Moxa Technologies Airworks AWK-3131A-M12-RCC Bedienungsanleitung

P/N: 1802031312031

*1802031312031*

AWK-3131A-M12-RCC

Quick Installation Guide

Moxa AirWorks

Edition 2.0, January 2019

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

ll-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

Moxa’s new AWK-3131A-M12-RCC is a 3-in-1 industrial AP/client device

designed specifically for rail carriage-to-carriage communication and can

provide up to 300 Mbps speed with IEEE 802.11n technology. The

AWK-3131A-M12-RCC combines two adjacent 20 MHz channels into a

single 40 MHz channel to deliver a potent combination of greater

reliability and more bandwidth. The dual DC power inputs increase the

reliability of the power supply, and the AWK-3131A-M12-RCC can be

powered via PoE to make deployment easier. The AWK-3131A-M12-RCC

can operate on either the 2.4 or 5 GHz bands and is backward-compatible

with existing 802.11a/b/g deployments to future-proof your wireless

investments.

Package Checklist

•AWK-3131A-M12-RCC

•Cable holder with one screw

•2 plastic RJ45 protective caps for Console port

•DIN-rail kit (preinstalled)

•Quick installation guide (printed)

•Warranty card

If any of these items is missing or damaged, please contact your

customer service representative for assistance.

NOTE

Antennas are not included and should be purchased separately.

The AWK is certified with 2

dBi omni-directional antennas with

QMA to RP-SMA adapters.

Installation and Configuration

Before installing the AWK-3131A-M12-RCC, make sure that all items in

the Package Checklist are in the box. In addition, you will need access to

a notebook computer or PC equipped with an Ethernet port. The

AWK-3131A-M12-RCC has a default IP address that you must use when

connecting to the device for the first time.

Step 1: Select the power source

The AWK-3131A-M12-RCC can be powered by a DC power input or PoE

(Power over Ethernet). The AWK-3131A-M12-RCC will use whichever

power source you choose.

Step 2: Connect the AWK-3131A-M12-RCC to a notebook

or PC

Since the AWK-3131A-M12-RCC supports MDI/MDI-X auto-sensing, you

can use either a straight-through cable or crossover cable to connect the

AWK-3131A-M12-RCC to a computer. If the LAN LED indicator on the

AWK-3131A-M12-RCC port lights up, it means the connection is

established.

- 3 -

Step 3: Set up the computer’s IP address

Set an IP address on the same subnet as the AWK-3131A-M12-RCC.

Since the AWK-3131A-M12-RCC’s default IP address is 192.168.127.253,

and the subnet mask is 255.255.255.0, you should set the IP address of

the computer to 192.168.127.xxx and subnet mask to 255.255.255.0.

Step 4: Use the web-based manager to configure

AWK-3131A-M12-RCC

Open your computer’s web browser and then type

http://192.168.127.253 in the address field to access the homepage

of the web-based management. Before the homepage opens, you will

need to enter the user name and password. For first-time configuration,

enter the default user name and password and then click on the Login

button:

Username: admin

Password: moxa

ATTENTION

For security reasons, we strongly recommend changing the

password. To do so,

select Maintenance



Password

, and then

follow the on-screen instructions.

Step 5: Select the operation mode for the

AWK-3131A-M12-RCC

By default, the AWK-3131A-M12-RCC’s operation mode is set to AP. You

can change the setting in Wireless Settings Basic Wireless

Settings if you would like to use the Client mode.

NOTE

To make the change effective, you must click Save Configuration

to save the cha

nge or the Save and Restart button to apply all

changes.

- 4 -

Panel Layout of the AWK-3131A-M12-RCC

1. Grounding screw (M5)

2. Terminal block for PWR1, PWR2,

relay, DI0, and DI1

3. Reset button

4. A antenna connector

5. B antenna connector

6. System LEDs: PWR1, PWR2, PoE,

FAULT, and STATE

7. Signal strength indicator

8. CLIENT, WLAN, and LAN LEDs

9. RS-232 console port

10.

M12 LAN Port:

10/100/1000BaseT(X)

11.

Model name

12.

Screw holes for wall mounting kit

13.

DIN-rail mounting kit

- 5 -

Mounting Dimensions (unit = mm)

DIN-rail Mounting

The aluminum DIN-rail attachment plate should be fixed to the back panel

of the AWK-3131A-M12-RCC when you take it out of the box. If you need

to reattach the DIN-rail attachment plate to the AWK-3131A-M12-RCC,

make sure the stiff metal spring is situated towards the top, as shown in

the figures below.

STEP 1:

Insert the top of the DIN

rail into

the slot just

below the stiff metal

spring.

STEP 2:

The DIN

-rail attachment unit will

snap into place as shown below.

To remove the AWK-3131A-M12-RCC from the DIN rail, simply reverse

Steps 1 and 2.

- 6 -

Wall Mounting (optional)

For transportation applications that require an EN 50155 certification

report, we strongly recommend the purchase of the optional

AWK-3131A-M12-RCC wall-mounting kit, which has passed EN 50155

testing. This wall-mounting kit is also convenient for other applications

that require mounting the AWK-3131A-M12-RCC to a wall.

STEP 1:

Remove the aluminum

DIN

-rail attachment plate

from the

AWK

-3131A-M12-RCC, and

then attach the wall mount

plates with M3 sc

rews, as

shown in the adjacent

diagrams.

STEP 2:

Mounting the

AWK-3131A-M12-

RCC to a wall requires

screws. Use the AWK-3131A-M12-

RCC device, with

wall mount plates attached, as a guide to mark the

correct locations of the

4 screws. The heads of the

rews should be less than 6.0 mm in diameter, and

the

shafts should be less than 3.5 mm in diameter, as

shown in the figure at the right.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the wall mount panel between the wall and the

screws.

NOTE

Test the screw head and shank size by inserting the screw into

one of the keyhole shaped apertures of the Wall Mounting Plates

before it is screwed into the wall.

STEP 3:

Once the screws are fixed into

the wall, inse

rt the four screw

heads through the large opening

of the keyhole

-shaped

apertures, and then slide the

AWK

-3131A-M12-RCC

downwards, as indicated to the

right. Tighten the three screws

for added stability.

- 7 -

WARNING

•

is equipment is intended to be used in a Restricted Access

Location, such as a

dedicated computer room, a cabinet, or

space specially reserved for device installation onboard a

train. Access can only be gained by SERVICE PERSONS

or by

USERS who have been instructed to comply with the

safety

rules thereby

avoiding casualties from electric shock, cutting

from a sharp edge, heat from a metallic surface, and so on.

•

Service persons or users have to pay special attention and

take special precautions before handling equipment.

•

Access is to be controlled through the use of a lock and key or

a security identity system, controlled by the authority

responsible for the location. Only authorized, well-trained

professionals are allowed to access the restricted access

location.

•

The metallic surface of the product may be hot when it is

installed in cabinets, places with direct sunlight, or next to a

high heat source. Pay special attention or use special

protection before handling equipment.

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa AWK-3131A-M12-RCC.

WARNING

Safety First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowed for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring with similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the system

when necessary.

- 8 -

ATTENTION

his product is intended to be supplied by a Listed Power Unit

marked

“Class 2” or “LPS” and rated O/P: 12 to 48 VDC

, minimum

6 W (12 V to 48V), 25°C.

ATTENTION

Make sure

the external power adapter (includes power cords an

plug assemblies) provided with the unit is certified and suitable

for use in your country.

ATTENTION

Do not use the PoE Injector. Instead, please use an IEEE802.3af

or IEEE802.3at compliant PSE (Power Sourcing Equipment

) for

PoE (Power over Ethernet) device.

Grounding the Moxa AWK-3131A-M12-RCC

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface, such as a metal panel.

Connecting the Power Input

Pinouts for the Power Inputs and Relay Output

Name

Usage

V1+

DC Power Input 1

V1-

V2+

DC Power Input 2

V2-

Relay Output

Digital Input

COM_1

Digital Input GND

Digital Input

COM_2

Digital Input GND

- 9 -

Wiring the Dual Power Inputs

The top two pairs of contacts of the 10-contact terminal block connector

on the AWK-3131A-M12-RCC’s top panel are used for the

AWK-3131A-M12-RCC’s two DC inputs. Top and front views of the

terminal block connector are shown below.

STEP 1:

Insert the negative/positive DC wires into the

-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose, use a

small flat

-blade screwdriver to tighten the

wire

-clamp screws on the front of the terminal

block connector.

STEP 3:

Insert the plastic terminal block connector

prongs into the terminal

block receptor, which is

located on

the AWK-3131A-M12-RCC’s top

panel.

NOTE

Before connecting the AWK

-3131A-M12-RCC to the DC power

inputs, make sure the DC power source voltage is stable.

Wiring the Relay Contact

The AWK-3131A-M12-RCC has one relay output, which consists of the

two contacts of the terminal block on the AWK-3131A-M12-RCC’s top

panel. The two wires attached to the Relay contacts form an open circuit

when a user-configured event, such as the network connection status

change, DI0/1 status change, or power status change, is triggered. If a

user-configured event does not occur, the Relay circuit will be closed.

Wiring the Digital Inputs

The AWK-3131A-M12-RCC has two sets of digital input—DI0 and DI1.

Each DI comprises two contacts of the 10-pin terminal block connector on

the AWK-3131A-M12-RCC’s top panel.

Cable Holder Installation

You can attach the cable holder to the bottom of the

AWK-3131A-M12-RCC. This helps to keep cabling neat and avoid

accidents that result from untidy cables.

- 10 -

STEP 1:

Screw the cable holder onto the bottom of the

AWK

-3131A-M12-RCC.

STEP 2:

After mounting the AWK-3131A-M12-RCC and plugging in the

LAN cable, tighten the cable along the device and wall.

Communication Connections

10/100/1000BaseT(X) Ethernet Port Connection

All AWK-3131A-M12-RCCs have a 10/100/1000BaseT(X) Ethernet port

(8-pin shielded M12 connector with A coding). The 10/100/1000TX port

located on the AWK-3131A-M12-RCC front panel is used to connect to

Ethernet-enabled devices. Most users configure this port for Auto

MDI/MDI-X mode, in which case the port’s pinouts are adjusted

automatically depending on the type of Ethernet cable used

(straight-through or cross-over), and the type of device (NIC-type or

HUB/Switch-type) connected to the port.

Pinouts for the 10/100/1000BaseT(X) M12 (8-pin) Port

Andere Handbücher für Airworks AWK-3131A-M12-RCC

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Hardware Handbücher

Moxa Technologies

Moxa Technologies NPort 5110 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IA3341 Gebrauchsanweisung

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-660-LX Bedienungsanleitung

Moxa Technologies

Moxa Technologies TAP-125 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MRC-1002 Series Kurzanleitung

Moxa Technologies

Moxa Technologies airworks awk-5232 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EOM-G103-PHR-PTP Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MAR-2000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-8580 Series Gebrauchsanweisung

Moxa Technologies

Moxa Technologies AWK Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies AirWorks AWK-5222 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MiiNePort E3 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies RNAS-1200 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-7420/7410 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-661-CE Bedienungsanleitung

Moxa Technologies

Moxa Technologies V91 Guide Bedienungsanleitung

Moxa Technologies

Moxa Technologies EOM-G103-PHR-PTP Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TRC-2190 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5410 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioMirror E3210 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung