and electronic accessories (eg. Charger, USB cable,

electronic material, controls, etc.) should not be disposed

of as other household waste at the end of its useful life. To

avoid possible harm to the environment or human health

resulting from the uncontrolled disposal of waste, separate

these items from other types of waste and recycle them

responsibly to promote the sustainable reuse of material

resources. Home users should contact the dealer where

they purchased this product or the National Environment

Agency for details on where and how they can take these

items for environmentally safe recycling. Business users

should contact their vendor and check the terms and

conditions of the purchase agreement. This product and

its electronic accessories should not be mixed with other

commercial waste.

This marking indicates that the product and electronic

accessories (eg. charger, USB cable, electronic material,

controls, etc.) are susceptible to electric shock by direct or

indirect contact with electricity. Be cautious when handling

theproductandobserveallsafetyproceduresinthismanual.

ATTENTION:

A B

ENEN

GENERAL WARNINGS

•This manual contains very important safety and usage information.

very important. Read all instructions carefully before beginning the

installation/usage procedures and keep this manual in a safe place

that it can be consulted whenever necessary.

•This product is intended for use only as described in this manual. Any

other enforcement or operation that is not mentioned is expressly

prohibited, as it may damage the product and put people at risk

causing serious injuries.

•Thismanual isintended firstlyforspecialized technicians, anddoesnot

invalidate the user’s responsibility to read the “User Norms” section in

order to ensure the correct functioning of the product.

•The installation and repair of this product may be done by qualified

and specialized technicians, to assure every procedure are carried

out in accordance with applicable rules and norms. Nonprofessional

and inexperienced users are expressly prohibited of taking any action,

unless explicitly requested by specialized technicians to do so.

•Installations must be frequently inspected for unbalance and the

wear signals of the cables, springs, hinges, wheels, supports and other

mechanical assembly parts.

•Do not use the product if it is necessary repair or adjustment is

required.

•When performing maintenance, cleaning and replacement of parts,

the product must be disconnected from power supply. Also including

any operation that requires opening the product cover.

•The use, cleaning and maintenance of this product may be carried

out by any persons aged eight years old and over and persons whose

physical,sensorialormentalcapacitiesarelower,orbypersonswithout

any knowledge of the product, provided that these are supervision

and instructions given by persons with experienced in terms of usage

of the product in a safe manner and who understands the risks and

dangers involved.

•Children shouldn’t play with the product or opening devices to avoid

01. SAFETY INSTRUCTIONS

the motorized door or gate from being triggered involuntarily.

WARNINGS FOR TECHNICIANS

•Before beginning the installation procedures, make sure that you have

all the devices and materials necessary to complete the installation

of the product.

•You should note your Protection Index (IP) and operating temperature

to ensure that is suitable for the installation site.

•Provide the manual of the product to the user and let them know how

to handle it in an emergency.

•If the automatism is installed on a gate with a pedestrian door, a door

locking mechanism must be installed while the gate is in motion.

•Do not install the product “upside down” or supported by elements do

not support its weight. If necessary, add brackets at strategic points

to ensure the safety of the automatism.

•Do not install the product in explosive site.

•Safety devices must protect the possible crushing, cutting, transport

and danger areas of the motorized door or gate.

•Verify that the elements to be automated (gates, door, windows,

blinds, etc.) are in perfect function, aligned and level. Also verify if the

necessary mechanical stops are in the appropriate places.

•The central must be installed on a safeplace ofanyfluid (rain,moisture,

etc.), dust and pests.

•You must route the various electrical cables through protective tubes,

to protect them against mechanical exertions, essentially on the

power supply cable. Please note that all the cables must enter the

central from the bottom.

•If the automatism is to be installed at a height of more than 2,5m from

the ground or other level of access, the minimum safety and health

requirements for the use of work equipment workers at the work of

Directive 2009/104/CE of European Parliament and of the Council of 16

September 2009.

•Attach the permanent label for the manual release as close as possible

A B

ENEN

to the release mechanism.

•Disconnect means, such as a switch or circuit breaker on the electrical

panel, must be provided on the product’s fixed power supply leads in

accordance with the installation rules.

•If the product to be installed requires power supply of 230Vac or

110Vac, ensure that connection is to an electrical panel with ground

connection.

•The product is only powered by low voltage satefy with central (only

at 24V motors)

WARNINGS FOR USERS

•Keep this manual in a safe place to be consulted whenever necessary.

•If the product has contact with fluids without being prepared, it must

immediately disconnect from the power supply to avoid short circuits,

and consult a specialized technician.

•Ensure that technician has provided you the product manual and

informed you how to handle the product in an emergency.

•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,

turn off the power and do not use it until all safety conditions have

been met.

•In the event of tripping of circuits breakers of fuse failure, locate

the malfunction and solve it before resetting the circuit breaker or

replacing the fuse. If the malfunction is not repairable by consult this

manual, contact a technician.

•Keep the operation area of the motorized gate free while the gate in in

motion, and do not create strength to the gate movement.

•Do not perform any operation on mechanical elements or hinges if the

product is in motion.

01. SAFETY INSTRUCTIONS

SYMBOLS LEGEND:

• Important safety

notices

• Useful information

• Programming

information

• Potentiometer

information

• Connectors

information

• Buttons

information

RESPONSABILITY

•Supplier disclaims any liability if:

•Product failure or deformation result from improper installation

use or maintenance!

•Safety norms are not followed in the installation, use and

maintenance of the product.

•Instructions in this manual are not followed.

•Damaged is caused by unauthorized modifications

•In these cases, the warranty is voided.

A B

ENEN

. THE PRODUCT . THE PRODUCT

MR

• Installation height 3,5 - 6.5 meters

• Supply voltage 12 to 24Vac/dc 50/60 Hz

• Power consumption 12Vac (máx. 1,5VA) - 24Vac (máx. 3,3VA)

12Vac (máx. 150mA) 24Vac (máx. 80mA)

• Exit

Exit IR Optical relay (no polarity)

48Vdc 300mA

Radar Output Optical relay (no polarity)

48Vdc 300mA

• Operating temperature -20 a +60C

• Operating humidity < 80%

• IP IP65

• Weight 1.30kg

Reﬂection Sensor

• Detection method Active infrared reﬂector

• Response time 0,25 sec. approx.

• Presence timer 30 sec., 1, 2, 5, 10, 20 min., 1,2 hours. or 

Radar Sensor

• Detection method Moving body detection

• Transmission frequency 24,15 GHz

• Response time 0,1 sec. approx.

Note: Features are subject to change without notice.

The MR65 is a radar ideal for large doors, such as high speed doors, and can be installed up to .m high.

It has detection technology capable of differentiating people and vehicles, reducing unwanted openings,

thus saving energy.

TECHNICAL CHARACTERISTICS

LED INDICATIONS

Green On hold

Flashing Green Sensor Starting

Red Infrared sensor and/or RADAR sensor detected

Flashing Red RADAR detected

Yellow Internal detection "Line " is detecting the door moving

Flashing (fast) Green/red Sensor’s internal error

DESCRIPTION

DIMENSIONS

Sensor Wire

Remote control

receiver

Fixing support

Radar Sensor

Infrared Sensor

Conﬁrmation LED

(Blue, Yellow and Red)

Operation LED sensor

body (Red, Green)

Adjustment of radar sensor

detection area

mm

.mm

mm

°

mm

.mm

mm

User manual Cable Fixing screws ( pcs.)



03. INSTALLATION

INSTALLATION AND CONNECTIONS

To ensure the correct functioning of the MR, please note the following indications:

• Prevent the installation site from having accumulation of snow or water on the ground;

• Adjust the sensor body so that it does not detect the door;

• The Radar part of the MR can be negatively inﬂuenced by metal from the detection

ﬁeld;

• Install at a maximum height of . meters;

• Make sure no condensation forms on the sensor;

• Make sure there are no moving objects in the detection zone;

• Ensure minimal sunlight reﬂected from the ﬂoor;

• Use different frequency settings when there is more than one sensor nearby

Drill the fixing holes (. mm) according to the fixing support markings.

Remove the sensor body from the fixing support.

DETAIL A

Secure the ﬁxing support with the mounting screws provided.

Place the sensor body on the ﬁxing support. Pass the cable through the ﬁxing

support.

Make the connections according to the diagram below. (See detail A)

Red

Black

White

Green

Yellow

Blue

Gray

Brown

Power supply (no polarity)

Output  (Radar Output)

Output  (Radar Output)

Do not use

Sensor Wire

A B

6.5

6.0

5.0

4.0

3.5

3.0

2.0

1.0

1.01.02.03.04.05.0 0

6.5

6.0

5.0

4.0

3.5

3.0

2.0

1.0

1.01.02.03.04.05.06.07.08.09.0 0

[m] [m]

32°

ENEN

. PROGRAMMING

ADJUSTMENT OF THE DETECTION AREA DEPTH: INFRARED

. PROGRAMMING

ADJUSTMENT OF THE DETECTION AREA WIDTH: INFRARED

Installation height: 3500mm

Installation height: 5000mm

When the angle of the sensor

body is set to 32° When the angle of the sensor

body is set to 16°

[Distant] [Close]

32°(distante) 32°(distante)

16°(próximo) 16°(próximo)

0° 0°

When the angle of the sensor

body is set to 32°

When mounted

on the wall When ceiling

mounted

When the angle of the sensor

body is set to 16°

01 • Adjust the detection angle between 16˚ and 32˚ by moving the body angle.

A B

6.5

6.0

5.0

4.0

3.5

3.0

2.0

1.0

1.01.02.03.04.05.0 0

6.5

6.0

5.0

4.0

3.5

3.0

2.0

1.0

1.01.02.03.04.05.06.07.08.09.0 0

[m] [m]

+25° +25°

-10° -10°

32° 16°

ENEN

. PROGRAMMING

ADJUSTMENT OF THE DETECTION AREA DEPTH: RADAR

distant distantclose close

Installation height: 3500mm

25°(distant) -10°(close) 0°(IR - line 3)

Installation height: 5000mm

Sensor body angle

set to 32°

Sensor body angle

set to 32°

Sensor body angle

set to 16°

Sensor body angle

set to 16°

. PROGRAMMING

ADJUSTMENT OF THE DETECTION AREA DEPTH: RADAR

-10°

25°

The detection area varies according to object size and approach speed. The radar is

designed to detect only large objects and not people.

01 •

Adjust the detection width by turning the controller clockwise or counterclockwise.

A B

MR65 - RC

12 3

45 6

78 9

AB C

DE F

GH I

ENEN

ADJUSTMENT OF RADAR SENSITIVITY

This menu allows you to set the radar detection

sensitivity. The factory default is [5].

MINIMUM

VALUE FACTORY

VALUE MAXIMUM

VALUE

1 2 3 4 5 6 7 8 9

01 • Press function key [D] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

. CONFIGURATION . CONFIGURATION

CONFIGURATION BY REMOTE CONTROL CONFIGURATION BY REMOTE CONTROL

CONFIGURATION VALUES

FUNCTIONS

CONFIRMATION

RELAY OUTPUT

This menu allows you to set the status of the relay output (IR/Radar).

The factory value is [3].

NO/NO NO/NC NC/NO NC/NC

1 2 3 4

01 • Press function key [A] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

DIRECTION DETECTION

This menu prevents the sensor from detecting an object that moves

away from the sensor. Factory default is [1].

Nota • A deteção de direção infravermelho (IR) funciona apenas

quando todos os IR pontos de deteção estão ativos. (5x12 pontos)

BOTH APPROX.

ONLY APPROX.

JUST GO APPROX.

RADAR

ONLY

1 2 3 4

01 • Press function key [B] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

CROSS TRAFFIC

This menu prevents the sensor from detecting movement parallel to

the door. Factory default is [1].

Note • Infrared (IR) direction detection works only when all IR

detection points are active.

OFF ON IR ON RADAR

1 2 3 4

01 • Press function key [C] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

IR IR IRIR

IR IR IR

RADAR

RADAR RADAR RADARRADAR

RADAR RADAR RADAR

ATTENTION:

• If the [1-9] button is not pressed and the [#] button is pressed, the last selected [1-9]

button becomes valid.

• When the [#] button is pressed after pressing the [1-9] button, the setting is conﬁrmed

and saved.

• The last function selected on the remote control is the one that will be changed when

the [1-9] buttons are pressed.

(example: [C] followed by [2] sets Cross Trafﬁc ON)

• If you press the [#] button without pressing the [1-9] button, it will exit the setting state

without any settings being saved.

• You can switch from one function setting to another as many times as you like until the

[#] button is pressed. D



     







  

A B

ENEN

ADJUSTMENT OF INFRARED SENSITIVITY

This menu allows you to set the infrared detection

sensitivity. The factory default is [4].

MINIMUM VALUE FACTORY VALUE MAXIMUM

VALUE

1 2 3 4 5 6

01 • Press function key [E] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

INFRARED DETECTION LINES

This menu allows you to set the number of infrared

detection lines. The factory default is [5].

1 2 3 4 5

01 • Press function key [F] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

. CONFIGURATION . CONFIGURATION

CONFIGURATION BY REMOTE CONTROL CONFIGURATION BY REMOTE CONTROL

INFRARED WIDTH ADJUSTMENT - LEFT SIDE

This menu allows you to set the infrared detection width for

the left side of the sensor. The factory default is [4].

L L L L

1 2 3 4

01 • Press function key [G] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

INFRARED WIDTH ADJUSTMENT – RIGHT SIDE

This menu allows you to set the infrared detection width for

the right side of the sensor. The factory value [4].

R R R R

1 2 3 4

01 • Press function key [H] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

INFRARED FREQUENCY

This menu allows you to set the infrared frequency.

Factory default is [1].

Note • When more than two sensors are installed in close proximity,

select different frequency settings for each sensor to avoid cross

interference.

A B C D

1 2 3 4

01 • Press function key [↑+ A] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

INFRARED PRESENCE TIME

This menu allows you to set the amount of time

the infrared will detect the same object in its 5

detection lines. Factory default is [1].



Sec. 

MIN 

MIN 

MIN 

MIN 

MIN 

H

H

1 2 3 4 5 6 7 8 9

01 • Press function key [↑+ B] .

02 • Press the numeric key to change the value.

03 • Press #to save the new value.

Detection lines and detection width can be set independently. Like for example:

L R

 lines













     

Inhaltsverzeichnis

Andere Motorline professional Toröffner Handbücher

Motorline professional

Motorline professional KVM105 Bedienungs- und Installationshandbuch

Motorline professional

Motorline professional FIX Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional J400 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional Gateway Control SLIDE 500 Bedienungsanleitung

Motorline professional

Motorline professional KVM205 Bedienungsanleitung

Motorline professional

Motorline professional LINCE Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional SIGMA X Bedienungsanleitung

Motorline professional

Motorline professional OL1500 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional BRAVO500-50 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional SPIN Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional LINCE400 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional MC62 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional PERGOLA Bedienungs- und Installationshandbuch

Motorline professional

Motorline professional LINCE300 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional TEC100 Bedienungs- und Installationshandbuch

Motorline professional

Motorline professional MC50SC Bedienungsanleitung

Motorline professional

Motorline professional KFM Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional LINCE Series Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional JAG400 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional MC52 Bedienungsanleitung

Motorline professional

Motorline professional FORT Bedienungsanleitung

Motorline professional

Motorline professional LINCE Series Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional LINCE 300 Bedienungsanleitung

Motorline professional

Motorline professional TELICA Gebrauchs- und Pflegehandbuch

Beliebte Toröffner Handbücher anderer Marken

CAME

CAME FROG-PM4 Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Erreka

Erreka BUL BL33 Betriebsanleitung

Erreka

Erreka VULCAN S Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Erreka

Erreka VULCAN D Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

CAME

CAME F500 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung

Comunello Automation

Comunello Automation ABACUS 220 Bedienungsanleitung

CAME

CAME FA40230CB Bedienungsanleitung

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Bedienungsanleitung

Riello Elettronica

Riello Elettronica CARDIN ACE FAST Handbuch