Motorola MC-802 Bedienungsanleitung

USER GUIDE

MC-802 Wireless WallPlate

No part of this publication may be reproduced or transmitted, in any form or by any means, electronic,

mechanical, photocopying, recording, or otherwise, without the prior written consent of the publisher.

Information in this manual is furnished under license and may only be used in accordance with the terms

of the software license. This publication and the information herein is furnished AS IS, is subject to

change without notice, and should not be construed as a commitment by Motorola. Motorola assumes no

responsibility or liability for any errors or inaccuracies, makes no warranty of any kind (expressed, implied,

or staory) with respect to this publication, and expressly disclaims any and all warranties of

merchantability, fitness for particular purposes, and noninfringement of third-party rights.

Companies, names, and data used in the examples herein are fictitious unless otherwise noted.

Pass-Through Licenses:

Net-SNMP and LwIP source code are provided under the terms of their respective license agreements.

Source code and copyright notices are available at http://motorolaonline.com

‘Motorola‘ is a registered trademark of Motorola, Inc. in the United States and in other countries.

Other trade names used in this document are trademarks or registered trademarks of the manufacturers

or vendors of the associated products.

Motorola, Inc.

5200 Franklin drive, Suite 100

Pleasanton, CA 94588

1 (925) 201-4500 main

1 (925) 201-4509 fax

1 (800) 998-4888

www.systems.com

Published in the United States of America

August, 2007

MC-802 Wireless WallPlate User Guide

Text part number:

FCC Part 15A

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

IMPORTANT SAFETY INSTRUCTIONS

MC-802

CAUTION: Use only power supplies listed in the user manual

The maximum operating ambient temperature is 40 degrees Celsius.

When using your telephone equipment, basic safety precautions should always be followed to reduce the

risk of fire, electric shock and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry

tub, in a wet basement or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote

risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

SAVE THESE INSTRUCTIONS

Caring for the Environment by Recycling

When you see this symbol on a Motorola product, do not dispose of the product with residential or

commercial waste.

Recycling your Motorola Equipment

Please do not dispose of this product with your residential or commercial waste. Some

countries or regions, such as the European Union, have set up systems to collect and

recycle electrical and electronic waste items. Contact your local authorities for information

about practices established in your region. If collection systems are not available, contact

Motorola Customer Service for assistance.

WEEE Directive

Motorola is committed to meeting the requirements of the European Union’s Waste Electrical and

Electronic Equipment (WEEE) Directive. This Directive requires producers of electrical and electronic

equipment to finance the take-back for re-use or recycling, of their products placed on the EU market

after 13 August 2005.

Motorola’ products that are within the scope of the Directive are labeled with a crossed-out "wheelie-bin"

symbol as required by the Directive. This indicates that the product was placed on the market after 13

August 2005 and that end-users should segregate the product from other wastes at end-of-life.

Legislation in conformance with the European Commission 2002/96/EC (WEEE) directive can vary from

one member state to the next. Provisions in force in one state do not render another state’s legislation

invalid or convey further requirements than proscribed in the individual state’s legislation.

Product Take-Back and Recycle

Legislative and environmental factors combined with the competitive drive to implement the latest

technology present many companies with the challenge of managing technology surpluses. Motorola

offers customers the Motorola WEEE RMA program to properly dispose of surplus products that have

reached their end of useful life.

Equipment that is returned to Motorola through this program is disposed of in an environmentally safe

manner using processes that comply with the WEEE (EU Directive on Waste Electrical and Electronic

Equipment) regulations, all EPA guidelines, and U.S. environmental laws at all levels of government.

Motorola’ branded products covered by the WEEE RMA program are labeled with a cross-out “wheelie-

bin” symbol as required by the Directive.

WEEE RMA Program

The MC-802 Wireless WallPlate is covered by the WEEE RMA program and subject to the requirements

of the B2B (business to business) provisions of the WEEE legislation in each EC member state. A copy

of the WEEE RMA form can be obtained by emailing [email protected].

RoHS Directive

The MC-802 Wireless WallPlate sold to the European Union after July 1, 2006 meet requirements of the

European Union’s Restriction of Hazardous Substances (RoHS) Directive. RoHS restricts the use of

lead, mercury, cadmium, hexavalent chromium and two bromine-containing flame retardants: PBB

(polybrominated biphenyls) and PBDE (polybrominated diphenyl ethers) in electrical and electronic

products placed on the European Market on and after July 1, 2006. Exemptions allow the continued use

of lead in networking infrastructure equipment and a few select components.

Motorola is working closely with its supply chain to assure compliance of all product and materials

provided by our suppliers and partners.

Commands and Syntax 6

Command Hierarchy.................................................................................. 6

Administrative Commands.......................................................................... 6

Hardware 8

Model Numbers and Description for MC-802.................................................. 8

Model Numbers and Description for related Products ...................................... 8

Wireless WallPlate..................................................................................... 9

System Administration 9

Management Access .................................................................................. 9

WallPlate Installation 10

Enable line power.................................................................................... 12

Finish the installation............................................................................... 12

Command Reference 13

Appendix A: Pin-out Assignments 14

Appendix B: Hardware Specifications 15

Commands and Syntax

The Motorola MC-802 is managed via the Command Line Interface, webUI, and SNMP from a connected

Motorola mT2a EthernetXD Switch. All commands referenced are executed on the mT2a.

The Command Line Interface (CLI) implements a hierarchical command structure. Commands are

organized as a high-level command keyword related to a particular function of the device with sub-

commands related to sub-functions.

You may move down in the command hierarchy by entering root keywords and sub-keywords followed by

the enter key. Your current level in the command hierarchy is referred to as the “command context.” The

top-level context is referred to as the “root command context.” You may move up to the previous

command context by using the exit command. The command prompt displays the current command

context.

Full commands may be entered at the root command context. For example:

system> interface dsl enable port1

You may also move down levels in the command hierarchy, which allows you to execute commands with

less repetitive typing.

For example:

system> interface

system:interface> dsl

system:interface.dsl> enable port1

system:interface.dsl> enable port2

system:interface.dsl> enable port3

system:interface.dsl> exit

system:interface> exit

system>

Most commands discussed in this guide are administrative commands, which change the configuration of

the system or affect the operation of the system. These commands can only be executed from the admin

account. Configuration changes take affect immediately and are recorded in non-volatile memory

(NVRAM) in the default mode. Alternatively, you may choose not to record changes in NVRAM. In this

case, changes will need to be committed before rebooting the system; otherwise the configuration will

revert to the last saved configuration. If automatic commit is enabled, or the configuration is manually

committed, the running configuration will automatically be restored if the system power cycles or is

rebooted.

Show Commands

The show commands are used to view configurations, status and/or statistics. These commands can be

issued from either the user or admin account.

Commands and Syntax

Global Commands

Commands that are available from any command context are called global commands. For example, the

help command can be used whether you are at the root command context or down a few levels in the

command hierarchy. Global commands can also be used from either the user or admin account.

Note: The default prompt is “system>”. If you set the system name using the “system name”

command, the prompt changes to the new system name.

Command Description

clear Clears the screen

exit Use this command to switch to the previous context. Note that using the exit

command at the root command contgext performs the same function as logout.

help Displays the help files

history Shows the history of the commands used in the current session.

logout Can be used with either the login (admin, user, RADIUS network authenticated) and

at any command level to terminate the current session

tree Shows the structure of the command tree

Command Completion

The OS allows you to shorten commands as long as the characters are not ambiguous. While typing a

command, press the tab key to have the system complete the current command word or type (?) to have

the system display a list of available options. The options displayed vary according to the context:

• If you type a ? at a prompt, the system displays a list of all available commands.

• If you type an unambiguous command word, pressing ? displays all available subcommands or

arguments. For example, show ? (note the space before the question mark) displays a list of all show

subcommands.

Style Conventions

The style conventions used in this manual distinguish various elements of the commands and facilitate

the proper interpretation of command syntax, parameters, and their use.

This document refers to actual command syntax as little as possible. For a complete command syntax

document, please refer to the Command Reference guide for a complete list of all available commands,

the proper syntax, and usage examples. In no way does this User Guide attempt to replace or obsolete

the Command Reference.

Interface Range

Multiple interfaces can be specified for a single command using port ranges. Use of hyphens (-) and

commas (,) to delineate ports. Port numbers must be contained in parenthesis. Hyphens and commas

can be combined in the same expression to specify multiple, non-sequential interfaces. For example;

To enable all 25 DSL ports, type: interface dsl enable port(1-25)

To enable only selected DSL ports, type: interface dsl enable port(1,3,5,20-25)

Hyphens and commas can also be used to enable remote Ethernet ports along with DSL ports. For

example;

To enable Eth1 and Eth2 on every WallPlate, type: interface remote enable port(1-25)-(1,2)

VLAN commands can also be completed using interface ranges.

To add VLAN 100 to Eth1 on every WallPlate, type: vlan membership add 100 interface port(1-25)-1

Installation Steps

C-

-8

Model Number Description

45010 MC-802 Wireless WallPlate. 1 x 802.11 b/g radio, 2 x Fast Ethernet, 1 x high

speed DSL port, 1 x analog POTS RJ11 port. Designed for installation over

existing RJ11 wall jack. RoHS compliant.

Each MC-802 requires a 45125 to provide connectivity and power. Filters are required for proper in-room

installation. Any installation of the MC-802 may also use one or more of the following additional products.

Model Number Description

45125 25 port mT2a EthernetXD Switch. 2 x GigE uplink Ethernet ports and 25 x high

speed DSL ports for connection to UTP wiring. Provides broadband data and

Adaptive Line Power for remote WallPlate. RoHS compliant.

45101 2 port m2a WallPlate. 2 x Fast Ethernet ports, 1 x high speed DSL port, 1 x

analog POTs RJ11 port. Two powering options; Adaptive Line Power from the

45125 switch, or local power adapter. Designed for installation over existing

RJ11 wall jack. RoHS compliant.

45003 4 port m4a WallPlate. 4 x Fast Ethernet ports, 1 x high speed DSL port, 1 x

analog POTs RJ11 port. Two powering options; Adaptive Line Power from the

45025 switch, or local power adapter. Designed for installation over existing

RJ11 wall jack. RoHS compliant.

45002 4 port m4 Service Unit. 4 x Fast Ethernet ports and 1 x high speed DSL port.

Two powering options; Adaptive Line Power from the 45025 switch, or local

power adapter. Analog POTS filter and port is not included. Solid backplate, not

designed for installation over existing RJ11 wall jack. RoHS compliant.

65601 In-line RJ11 filter, mT2a. RoHS compliant

65602 In-line unterminated filter, mT2a. RoHS compliant

65002 12VDC regulated power supply, US. RoHS compliant

65102 12VDC regulated power supply, Euro. ROHS compliant

61299 RJ11 telephone cable, 2m. RoHS compliant

Installation Steps

MC-802 Wireless WallPlate

Optional adapter plate allows the installer to adapt installation over a standard RJ11 wall plate, reusing

the existing mounting screws.

This User Guide covers the commands relevant to the MC-802. For a complete set of commands and

information; consult the mT2 Command Reference and mT2 User Guide.

mT2 can be managed via serial console, telnet, HTTP web UI, or SNMP. With the 1.3 firmware, Eth1 is

enabled by default. Telnet and HTTP are accessible at the default IP address.

Access Methods

Default IP address 192.168.1.3

Serial console Terminal settings: 9600-8-N-1 no flow control

Telnet Requires Eth1 or Eth2 enabled and a valid IP address

HTTP Requires Eth1 or Eth2 enabled and a valid IP address

Browser support: IE6 or greater, Mozilla

Management URL: http://<IP address>

Default login and password

Default user name for administrative access: admin

Default password: <blank>

Default user name for monitoring only: user

Eth1 – 10/100 auto-sensing Ethernet

Eth2 – 10/100 auto-sensing Ethernet

RJ11 filtered phone port

DC power connector (used during installation)

Installation Steps

Default password: <blank>

Tools Required:

Number 2 Philips head screwdriver

Note: if using a power drill, set the torque clutch to 5 in-lbs.

Components provided with the MC-802 WallPlate:

1 – MC-802 WallPlate

1 – RJ11 wall jack mounting adapter

1 – 150mm (6”) RJ11 pigtail cable

1 – RJ11 blanking plug

2 – 6-32 thread forming Philips head screws, 0.375”

Components required to purchase:

Regulated 12V power supply. Use of the wrong power supply could result in damage to your WallPlate

unit. Please order a small quantity of regulated 12V power supplies from Motorola PBN to use during

installation.

If you do not have the correct regulated 12V power supply – STOP. Order a regulated 12V power supply

from your Motorola PBN sales representative.

Step 1

1. Loosen screws on wall plate approximately 6mm (1/4”)

2. Attach the bracket using the keyhole slots

3. Tighten screws until the bracket is firmly attached, do not over tighten

Inhaltsverzeichnis

Andere Motorola Drahtloser Zugangspunkt Handbücher

Motorola

Motorola AP 7181 Bedienungsanleitung

Motorola

Motorola TLN3221B Bedienungsanleitung

Motorola

Motorola AP 6522M Bedienungsanleitung

Motorola

Motorola AP-8132 Bedienungsanleitung

Motorola

Motorola PMP 320 Bedienungsanleitung

Motorola

Motorola AP6562 Bedienungsanleitung

Motorola

Motorola MotoWI4 PTP 600 Series Bedienungsanleitung

Motorola

Motorola AP-5181 - Wireless Access Point Kurzanleitung

Motorola

Motorola WiNG 5.7.1 Bedienungsanleitung

Motorola

Motorola AP-6511 Bedienungsanleitung

Motorola

Motorola AP 7161 Bedienungsanleitung

Motorola

Motorola AP6532 Bedienungsanleitung

Motorola

Motorola WA840G Bedienungsanleitung

Motorola

Motorola WA840G Bedienungsanleitung

Motorola

Motorola AP 7181 Bedienungsanleitung

Motorola

Motorola VAP2500 Bedienungsanleitung

Motorola

Motorola AP-8132 Bedienungsanleitung

Motorola

Motorola Canopy 300 Mbps Backhaul Bedienungsanleitung

Motorola

Motorola AP-51 Series Installations- und Betriebshandbuch

Motorola

Motorola P-7131N-FGR Installations- und Betriebshandbuch

Motorola

Motorola AP-51XX Installations- und Betriebshandbuch

Motorola

Motorola AP-6521 Series Bedienungsanleitung

Motorola

Motorola PTP 600 Series Bedienungsanleitung

Motorola

Motorola WA840G Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung