Moxa Technologies AIG-300 Series Bedienungsanleitung

P/N: 1802003015012

*1802003015012*

AIG-300 Series

Quick Installation Guide

Advanced IIoT Gateways with Arm® Cortex™-A7 dual-core 1

GHz processor, 1 CAN port, 4 DIs, 4 DOs, ThingsPro Edge

software, -40 to 70°C operating temperature

Version 1.2, December 2021

Technical Support Contact Information

www.moxa.com/support

- 2 -

Package Checklist

Before installing the device, verify that the package contains the

following items:

•AIG-300 Series advanced IIoT gateway

•Power jack

•DIN-rail mounting kit

•Quick installation guide (printed)

•Warranty card

IMPORTANT!

The console cable is not included in the package; you need to

purchase it separately. Notify your sales representative if any of

the above items are missing or damaged.

Panel Views

The following figures show the panel layouts of the AIG-300 Series:

AIG-301-T-AZU-LX

Top Panel

- 3 -

Front Panel

Bottom Panel

AIG-301 US, EU, AP, and CN Models

NOTE

The CN model does not come

preinstalled

with the LTE module.

Contact Moxa’s distributor in China for more information.

Top Panel

- 4 -

Front Panel

Bottom Panel View

LED Indicators

LED Name

Status

Function

PWR1/PWR2

Green

Power is on

Off

No power is supplied

SIM

Green

SIM2 in use

Yellow

SIM1 in use

USR Green/Yellow

Green: System is operating normally

Yellow: System is initializing and running

the initial boot-up process

L1/L2/L3 Yellow

Cellular signal strength

L1+L2+L3: Strong

L2+L3: Normal

L3:Weak

W1/W2/W3

Yellow

WLAN signal strength

W1+W2+W3: Strong

W2+W3: Normal

W3: Weak

LAN1/LAN2

(RJ45

connector)

Green

Steady on

1000 Mbps Ethernet link

Blinking

Data is being transmitted

Yellow

Steady on

100 Mbps Ethernet link

Blinking

Data is being transmitted

Off

No Ethernet connection or 10 Mbps

Ethernet link

- 5 -

Mounting Instructions

DIN-rail Mounting

The aluminum DIN-rail attachment plate is already attached to the

product’s casing. To mount the device on to a DIN rail, make sure that

the stiff metal spring is facing upwards and follow these steps.

Pull down the bottom slider of

the DIN-rail bracket located at

the back of the unit

Insert the top of the DIN rail

into the slot just below the

upper hook of the DIN-rail

bracket.

Latch the unit firmly on to the

DIN rail as shown in the

illustrations below.

Push the slider back into place.

Wall Mounting (optional)

The device can be mounted on to a wall using a wall-mounting kit. The

optional wall-mounting kit should be purchased separately.

Follow these steps to mount the device on to a wall:

Step 1

Use four screws to fasten the wall

mounting brackets on the left panel

of the device.

Step 2

Use another four screws to mount

the

device on to a wall or in a

cabinet.

- 6 -

IMPORTANT!

The diameter of the screw heads

should be greater than 7 mm

and less than 14 mm; the diameter of the shafts should be less

than 3 mm. The length of the screws should be greater than 6

mm.

NOTE

•Test the screw head and shank size by inserting the screws

into one of the keyhole shaped apertures of the wall-

mounting plates before attaching the plate to the wall.

•

Do not drive the screws in all the way—leave a space of

about 2 mm to allow room for sliding the wall mount panel

between the wall and the screws.

Wiring Requirements

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separate.

•When necessary, it is strongly advised that you label wiring to all

devices in the system.

NOTE

Do not run signal or communication wiring and power wiring in

the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

Grounding Requirements

There is a grounding connector located on the top panel of the device.

Connect it to an appropriate grounded metal surface. Grounding and

wire routing help limit the effects of noise due to electromagnetic

interference (EMI).

Connecting the Power Supply

onnect the power jack (in the package)

the DC terminal block (located on the

top

panel), and then connect the power

adapt

er. It takes about 3 minutes for the

system to boot up. Once the system is

ready, the

Power LED will light up. Both

odels support dual power inputs for

redundancy.

Use wires with 12 to 26 AWG wire size to connect to V+, V-, and GND.

- 7 -

The wire size of the power input and the earthing conductor should be

the same. Remove 8 to 9 mm of the DC wires’ protective cover and use

a torque of 4.5lb-in/0.51Nm to connect the wire. The max. wire

temperature should not exceed 100°C. The terminal blocks do not

accommodate more than one conductor wire per clamping point.

WARNING

EXPLOSION HAZARD!

Do not disconnect equipment unless the power has been

removed or the area is known to be non-hazardous.

WARNING

•

This product is intended to be supplied by a UL Listed

power adapter or DC power source whose output meets

SELV/LPS. The power source must be rated 12 to 48 VDC,

minimum 1 A, and minimum TMA = 85°C.

•

The power adapter should be connected to a socket outlet

with an earthing connection.

If you need further

information or assistance, contact a Moxa

representative.

Wiring the I/Os

There are four digital inputs and four digital

outputs on the top panel. Refer to the figure

on the left for detailed pin definitions.

Use wires with 16 to 28 AWG wire size

connect to DI, DO, and GND.

The

exposed conductor wire

length should be

-8 mm and the max. wire temperature

should not exceed 100°C. The terminal blocks

do not accommodate more than one

conductor wire per clamping point.

DI Dry Contact

DO Channel (Sink Type)

- 8 -

Communication Connections

Connecting to the Network

The two 10/100/1000 Mbps Ethernet ports (LAN 1 and LAN 2) use RJ45

connectors. Refer to the figure to the

10/100 Mbps

1000 Mbps

Tx+

TRD(0)+

Tx-

TRD(0)-

Rx+

TRD(1)+

–

TRD(2)+

–

TRD(2)-

Rx-

TRD(1)-

–

TRD(3)+

–

TRD(3)-

Connecting to Serial Ports

The two serial ports (P1 and P2) use DB9 interface. Each port can be

configured by software for RS-232, RS-422, or RS-485. The pin

assignments for the ports are shown in the following table:

Pin RS-232

RS-422/

RS-485 4w

RS-485 2w

–

TxD-(A)

–

RxD

TxD+(B)

–

TxD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

Inserting the microSD Card

The device comes with a micro-SD slot for storage expansion. The

microSD slot is located at the lower part on the front panel. To install

the card, remove the screw and the protection cover to access the slot

and insert the microSD card into the slot.

You will hear a click when the card is in place. To remove the card,

push the card in before releasing it.

Connecting to the Console Port

The console port is an RS-232 port located on the top panel, and can be

connected to a 4-pin pin header cable. You can use this port for

debugging or firmware upgrade.

- 9 -

Signal

TxD

RxD

GND

Connecting a USB Device

The device comes with a USB port located on the lower part of the front

panel, allowing users to connect to a device with an USB interface. The

USB port uses a type-A connector.

Connecting a CAN Device

A CAN port with a DB9 interface is located on the bottom panel. Refer

to the figure below for detailed pin definitions.

Definition

–

CAN_L

CAN_GND

–

(CAN_SHLD)

(GND)

CAN_H

–

(CAN_V+)

Inserting a SIM Card

The device comes with two SIM card slots to install up to two SIM cards

for cellular communication.

Step 1

Remove the screw on the SIM card

holder

cover located on the bottom

panel of the

device.

Step 2

Insert the SIM card into the

socket. Make sure you insert

it in

the right direction. To remove the

SIM card, press the SIM card in to

release and then pull out the SIM

card.

Connecting the Antennas

There are two cellular antenna

connectors (C1 and C2) on the front

panel of the device. In addition, a

GPS connector is provided for the

GPS module. All three are SMA type

connectors. Connect the antennas to

these connectors as indicated.

- 10 -

The device also comes with two Wi-Fi

antenna connectors (W1 and W2) on

the top panel of the device. Connect

the antennas on the connectors as

shown below. Both W1 and W2

connectors are of RP

-SMA type.

NOTE

The optional Wi-Fi wireless module is not included in the

product package and must be purchased separately. Refer to

the AIG

-300 Series hardware manual, which can be

downloaded from

https://www.moxa.com, to install the Wi-Fi

module for the device.

Connecting the Device to a PC

You can use a PC to access the AIG-300 Series by one of the following

methods:

A. Access the web console of ThingsPro Edge via LAN 2 by

https://192.168.4.127:8443/.

Default Username : admin

Password: admin@123.

B. Using SSH over the network.

Refer to the following IP addresses and login information:

Default IP Address

Netmask

LAN 1

DHCP

LAN 2

192.168.4.127

255.255.255.0

Password: moxa

NOTE

For security reasons the SSH port is disabled by default. You

can enable it via the ThingsPro Edge web console.

Troubleshooting

Reboot

To reboot the device, press the Function (FN) button for 1 second.

Reset to Default

Press and hold the Function (FN) button between 7 to 9 seconds to

reset the device to the factory default settings. When the reset button

is held down, the USR LED will blink once every second and become

steady after 7 to 9 seconds. Release the button within this period to

load the factory default settings.

Real-time Clock

The real-time clock is powered by a lithium battery. We strongly

recommend that you do not replace the lithium battery without the help

Andere Handbücher für AIG-300 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Industrie-PC Handbücher

Moxa Technologies

Moxa Technologies UC-7400-LX Plus Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-685 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TC-6110-W7E Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-2200A Series Gebrauchsanweisung

Moxa Technologies

Moxa Technologies UC-3100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik 2500 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IA260 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies V481-XPE Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-710 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies V460 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies THINKCORE W345 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-7122 Gebrauchsanweisung

Moxa Technologies

Moxa Technologies DA-662A-8 Gebrauchsanweisung

Moxa Technologies

Moxa Technologies AWK-4252A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8100A-ME-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies IA260 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E2200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies V2616A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IA241-LX Bedienungsanleitung

Moxa Technologies

Moxa Technologies IA240-LX Bedienungsanleitung

Moxa Technologies

Moxa Technologies IA240 Gebrauchsanweisung

Moxa Technologies

Moxa Technologies UC-8100 Series Gebrauchsanweisung

Moxa Technologies

Moxa Technologies UC-8112-LX STK Bedienungsanleitung

Moxa Technologies

Moxa Technologies BXP-C100 Series Gebrauchsanweisung

Beliebte Industrie-PC Handbücher anderer Marken

Chipsee

Chipsee PPC-A72-101 Bedienungsanleitung

Advantech

Advantech UNO-2184G Bedienungsanleitung

MSI

MSI MS-9A76 Bedienungsanleitung

Stackrack

Stackrack THOR200 Bedienungsanleitung

Nodka

Nodka eBOX-3000-ETC Bedienungsanleitung

Siemens

Siemens SIMATIC IPC627E Bedienungsanleitung

Artila

Artila Matrix-516 Bedienungsanleitung

MSI

MSI MS-9A89 Bedienungsanleitung

Siemens

Siemens SIMATIC Rack PC 840 V2 Bedienungsanleitung

Advantech

Advantech IPPC-6152A Bedienungsanleitung

Beckhoff

Beckhoff CX9020 Bedienungsanleitung

Dell

Dell Embedded Box PC 5000 Bedienungsanleitung

IBASE Technology

IBASE Technology ASB200-918 Series Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M90q Betriebsanleitung

IXXAT

IXXAT Econ 100 Bedienungsanleitung

Kontron

Kontron KBox A-151-TGL Bedienungsanleitung

AXIOMTEK

AXIOMTEK ICO500-518 Series Bedienungsanleitung

JLT

JLT 1214N Bedienungsanleitung