Moulinex Kaseo Bedienungsanleitung

PUSH

18 22 23* 24*

21*

19*

20*

25*

26*

27*

fig.2

fig.5

fig.9

fig.16

fig.6

fig.15

fig.10

fig.11

fig.7

fig.13

fig.14

fig.12

fig.8

fig.17

fig.21

fig.18

fig.22

fig.23

fig.19

fig.24

fig.20

fig.4

fig.3

fig.1

SAFETY RECOMMENDATIONS

For your safety, thisappliance conformsto

the applicable standardsand regulations

(Low Voltage, Electromagnetic Compatibility,

Environmental, etc. Directives).

1. CONDITIONSOF USE

• Your vacuum cleaner isan electrical

appliance: it must only be used under

normal operating conditions.

• The appliance should be used and stored

out of the reach of children. Never leave

the appliance unattended when it is

switched on.

• Alwayskeep nozzlesand tube endswell

away from eyesand ears.

• Do not vacuum wet surfaces, any water

or any kind of liquids, hot substances,

ultra-fine substances (plaster, cement,

ash, etc.) large sharp debris (glass),

dangerous products (solvents, stripping

compounds, etc.), chemical products

(acids, cleaners, etc.), inflammable or

explosive products (petrol- or alcohol-

based).

• Do not immerse the appliance in water,

splash water on the appliance or store it

outdoors.

• Do not use the appliance if it has been

dropped and showssignsof damage or

functionsabnormally. In thiscase do not

open the appliance and call our helpline

(overleaf). In thiscase, do not open the

appliance, but send it to the nearest

Approved Service Centre or contact

Moulinex Customer Service (see contact

particularson last page).

2. ELECTRICAL POWER SUPPLY

• Make sure that the operating voltage of

your vacuum cleaner isthe same as your

supply voltage - 230-240v.

• Disconnect the appliance by removing

the plug from the power outlet:

- immediately after use,

- before changing accessories,

before cleaning, care or changing filters.

• Do not use the appliance:

- if the supply cord isdefective. For your

safety, supply cordsand winding systems

must, in all cases, be replaced by our

approved Service Centre.

3.REPAIRS

Repairsshould only be carried out by

specialistsusing original replacement parts.

It isdangerousto try to repair an appliance

by yourself.

DESCRIPTION

a- Horizontal parking

b - Upright parking

Locking button of the air outlet grill

Retractable handle

Automatic cord winder pedal

Dust collection container

Trapdoor of the dust compartment

On/Off pedal

Dust compartment unlock button

Air outlet grill

Filtration system saturation light indicator

Dust collection container handle

Push button to open the dust collector

Dust collector compartment

Suction opening

Air outlet filter ref. MT0002 01

HEPA filter ref. MT0002 01

Nylon pre-filter

10.

11.

12.

13.

14.

15.

16.

17.

Standard accessories:

Flexible tube with extra-long handle and

manual suction power regulator

Telescopic tube*

Tubes*

Floor nozzle*

Automatically adjusting floor head

Upholstery tool*

Crevice tool*

Turbobrush*

Mini turbobrush*

Small brush tool*

18.

19.

20.

21.

22.

23.

24.

25.

26.

27.

*Depending on model: thisiseither equipment

specific to certain modelsor available as an

optional accessory.

BEFORE USING FOR THE FIRST TIME

1. REMOVE PACKAGING

• Take your appliance out of itspackaging.

Keep your warranty card and carefully

read the operating instructionsbefore

using your appliance for the first time.

2. HINTSAND PRECAUTIONS

• Before each use, the supply cord should

be completely unwound.

• Do not allow it to become pinched or

pulled over sharp edges.

• If you use an electric extension cord, make

sure that it isin perfect condition and

appropriate to the power rating of your

appliance.

• Never unplug the appliance by pulling on

the cord.

• Never operate the vacuum cleaner

without the dust collector and without the

filtration system (cassettes).

• Only use filtersby Moulinex.

• Alwaysstop and unplug your appliance

before care or cleaning.

USING THE APPLIANCE

ASSEMBLING THE ELEMENTSOF THE APPLIANCE

• Push the flexible hose (18) in the opening

(14) until your hear aclicking sound - fig.1.

To remove it, press the button of the hose

connector and pull - fig.2.

• Assemble the telescopic tube* (19). Adjust

it to the desired length - fig.3.

• Fit the appropriate accessory to the end

of the tube:

- For rugsand wall-to-wall carpeting: use the

head (22) with brusheslifted - fig.4.

- For parquetsand smooth flooring: use the

nozzle (22) with the brush extended - fig.4.

or use the parquet nozzle* (21).

- For cornersand other areas that are

difficult to reach, use the crevice tool* (24)

- For furniture,use the small brush tool* (27) or

the upholstery tool* (23).

2. PLUGGING IN THE ELECTRICAL POWER

CORD AND USING THE VACUUM CLEANER

• Completely unwind the power cord, plug

in your vacuum cleaner and push the

on/off pedal (7) - fig. 5.

• Adjust the suction power on the power

nozzle with the mechanical power control

(18). Open the manual suction regulator to

reduce the suction power manually – for

fragile surfaces, for example.

STORING AND TRANSPORTING THE APPLIANCE

• After use, stop your appliance by pressing

on the on/off pedal (7) and unplug it

- fig. 6.

Replace the cable by pressing the

automatic cord winder pedal

(4) - fig. 7.

• In the horizontal position, hook the floor

nozzle (22) onto itsstorage position at the

rear of the appliance (1a).

• You can transport your vacuum cleaner

easily by meansof itsretractable handle

(3).

• In an upright position, hook the telescopic

tube* (19) onto itsstorage position on the

back of the appliance (1b).

CARE AND CLEANING

1. EMPTYING THE DUST COLLECTOR

• Alwaysswitch off and unplug your vacuum

cleaner before servicing or cleaning it.

• Empty the dust collector after every use

(5).

• Press the dust collector unlock button (8)

of your vacuum cleaner, and lift the

dust collector to remove it from its

compartment (13)

- fig. 8.

• Over your waste bin, press the push-open

button of the dust collector (12) and

empty it - fig. 9.

•

Clean the rimsof the dust collector - fig. 10.

• Fit the dust collector back in its

compartment (13) until it engageswith a

click - fig. 11.

• After cleaning, correctly put the filtration

system back in place.

CLEANING THE HEPA FILTER (REF.MT0002 01)

• The light indicator of the filtration system

(10) isred, clean the HEPA (16) filter by

tapping it:

- Press the locking button of the dust

collector (8) of your vacuum cleaner and

lift it to remove it from itscompartment (13)

– fig. 8.

- Remove the HEPA filter (16) from its

compartment – fig. 12.

- Clean the HEPA filter (16): tap it over a

waste bin – fig. 13.

- If after tapping your HEPA filter the indicator

light remainsred, you need to change your

HEPA filter (ref. MT0002 01)

- If the HEPA filter (16) isdamaged,change it.

Throw the HEPA filter (16) into awaste bin –

fig. 13 and change it with anew HEPA filter

(ref. MT0002 01).

- Put the HEPA filter back into its

compartment – fig. 14.

- Put the dust collector (5) back into its

compartment (13) until it engageswith a

click – fig. 11.

3.CLEANING THE NYLON PRE-FILTER

• To clean the nylon pre-filter (17), press the

dust collector unlock button (8) of your

vacuum cleaner and lift it to remove it

from itscompartment (13)

- fig. 8.

• Remove the Hepafilter (16) from its

compartment - fig. 12.

• Remove the nylon pre-filter (17) from its

compartment - fig. 15.

• Empty out the dust retained - fig. 16 and

clean the nylon pre-filter (17) in clean

water - fig. 17.

• Allow the nylon pre-filter to dry completely

(17) before putting it back in place

- fig. 17.

Caution: Make sure that the nylon pre-filter

iscompletely dry before putting it back in

place.

• Put the nylon pre-filter (17) back in its

compartment - fig. 18. Put the Hepafilter

back in itshousing.

• Fit the dust collector (5) back in its

compartment (13) until it engageswith a

click - fig. 11.

4. CLEANING THE AIR OUTLET FILTER

• Lift the retractable handle (3) - fig. 19 and

remove the air outlet grill (9) by lifting the

locking button of the air outlet grill (2)

- fig. 19.

• Remove the air outlet filter (15) - fig. 20.

• Wash and squeeze dry the air outlet filter

(15) and allow it to dry for at least 12 hours

- fig. 21.

• Put the air outlet filter back (15) - fig. 22.

• You can also change the air outlet filter

(15) (ref. MT0002 01).

• Fit the air outlet grill (9) until it engageswith

aclick - fig. 23.

5. CLEAN THE VACUUM CLEANER

• Clean the housing of the vacuum cleaner

with asoft and humid rag and let dry with

adry rag - fig. 24.

• Wash the dust collector (5) in clean water

and then dry it. Check that the dust

collector iscompletely dry before putting

it back in place.

Caution: Make sure that the dust collector

iscompletely dry before putting it pack in

place.

• Do not use abrasive or aggressive

products.

WARRANTY

• Thisproduct has been designed for

domestic use only. Any professional use,

innapropriate use or failure to comply with

the instructions, the manufacturer accepts

no responsibility and the guarantee will not

apply.

• Read the instructionsfor use carefully

before using your appliance for the first

time: any use which doesnot conform to

these instructionswill absolve Moulinex

from any liability.

TROUBLESHOOTING

IF YOUR VACUUM CLEANER DOESNOT START

• The appliance isnot plugged-in, check

that the appliance iscorrectly plugged in.

2. IF THERE ISNO SUCTION

•

An accessory or the tube isclogged.

Unclog the accessory tube or flexible hose.

• If the dust collector isnot correctly locked,

check how it was put back in place.

•

If the nylon pre-filter issaturated, tap it afew

timesand/or wash it.Allow the nylon pre-filter

to dry completely before putting it back in

place.

•

The HEPA filter issaturated, the indicator light

of the filtration system isred: tap the HEPA

filter. If the problem persists,change the

HEPA filter (ref. MT0002 01).

3.IF THE SUCTION OF YOUR VACUUM CLEANER

HASDROPPED,IT MAKESA NOISE AND

WHISTLES

• An accessory or the flexible hose is

partially clogged. Unclog the accessory

tube or flexible hose.

• If the dust collector isfull, empty it and

wash it.

• The filtration system issaturated, the

indicator light of the filtration system isred:

tap the HEPA filter and fit it again. If the

indicator light remainsred, clean the nylon

pre-filter.

If the problem persists,change the filter

HEPA (ref. MT0002 01).

• If the dust collector isnot fully engaged in

itshousing, push it in fully until it engages

with aclick.

• If the mechanical power control of the

power nozzle isopen, close it.

4. IF THE FLOOR NOOZLE ISHARD TO MOVE

AROUND

• Open the mechanical power control of

the power nozzle.

5. IF THE POWER CORD DOESNOT REWIND

COMPLETELY

• The power cord isslow in re-entering its

housing. Pull the cord back out and press

on the automatic cord rewinder pedal.

If problemspersist, take your vacuum

cleaner to the nearest Moulinex approved

Service Center (see list of approved Service

Centers) or contact the Moulinex customer

service (see contact detailson last page).

ENVIRONMENT

• In accordance with current regulations,

before disposing of an appliance no

longer needed, the appliance must be

rendered inoperative (by unplugging it

and cutting off the electricity supply cord).

• Environment: Directive 2002/95/EC.

Environment protection first!



Your appliance containsvaluable materials

which can be recovered or recycled.

Leave it at alocal civic waste collection

point.

THE ACCESSORIES*

ACCESSORIES* VACUUMING PURCHASE

LOCATIONS

Floor nozzle

For hard and smooth

floors.

Moulinex Approved

Service Centres

(see the attached

address list).

Moulinex Approved

Service Centres

(see the attached

address list).

Moulinex Approved

Service Centres

(see the attached

address list).

To clean upholstery

fabricsin depth.

Mini turbobrush

To remove threads

and animal hairs

ingrained into mats

and carpets.

FITTING AN

ACCESSORY

Fit the hardfloor tool to

the end of the tube.

Fit the mini turbobrush

to the end of the tube.

Fit the turbobrush to the

end of the tube.

Turbobrush

*Depending on model: thisiseither equipment

specific to certain modelsor available as an

optional accessory.

Inhaltsverzeichnis

Andere Moulinex Staubsauger Handbücher

Moulinex

Moulinex MO3927PA Bedienungsanleitung

Moulinex

Moulinex Zello Bedienungsanleitung

Moulinex

Moulinex cosmo MO6527 Bedienungsanleitung

Moulinex

Moulinex MX101701 Bedienungsanleitung

Moulinex

Moulinex Principio Bedienungsanleitung

Moulinex

Moulinex MO652711 Bedienungsanleitung

Moulinex

Moulinex compacteo ergo MO5263PA Bedienungsanleitung

Moulinex

Moulinex zelio Bedienungsanleitung

Moulinex

Moulinex MX413701 Bedienungsanleitung

Moulinex

Moulinex Extenso Accessimo MX2217-MO Bedienungsanleitung

Moulinex

Moulinex compacteo ergo cyclonic Bedienungsanleitung

Moulinex

Moulinex compacteo MO152301 Bedienungsanleitung

Moulinex

Moulinex Cosmo Bedienungsanleitung

Moulinex

Moulinex POWERSTYLE Bedienungsanleitung

Moulinex

Moulinex Mini Space MO182301 Bedienungsanleitung

Moulinex

Moulinex accessimo MO151501 Bedienungsanleitung

Moulinex

Moulinex accessio 7.2v Bedienungsanleitung

Moulinex

Moulinex accessimo MO151801 Bedienungsanleitung

Moulinex

Moulinex MO3953PA Bedienungsanleitung

Moulinex

Moulinex HAND-HELD VACCUUM CLEANER Bedienungsanleitung

Moulinex

Moulinex MO4013T1 Bedienungsanleitung

Moulinex

Moulinex Kaseo MO6011T1 Bedienungsanleitung

Moulinex

Moulinex Accessio Bedienungsanleitung

Moulinex

Moulinex dualio Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Moulinex kaseo Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken