Mountup MU0027 Bedienungsanleitung

MU0027 1.5~8kg

(3.3~17.6lbs)

RATED

If you have any questions , please contact us via: [email protected] V1.0

Gaming Counterbalance Desk Mount

Instruction Manual

PRODUCT LINE GRAPH

WARNING!

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of

this product, contact Customer Service via [email protected].

Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or

serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed

weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.

ADULT SUPERVISION IS REQUIRED.

300mm

75mm

100mm

115mm

75mm

100mm

115mm

189mm 208~281mm 62mm

min10~max85mm

min187~max487mm

min10~max85mm

+90°

-45°

±90°

±180° ±180°

Components

Hardware

PACKAGE CONTENTS

M4x12mm (x4)

M-A

Screws

M4x16mm (x4)

M-B

Screws

M6x12mm (x4)

M-C

Screws

M6x16mm (x4)

M-D

Screws

D6 (x4)

M-E

Washer

5mm(x4)

M-F

Spacer

A (x1)

Arm

C (x1)

Bracket

D (x1)

Clamp

F (x1)

Long Bolt

G (x1)

Grommet Base

I (x1)

Security Screw

H (x1)

Support Plate

J (x6)

Screw

K(x1)

Wingnut

L(x1)

Base

M(x1)

Washer

N(x1)

Calathiform Gasket

O(x1)

Bolt

P(x1)

4mm Allen Key

Q(x1)

5mm Allen Key

E(x1)

Bracket Cover

B (x1)

VESA Plate

R(x1)

6mm Allen Key

STEP 1 Mount the Base to Bottom of the Arm

STEP 2 Clamp Installation OR Grommet Base Installation

OPTION A: Clamp Installation

Mount bracket (C) to the bottom of arm (A) using screws(J). Tighten the screws with

supplied 4mm Allen key (P).

Mount the base(L) to the bottom of arm (A) using Washer(M), calathiform gasket(N) and Bolt(O).

Tighten (do not over tighten) the Bolt (O) securely with supplied 5mm Allen key (Q).

concave side of the

washer needs to be

faced to the Base (L)

Secure clamp (D) to upper two holes with

bolts (J) using 4mm Allen Key (P) for desks

with a thickness of 10-55mm.

Secure clamp (D) to lower two holes with

bolts (J) using 4mm Allen Key (P) for desks

with a thickness of 50-85mm.

Adjust the Mount to the Desktop

Thickness 10-55mm

Adjust the Mount to the Desktop

Thickness 50-85mm

Attach bracket cover (E)to bracket(C). Tighten the clamp to the desktop using the plastic knob

or by using 6mm allen key (R).

10-55mm

50-85mm

STEP 2 (Continued)

OPTION B: Grommet Base Installation

For grommet hole mounting, place long bolt(F) through the center of grommet base (G).

Mount grommet base to the bottom of arm (A) using screws(J). Tighten the screws with

supplied 4mm Allen key (P).

Run long bolt(F) through grommet hole in desktop. Secure it by using the support plate (H)

and Wingnut (K). Tighten Wingnut.

STEP 3 Attach the monitor to the arm

OPTION A:Flat Back Monitor

Attach the VESA plate (B) to back of monitor and secure with

screws (M-A) or (M-C) with washers (M-E) using 6mm Allen

Key(R). Avoid excessive tightening screws damage the

monitor.

OPTION B:Curved Back Monitor

Attach the VESA plate (B) to back of monitor and secure

with screws (M-B) or ((M-D) with washers (M-E) and

spacers (M-F) using 6mm Allen Key(R). Avoid

excessive tightening screws damage the monitor.

M-A

M-C

M-E

M-B

M-D

M-E

M-F

Slide the monitor onto the head of swivel arm(A), install the security screw (I). Make

sure the security screw is installed before you rotate the monitor.

If the monitor sags or does not stay, please fasten the tilting bolt on the mount until the

monitor can be held at any angle as needed. Refer to below illustrations to adjust tilting

angle of your monitor.

Refer to below illustrations to

adjust tilting angle of your monitor.

Note: Fasten/loosen the tilting bolt

as needed per arrow direction (+/-)

shown in above diagram.

A A

STEP 4 Adjust the tension

For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust

tension spring in Arm (A) by using 6 mm Allen key (R).

Note:

It is normal for a bit noise when you adjust the spring tension.

After being attached to the arm, the monitor falls down

and can not stay at the desired height by itself.

Turn clockwise(“+”direction) to increase tension

until the monitor can stay at the desired Height by itself.

After being attached to the arm, the monitor rises up and

can not stay at the desired height by itself.

Turn counter-clockwise(“-”direction) to reduce tension until the

monitor can stay at the desired Height by itself.

WARNING

Please DO NOT loosen the screw.

STEP 5 Cable Management

Remove the bottom plastic covers from spring arm(A) as shown in diagram.

Run cables from monitor through the bottom of spring arm (A). Reattach plastic covers

as shown in diagram.

Inhaltsverzeichnis

Andere Mountup Rack & Stand Handbücher

Mountup

Mountup MU2001 Bedienungsanleitung

Mountup

Mountup MU0023 Bedienungsanleitung

Mountup

Mountup MU2005 Bedienungsanleitung

Mountup

Mountup MU0002 Bedienungsanleitung

Mountup

Mountup MU0011 Bedienungsanleitung

Mountup

Mountup MU5001 Bedienungsanleitung

Mountup

Mountup MU0021 Bedienungsanleitung

Mountup

Mountup MU0011 Bedienungsanleitung

Mountup

Mountup MU0060 Bedienungsanleitung

Mountup

Mountup MU2002 Bedienungsanleitung

Mountup

Mountup MU4001 Bedienungsanleitung

Mountup

Mountup MU7012 Bedienungsanleitung

Mountup

Mountup MU6003 Bedienungsanleitung

Mountup

Mountup MU5004 Bedienungsanleitung

Mountup

Mountup MU6001 Bedienungsanleitung

Mountup

Mountup MU0029 Bedienungsanleitung

Mountup

Mountup MU6002 Bedienungsanleitung

Mountup

Mountup MUA6008B Bedienungsanleitung

Mountup

Mountup MU9101B Bedienungsanleitung

Mountup

Mountup MU0014 Bedienungsanleitung

Mountup

Mountup MU0001 Bedienungsanleitung

Mountup

Mountup MU0022 Bedienungsanleitung

Mountup

Mountup MU0006 Bedienungsanleitung

Mountup

Mountup MU0024 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung