Motorola AP6532 Bedienungsanleitung

AP6532 Series Access Point

Installation Guide

MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Sym-

bol is a registered trademark of Symbol Technologies, Inc. All other product or service names are

1 Introduction .......................................................................................... 1

1.1 Document Conventions .......................................................................................... 1

1.2 Warnings ................................................................................................................ 1

1.3 Site Preparation...................................................................................................... 2

1.4 AP6532 Package Contents ..................................................................................... 2

1.4.1 External Antenna Model Package Contents ............................................... 2

1.4.2 Integrated Antenna Model Package Contents............................................ 2

1.5 Features.................................................................................................................. 3

2 Hardware Installation ........................................................................ 4

2.1 Installation Instructions.......................................................................................... 4

2.2 Precautions............................................................................................................. 5

2.3 Access Point Placement ......................................................................................... 5

2.4 Integrated Antenna Model Wall Mount Instructions ............................................ 5

2.4.1 Wall Mount Hardware ................................................................................ 5

2.4.2 Wall Mount Procedure ................................................................................ 7

2.5 Integrated Antenna Model Suspended Ceiling T-Bar Mount Instructions ............ 9

2.5.1 Suspended Ceiling Mount Procedure.......................................................... 9

2.6 External Antenna Model Wall Mount Instructions.............................................. 10

2.6.1 Wall Mount Hardware .............................................................................. 10

2.6.2 Wall Mount Procedure .............................................................................. 11

2.7 External Antenna Model Suspended Ceiling Tile (Plenum) Mount Instructions . 12

2.7.1 Suspended Ceiling Mount Hardware........................................................ 12

2.7.2 Ceiling Mount Procedure........................................................................... 13

2.8 AP6532 External Antenna Model Antenna Options............................................. 14

2.9 LED Indicators....................................................................................................... 15

Table of Contents

3 Defining a Basic Configuration ...................................................... 16

3.1 Using the Initial Setup Wizard ............................................................................. 16

4 Specifications.................................................................................... 37

4.1 AP6532 External Antenna Model Electrical Characteristics................................ 37

4.2 AP6532 External Antenna Model Physical Characteristics ................................. 37

4.3 AP6532 Integrated Antenna Model Electrical Characteristics ............................ 38

4.4 AP6532 Integrated Antenna Model Physical Characteristics.............................. 38

4.5 Radio Characteristics ........................................................................................... 39

5 Regulatory Information..................................................................... 40

5.1 Regulatory Information......................................................................................... 40

5.2 Wireless Device Country Approvals..................................................................... 40

5.2.1 Country Selection...................................................................................... 41

5.2.2 Frequency of Operation – FCC and IC ....................................................... 41

5.3 Health and Safety Recommendations.................................................................. 41

5.3.1 Warnings for Use of Wireless Devices..................................................... 41

5.3.2 Potentially Hazardous Atmospheres – Fixed Installations ....................... 41

5.3.3 Safety in Hospitals.................................................................................... 42

5.3.4 Pacemakers ............................................................................................... 42

5.3.5 Other Medical Devices.............................................................................. 42

5.4 RF Exposure Guidelines........................................................................................ 42

5.4.1 Safety Information..................................................................................... 42

5.5 International ......................................................................................................... 42

5.6 Europe................................................................................................................... 43

5.7 US and Canada..................................................................................................... 43

5.8 Power Supply........................................................................................................ 43

5.9 Radio Frequency Interference Requirements—FCC ............................................ 44

5.10 Radio Frequency Interference Requirements – Canada ................................... 44

5.10.1 Radio Transmitters.................................................................................. 44

5.11 CE Marking and European Economic Area (EEA) ............................................... 45

5.12 Statement of Compliance................................................................................... 45

5.13 Waste Electrical and Electronic Equipment (WEEE) .......................................... 46

5.14 TURKISH WEEE Statement of Compliance ........................................................ 47

5.15 Japan (VCCI) - Voluntary Control Council for Interference ................................ 47

5.16 Korea Warning Statement for Class B ITE......................................................... 48

5.17 Other Countries .................................................................................................. 48

5.17.1 Australia.................................................................................................. 48

5.17.2 Brazil........................................................................................................ 48

5.17.3 Chile ........................................................................................................ 48

5.17.4 China........................................................................................................ 49

5.17.5 Mexico..................................................................................................... 49

5.17.6 South Korea............................................................................................. 49

5.17.7Taiwan ..................................................................................................... 50

6 Motorola Solutions Enterprise Mobility Support Center ........... 51

6.1 Customer Support Web Sites............................................................................... 51

6.2 Manuals................................................................................................................ 51

7 AP6532 Series ROHS Compliance .................................................. 52

Introduction 1

1 Introduction

The AP6532 Access Point, a component of the Motorola Solutions Wireless Controller System, links

wireless 802.11a/b/g/n devices to the controller, enabling growth of your wireless network with a

costeffective alternative to standard Access Points. The AP6532 Access Point provides two

placement options: wall and ceiling. Wall mount slots fit onto two provided screws. Arrows on the

case guide the placement of the screws. For placement above a suspended ceiling, a safety wire tie

point on the case provides for a safety wire loop. The light pipe fits through a hole in the ceiling tile

to provide a view of the unit’s status lights.

The AP6532 Access Point receives all power and transfers data through the same CAT-5 or better

Ethernet cable. There is no additional power supply required. An 802.3af Ethernet switch or power

injector is required.

1.1 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

1.2 Warnings

• Read all installation instructions and site survey reports, and verify correct equipment

installation before connecting the AP6532 Access Point.

• Remove jewelry and watches before installing this equipment.

• Verify that the unit is grounded before connecting it to the power source.

• Verify that any device connected to this unit is properly wired and grounded.

NOTE Tips, hints, or special requirements that you should take note of.

CAUTION Care is required. Disregarding a caution can result in data loss or

equipment malfunction.

WARNING! Indicates a condition or procedure that could result in personal injury or

equipment damage.

AP6532 Series Access Point: Installation Guide

• Verify there is adequate ventilation around the device, and that ambient temperatures meet

equipment operation specifications.

1.3 Site Preparation

• Consult your site survey and network analysis reports to determine specific equipment

placement, power drops, and so on.

• Assign installation responsibility to the appropriate personnel.

• Identify and document where all installed components are located.

• Ensure adequate, dust-free ventilation to all installed equipment.

• Identify and prepare Ethernet and console port connections.

• Verify that cable lengths are within the maximum allowable distances for optimal signal

transmission.

1.4 AP6532 Package Contents

The AP6532 Access Point is available in integrated antenna and external antenna models. The

contents of the package differ between the integrated antenna and external antenna model.

1.4.1 External Antenna Model Package Contents

• AP6532 Access Point with external antenna connectors (Plenum Rated)

• Two wall mount screws

• Two wall anchors

• Light pipe

• Badge for light pipe

• AP6532 Installation Guide (This Guide)

1.4.2 Integrated Antenna Model Package Contents

• AP6532 Access Point with integrated antennas

• Two wall mount screws

• Two wall anchors

• AP6532 Installation Guide (This Guide)

Introduction 3

1.5 Features

• One RJ-45 connector

• LED indicators

• Safety wire tie point

• Slots for wall mounting

• Clips for mounting on a suspended ceiling T-bar

• Lock port for Kensington® style Security Lock

The AP6532 Access Point has one RJ-45 connector supporting an 10/100/1000 Ethernet port and

requires 802.3af-compliant power from an external source.

The AP6532 Access Point comes with dual radios both supporting 802.11a/b/g/n.

The Access Point contains runtime firmware which enables the unit to boot after a power up or

watchdog reset. The runtime firmware on the Access Point and the firmware downloaded from the

controller can be updated via the Ethernet interface from the Wireless Controller.

NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

is recommended for Gigabit operation.

AP6532 Series Access Point: Installation Guide

2 Hardware Installation

2.1 Installation Instructions

The AP6532 Access Point mounts either on a wall (with wide-shoulder screws) or on a suspended

ceiling T-bar. This unit is not designed for mounting on a desk.

To prepare for the installation, perform the following:

1. Match the model number on the purchase order with the model numbers in the packing list

and on the case of the device shipped.

2. Verify the contents of the box include the intended AP6532 Access Point and that the

included hardware matches the package contents on page 2.

3. Review site survey and network analysis reports to determine the location and mounting

position for the AP6532 Access Point.

Part Number Description

AP-6532-66030-US 802.11a/b/g/n dual radio integrated antenna configuration

United States model

AP-6532-66030-OUS 802.11a/b/g/n dual radio integrated antenna configuration

United States model for outdoor installation

AP-6532-66030-WW 802.11a/b/g/n dual radio integrated antenna configuration

World Wide model

AP-6532-66040-US 802.11a/b/g/n dual radio external antenna configuration

United States model

AP-6532-66040-OUS 802.11a/b/g/n dual radio external antenna configuration

United States model for outdoor installation

AP-6532-66040-WW 802.11a/b/g/n dual radio external antenna configuration

World Wide model

NOTE In the above part numbers, XX represents the 2-digit country code which

specifies which country the model is designed for. A country code of

“WW” represents a world wide model. The letter O preceding the 2-digit

country code specifies the model is designed for outdoor installation.

Hardware Installation 5

4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3af power source and run the

cable to the installation site. Ensure there is sufficient slack on the cable to perform the

installation steps.

2.2 Precautions

Before installing an AP6532 model Access Point, verify the following:

• Motorola Solutions recommends you do not to install the AP6532 in wet or dusty areas.

• Verify the environment has a continuous temperature range between 0° C to 50° C.

2.3 Access Point Placement

For optimal performance, install the Access Point away from transformers, heavy-duty motors,

fluorescent lights, microwave ovens, refrigerators and other industrial equipment. Signal loss can

occur when metal, concrete, walls or floors block transmission. Install the Access Point in an open

area or add Access Points as needed to improve coverage.

Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright

enough. An area lit sharply might minimize coverage and create dark areas. Uniform antenna

placement in an area (like even placement of a light bulb) provides even, efficient coverage.

Place the Access Point using the following guidelines:

• Install the Access Point at an ideal height of 10 feet from the ground.

• Orient the Access Point antennas vertically for best reception.

To maximize the Access Point’s radio coverage area, Motorola Solutions recommends conducting a

site survey to define and document radio interference obstacles before installing the Access Point.

2.4 Integrated Antenna Model Wall Mount Instructions

This mounting requires hanging the AP6532 Access Point along its width or length using the two slots

on the bottom of the unit. The AP6532 can be mounted onto any plaster, wood, or cement wall surface

using the provided wall anchors. The following illustration displays a lengthwise mount.

2.4.1 Wall Mount Hardware

• Two wide-shoulder Phillips pan head self-tapping screws

NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

is recommended for Gigabit operation.

Andere Handbücher für AP6532

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Motorola Drahtloser Zugangspunkt Handbücher

Motorola

Motorola AP-7131 Series Installations- und Betriebshandbuch

Motorola

Motorola CB3000 - Client Bridge - Wireless Access... Bedienungsanleitung

Motorola

Motorola PMP 320 Bedienungsanleitung

Motorola

Motorola AP6562 Bedienungsanleitung

Motorola

Motorola WiNG 5.6 Bedienungsanleitung

Motorola

Motorola Verizon VAP2500 Bedienungsanleitung

Motorola

Motorola MotoWI4 PTP 600 Series Bedienungsanleitung

Motorola

Motorola AP-8132 Bedienungsanleitung

Motorola

Motorola 5750APUSG Bedienungsanleitung

Motorola

Motorola AP 7181 Bedienungsanleitung

Motorola

Motorola AP-7131N-FGR Installations- und Betriebshandbuch

Motorola

Motorola AP-51 Series Installations- und Betriebshandbuch

Motorola

Motorola AP 7161 Bedienungsanleitung

Motorola

Motorola AP 5131 - Wireless Access Point Bedienungsanleitung

Motorola

Motorola 5440AP - Canopy 5.4 GHz AP Betriebsanleitung

Motorola

Motorola PTP 600 Series Bedienungsanleitung

Motorola

Motorola AP-7131N-FGR Bedienungsanleitung

Motorola

Motorola PMP 100 Bedienungsanleitung

Motorola

Motorola AP-7131N-FGR Bedienungsanleitung

Motorola

Motorola WA840GV2 Bedienungsanleitung

Motorola

Motorola AP-0622 Bedienungsanleitung

Motorola

Motorola WS2000 - Wireless Switch - Network Management... Bedienungsanleitung

Motorola

Motorola AP-7131 Series Anleitung zur Verwendung

Motorola

Motorola WiNG 5.4.2 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung