Moxa Technologies PWR-100 Series Bedienungsanleitung

P/N: 1802001003010

*1802001003010*

PWR-100 Power Module Series

Quick Installation Guide

Power Modules for EDS-4000/G4000 Series

Version 1.0, July 2023

Technical Support Contact Information

www.moxa.com/support



- 2 -

Package Checklist

The PWR-100 Series power module is shipped with the following items.

If any of these items are missing or damaged, please contact your

customer service representative for assistance.

•1 PWR-100 Series power module

•Quick installation guide (printed)

•Warranty card

•Substance disclosure table

•Product certificate of quality inspection (Simplified Chinese)

•Product notices (Simplified Chinese)

NOTE

You can find information on the relevant product pages located

on Moxa’s website: www.moxa.com

Wiring Requirements

ATTENTION

Safety First!

External metal parts are hot. Take

the necessary precautions if

you are required to handle the device.

ATTENTION

In order to ensure reliable operations, please make sure the

operating temperature of the environment does not exceed the

specifications. When mounting an EDS device with other

operating units in a cabinet without forced ventilation, a

minimum of

4 cm spac

e on both the left and right of the switch

is recommended.

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your EDS device. Calculate the maximum possible

current in each

power wire and common wire. Observe all

electrical codes dictating the maximum current allowable for

each wire size. If the current goes above the maximum ratings,

the wiring could overheat, causing serious damage to your

equipment.

Be sure to read and follow these important points below:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

- 3 -

NOTE

Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires

with different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring that shares similar electrical characteristics can be

bundled together.

•You should separate input wiring from output wiring.

•We advise that you label the wiring to all devices in your system.

Suggested Wire Type for Wiring Relay Contact

(RELAY), Digital Input (DI), and Power Inputs

(P1/P2)

The PWR-100 Series power module has two 4-pins 3.5 mm pin-pitch

terminal blocks. When wiring the relay contact (RELAY), digital input

(DI), and power inputs (P1/P2), we suggest using the cable type AWG

18-24 and the corresponding pin type cable terminals.

NOTE

The wire must be

able to withstand at least 105°C and the

torque value should be 4.5 lb-in (0.51 N-m).

NOTE

We suggest the length of the pin type cable terminal is 8

mm.

In order to tighten the wire properly,

①use a small flathead

screwdriver to press the push

in button beside each terminal of

the terminal block connector before and during

②

inserting the

wire.

③Release the screwdriver after the wire has been fully

nserted. Please refer to the diagram below.

Wiring the Relay Contact

The PWR-100 Series power module has one set of relay outputs. This

relay contact uses two contacts of the terminal block on the power

module. Refer to the section for detailed instructions on how to connect

the wires to the terminal block connector, and how to attach the

terminal block connector to the terminal block receptor.

- 4 -

Relay:

The two contacts of

the 4-pin terminal

block connector are used to detect

user

-configured events. The two wires

attached to the

fault contacts form an

open circui

t when a user-configured

event is triggered or

there is no power

supply to the switch

. If a user-

configured event does not occur, the

fault circuit remains closed.

Wiring the Redundant Power Inputs

The PWR-100 Series includes both high-voltage and low-voltage

models. For the low-voltage (LV models) products, there are two power

inputs for redundancy; for the high-voltage (HV models) products,

there is only one power input. Refer to the instructions and diagram

below on how to connect the wires to the terminal block connector on

the receptor.

STEP 1:

Insert the Positive/Negative

DC or Line/Neutral AC wires into the

V+/V

- or L/N terminals, respectively.

STEP 2:

To keep the DC or AC wires

from pulling loose, use a small flat

blade screwdriver to tighten the wire

clamp screws on the front of the

terminal block connector.

STEP 3:

Insert the plastic terminal

block connector prongs into the

- 5 -

terminal block receptor, which is

located on the EDS devices’ right side.

Wiring the Digital Inputs

The PWR-100 Series power module has one set of digital inputs (DI).

The DI consists of two contacts of the 4-pin terminal block connector on

the EDS's right-side panel. Refer to the instructions and diagram below

on how to connect the wires to the terminal block connector on the

receptor.

STEP 1: Insert the negative

(ground)/positive DI wires into the

┴

/I terminals, respectively.

STEP 2:

To keep the DI wires from

pulling

loose, use a small flat-blade

screwdriver to tighten the wire

-clamp

button

on the front of the terminal

block connector.

STEP 3:

Insert the plastic terminal

block connector prongs into the

terminal block receptor, which is

located on the EDS devices’ right side.

Replacing or Rotating the Power Module

The power module for the EDS device can be replaced or rotated to fit

the requirements of your field site application.

Step 1:

Remove

the two screws that fasten the power module to the

EDS device

Step 2:

Remove the power module from the EDS device.

Step 3:

(Optional) Rotate the power module clockwise so that the

power, digital input, and relay output connectors are facing

upwards.

Step 4:

Place the module, or another module, back onto the EDS

device, then fasten the screws to secure the power module to

the device.

- 6 -

Specifications

Power

Note The EDS-4000/G4000 Series device model name

and power parameters are determined by the

installed PWR-100 power module.

PWR-100–LV: -LV/-LV-T models

PWR-105-HV-I: -HV/-HV-T models

PWR-101-LV-BP-I: -LVA/-LVA-T models (PoE

support)

PWR-103-LV-VB-I: -LVB/-LVB-T models (PoE

support)

For example:

EDS-G4008-T + PWR-100-LV = EDS-G4008-LV-T

EDS-G4008-T + PWR-105-HV-I = EDS-G4008-HV-

If you install a different power module, refer to the

specifications of the corresponding model. For

example, if you replace the power module of the

EDS-G4008-LV-T with the PWR-105-HV-I, refer to

the specifications of the EDS-G4008-HV-T.

Rated Voltage

PWR-100-LV: 12/24/48 VDC, redundant dual

inputs

PWR-105-LV-I: 110/220 VDC, single input

PWR-101-LV-BP-I: 48 VDC, redundant dual inputs

PWR-103-LV-VB-I: 12/24/48 VDC, redundant dual

inputs

Operating Voltage

PWR-100-LV: 9.6 to 60 VDC

PWR-105-HV-I: 88 to 300 VDC, 85 to 264 VAC

PWR-101-LV-BP-I: 44 to 57 VDC (> 52 VDC for

PoE+ output recommended)

PWR-103-LV-VB-I: 12 to 57 VDC (>52 VDC for

PoE+ output recommended)

Rated Current

PWR-100-LV: 12 to 48 VDC, 1.50 to 0.40 A or 24

VDC, 0.70 A

PWR-105-HV-I: 110 to 220 VAC, 50 to 60 Hz, 0.30

to 0.20 A or 110 to 220 VDC, 0.30 to 0.20 A

PWR-101-LV-BP-I: 48 VDC, 5.42 A

PWR-103-LV-VB-I: 12/48 VDC, 7.46/4.27 A or

24 VDC, 7.26 A

Inrush Current

-LV models: Max. 0.8 A @ 48 VDC (0.1 to 1 ms)

Power over

Ethernet

Only the EDS-4008-4P-2GT-2GS(-T), EDS-4012-

8P-4GS(-T), and EDS-G4012-8P-4QGS(-T) models

- 7 -

support PoE. If a PoE-capable PWR-100 Series

module (PWR-101-LV-BP-I, PWR-103-LV-VB-I) is

installed into an EDS-4000/G4000 Series non-PoE

model, PoE functionality will not be available.

Overload Current

Protection at Input

Present

Reverse Polarity

Protection

Present

Connection

2 removable 4-contact terminal blocks

Physical Characteristics

Dimension

PWR-100-LV: 103 x 98 x 26.6 mm (4.06 x 3.86 x

1.02 in)

PWR-105-HV-I: 103 x 98 x 39.9 mm

(4.06 x 3.86 x

1.57 in)

PWR-101-LV-BP-I: 103 x 98 x 39.9 mm (4.06 x

3.86 x 1.57 in)

PWR-103-LV-VB-I: 103 x 98 x 39.9 mm (4.06 x

3.86 x 1.57 in)

Weight

PWR-100-LV: 142 g (0.31 lb)

PWR-105-HV-I: 215 g (0.47 lb)

PWR-101-LV-BP-I: 176 g (0.39 lb)

PWR-103-LV-VB-I: 244 g (0.54 lb)

Environmental Limits

Operating

Temperature

-10 to 60°C (14 to 140°F) for standard models

-40 to 75°C (-40 to 167°F) for -T models

Storage

Temperature

-40 to 85°C (-40 to 185°F)

Ambient Relative

Humidity

5 to 95% (non-condensing)

Altitude

Up to 2000 m

Note: Please contact Moxa if you require products

guaranteed to function properly at higher altitude.

Regulatory Approvals

Safety

EN 62368-1(LVD)

EMC

EN 55032/35, EN 61000-6-2/6-4

EMI

FCC Part 15 Subpart B Class A

EMS

EN 61000-4-2 (ESD) Level 4

EN 61000-4-3 (RS) Level 3

EN 61000-4-4 (EFT) Level 4

EN 61000-4-5 (Surge) Level 4

EN 61000-4-6 (CS) Level 3

EN 61000-4-8 Level 4

Package Drop &

Vibration

ISTA 1A

Warranty

5 years

- 8 -

ATTENTION

This device complies with Part 15 of the FCC rules.

Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received

including interference that may cause undesired operation.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Steuereinheit Handbücher

Moxa Technologies

Moxa Technologies MiiNePort E2-H Bedienungsanleitung

Moxa Technologies

Moxa Technologies WFS001 Bedienungsanleitung

Moxa Technologies

Moxa Technologies AWK-3252A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CA Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MiiNePort W1 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MiiNePort W1 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioThinx 4500 45ML-5401 Bedienungsanleitung

Moxa Technologies

Moxa Technologies WAPN005 Bedienungsanleitung

Moxa Technologies

Moxa Technologies WE-2100T Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CB-108 Bedienungsanleitung

Moxa Technologies

Moxa Technologies CA-134I Bedienungsanleitung

Moxa Technologies

Moxa Technologies CA-132 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioMirror E3200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MiiNePort W1 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PWR-190-AC/DC Bedienungsanleitung

Moxa Technologies

Moxa Technologies MiiNePort W1 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies WAPA003 Bedienungsanleitung

Moxa Technologies

Moxa Technologies WAPN008 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EOM-G103-PHR-PTP Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 4101-MB-PBS Bedienungsanleitung

Moxa Technologies

Moxa Technologies EOM-104 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ABC-01 Bedienungsanleitung

Moxa Technologies

Moxa Technologies CA Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung