Mountup MU0004 Bedienungsanleitung

Single Monitor Counterbalance Desk Mount

Instruction Manual

If you have any questions , please contact us via: [email protected]

75x75

100x100

2~8kg

4.4~17.6lbs

32"

MU0004

V6.0

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of

this product, contact Customer Service via [email protected].

Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or

serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed

weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.

ADULT SUPERVISION IS REQUIRED.

NOTE: Not all hardware included will be used.

DO NOT EXCEED WEIGHT CAPACITY.

WARNING!

PACKAGE CONTENTS

17.6lbs

(8kg)

A (x1)

Arm

C (x1)

Bracket

D (x1)

Clamp

F (x1)

Grommet Base

G (x1)

Wingnut

I (x1)

Bolt

H (x1)

Carriage Bolt

J (x1)

Support Plate

K(x1)

4mm Allen Key

L(x1)

5mm Allen Key

M(x1)

6mm Allen Key

E(x5)

M6x10

B (x1)

VESA Plate

M-C (x4)

D6 Washer

M-A (x4)

M4x12

M-B (x4)

M6x12

M-D (x4)

spacer

OPTION A: Clamp Installation

Mount bracket (C) to bottom of gas spring arm (A) using bolts (E). Tighten using 4mm allen key (K).

Attach clamp (D) to bracket (C) using bolts (E) and 4mm allen key (K). Mount according to thickness of desktop.

Secure stand to desktop by tightening clamp (D) or by using 6mm allen key (M).

ASSEMBLY STEPS

STEP 1: Clamp Installation OR Grommet Base Installation

10-60mm

10-90mm

C C

OPTION B: Grommet Base Installation

For grommet hole mounting, place carriage bolt (H) through the center of grommet base (F). Mount grommet

base to bottom of gas spring arm (A) using bolts (E). Tighten using 4mm allen key (K). Run carriage bolt (H)

through grommet hole in desktop. Attach metal plate (J) and wingnut (G). Tighten wingnut.

STEP 1: (Continued)

STEP 2: Attach Monitor

M-A

M-B

M-C

M-A

M-B

M-C

M-D

OPTION A: Flat Back Monitor

Attach the VESA plate (B) to back of monitor and

secure with screws(M-A)or(M-B) with washers(M-C)

using 6 mm Allen Key (M). Avoid excessive

tightening screws damage the monitor.

CAUTION:To select the correct screws(M-A or M-B)

for your monitor, you can try to screw it on your

monitor by hand. The one can screw inside is the

correct screw for your monitor.

OPTION B: Curved Back Monitor

Attach the VESA plate (B) to back of monitor and secure

with screws (M-A) or (M-B) with washers (M-C)and

spacers(M-D)using 6 mm Allen Key (M). Avoid excessive

tightening screws damage the monitor.

Slide the monitor onto the head of swivel arm, install the security bolt (I). Make sure the security

bolt is installed before you rotate the monitor.

STEP 3: Hang Monitor

Refer to below illustrations to

adjust tilting angle of your monitor.

Note: Fasten/loosen the tilting bolt

as needed per arrow direction (+/-)

shown in above diagram.

STEP 4: Adjust Tension

For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust

tension in gas spring arm (A) using 5 mm allen key (L).

If necessary, refer to above illustrations

to adjust the level of tightness of the

arms.

CAUTION

After being attached to the arm, the monitor falls down

and can not stay at the desired height by itself.

Turn counter-clockwise(“+”direction) to increase gas

spring tension until the monitor can stay at the desired

Height by itself.

After being attached to the arm, the monitor rises up and

can not stay at the desired height by itself.

Turn clockwise(“-”direction) to reduce gas spring tension

until the monitor can stay at the desired Height by itself.

Note：

Be sure to keep the arm in horizontal

position during adjustment. Or else it

would be dicult to adjust the mount

or damage the mount.

STEP 5: Cable Management

Remove bottom plastic covers from gas spring arm(A) as shown in diagram.

STEP 5: (Continued)

Run cables from monitor through bottom of gas spring arm (A). Reattach plastic covers as shown in diagram.

Adjust as Desired

DESK DESK

Pay attention while clamp install !

Note: When tilted, if the monitor sags or does not stay,

please fasten the tilting bolt on the mount until the

monitor can be held at any angle as needed.

360°

+90°

-45°

180°

Andere Handbücher für MU0004

Inhaltsverzeichnis

Andere Mountup Rack & Stand Handbücher

Mountup

Mountup MU1005 Bedienungsanleitung

Mountup

Mountup MU0026 Bedienungsanleitung

Mountup

Mountup MU0045 Bedienungsanleitung

Mountup

Mountup MU0006 Bedienungsanleitung

Mountup

Mountup MU0033 Bedienungsanleitung

Mountup

Mountup MU0024 Bedienungsanleitung

Mountup

Mountup MU4003 Bedienungsanleitung

Mountup

Mountup MU0060 Bedienungsanleitung

Mountup

Mountup MU0011 Bedienungsanleitung

Mountup

Mountup MU2005 Bedienungsanleitung

Mountup

Mountup MU0029 Bedienungsanleitung

Mountup

Mountup MU0021 Bedienungsanleitung

Mountup

Mountup MUA6008B Bedienungsanleitung

Mountup

Mountup MU0002 Bedienungsanleitung

Mountup

Mountup MU5001 Bedienungsanleitung

Mountup

Mountup MU6001 Bedienungsanleitung

Mountup

Mountup MU5004 Bedienungsanleitung

Mountup

Mountup MU0014 Bedienungsanleitung

Mountup

Mountup MU0014 Bedienungsanleitung

Mountup

Mountup MU0022 Bedienungsanleitung

Mountup

Mountup MU7012 Bedienungsanleitung

Mountup

Mountup MU6003 Bedienungsanleitung

Mountup

Mountup MU2001 Bedienungsanleitung

Mountup

Mountup MU6002 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung