Moxa Technologies PT-G510 Series Bedienungsanleitung

P/N: 1802005103002

*1802005103002*

PT-G510 Series

Quick Installation Guide

Version 1.1, September 2023

Technical Support Contact Information

www.moxa.com/support



- 2 -

Package Checklist

Moxa’s PT-G510 industrial DIN-rail switch is shipped with the following

items. If any of these items are missing or damaged, please contact

your customer service representative for assistance.

•PT-G510 switch

•DIN-rail kit

•Protective caps on SFP ports and USB Storage ports

•RJ45 to DB9 Cable

•Quick installation guide (printed)

•Substance Disclosure Table

•Product Certificate of Quality Inspection (Simplified Chinese)

•Product Notices (Simplified Chinese)

•Warranty card

NOTE

You can find information and software downloads on the

relevant product pages located on Moxa’s website:

www.moxa.com/

Default Settings

•Default IP address: 192.168.127.253

•Default Subnet Mask: 255.255.255.0

•Default Usernames: admin, user

•Default Password: moxa

Panel Layouts

PT-G510-4GTX4GSFP-PHR Models

- 3 -

PT-G510-8GSFP-PHR Models

PT-G510-8GTX-PHR Models

- 4 -

Dimensions

DIN-rail Mounting Instructions

The DIN-rail mounting kit is fixed to the back panel of the PT-G510 by

default. Mount the PT-G510 on a corrosion free mounting rail that

meets the EN 60715 standard.

Installation

STEP 1:

Insert the upper lip of the

DIN

-rail into the DIN-rail

mounting kit.

STEP 2:

Press the PT

-G510 towards

the DIN

-rail until it snaps

into place.

- 5 -

Removal

STEP 1:

Pull down the latch on the

mounting kit with a

screwdriver.

STEP 2 & 3:

Slightly pull the PT

-G510

forward and lift to

remove it from the DIN

rail.

ATTENTION

Safety First

Be sure to disconnect the power cord before installing and/or

wiring your Ethernet Switch. Calculate the maximum

possible

current in each power wire and common wire. Observe all

electrical codes dictating the maximum current allowable for

each wire size. If the current goes above the maximum ratings,

the wiring could overheat,

which can cause serious damage to

your equipment.

WARNING

Use only a Laser Class 1 optical transceiver with this device.

- 6 -

Connecting the Power Inputs

The PT-G510 Series switches support various types of power supplies.

•WV models come with two 24 to 48 VDC power inputs.

•HV models come with two 110 to 220 VDC/VAC power inputs.

Refer to the table below for an overview of the power input connectors

on HV and WV models:

WV Models

HV Models

WARNING

This equipment is intended to be supplied by an external power

source (UL listed/ IEC 60950

-1/ IEC 62368-1) with output

rating 24 to 48 VDC, 1.1 A (minimum)

or 110 to 220 VDC,

0.3 A (minimum)

, and an ambient temperature of 75°C

(minimum).

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to be non

-hazardous. The

device may only be connected to the supply

voltage shown on

the type plate. The device is designed for operation with a

Safety Extra

-Low Voltage (SELV) or an isolated power supply,

which means that the

device may only be connected to the

supply voltage connections and to the signal contact with a

ELV or an isolated power supply in compliance with IEC

62368-1/EN 62368-1/UL 62368-1 or UL 61010.

Wiring the Redundant Power Inputs

The PT-G510 Series provides high-voltage (HV) and low-voltage (WV)

models with two power inputs for redundancy. Refer to the instructions

below on how to wire to the terminal block connectors.

- 7 -

ATTENTION

Before connecting the PT

-G510 Series to the AC or DC power

inputs, make sure the power source voltage is stable.

NOTE

If you intend to only use one power input, be sure to

disconnect the other power input (unplug the power cord or

disconnect the power input from the L and N contacts). Only

one power input LED will be on.

NOTE

When wiring the relay contact, we suggest using the cable type

– AWG (American Wire Gauge) 19-24.

For HV Models:

NOTE

For HV models with 220 VAC wires:

1. The AC voltages between each of the two wires from the

power supply source must be less than 264 VAC RMS. To

measure and ensure the AC voltage for the PWR1 and

PWR2 is within the correct range, please use a qualified

digital multi-meter (e.g., a Fluke 85V or equivalent)

before connecting and applying the power source to the

PT-G510 PWR1 and PWR2 input terminals. If the

difference in AC voltage exceeds 264 VAC RMS, an

isolation transformer (220 V to 110 V; minimum 50 VA)

must be used between the PT-G510 Series and the AC

power source to avoid damage from power surges.

2. Please use an isolation transformer (220 V to 110 V;

minimum 50 VA) between the PT-G510 Series and the

Uninterruptible Power Supply (UPS) source to avoid

damage from power surges. Please use a qualified digital

multi-meter to measure the AC power difference between

each pair of the four power cable wires to ensure that the

voltage difference between each pair of wires is less than

264 VAC RMS. You will need to measure the voltage

difference between 4 pairs of wires, as listed below: [L1-

N1], [L1-N2], [L1-L2] [N1-N2], [N1-L2], [N2-L2].

NOTE

If you intend to only use one power input, be sure to

disconnect the other power input (unplug the power cord or

disconnect the power input from the L and N contacts). Only

one power input LED will be on.

- 8 -

STEP 1: Insert the positive/negative DC or

ine/neutral AC wires into the V+/V- or L/N

terminals, respectively.

TEP 2: Use a flat-blade screwdriver to

tighten the wire

-clamps on the front of the

terminal block connector

to fasten the

wires

TEP 3: Insert the plastic terminal block

connector prongs into the

terminal block

receptor.

For WV Models:

STEP 1: Insert the positive/negative DC

wires into the V+/V

- terminals,

respectively.

TEP 2: Use a flat-blade screwdriver to

tighten the wire

-clamps on the front of the

terminal block

connector to fasten the

wires

TEP 3: Insert the plastic terminal block

connector prongs into the

terminal block

receptor.

Wiring the Relay Contact

Each power module has one relay output that can

provide two types of relay output. Refer to the

table

below for detailed information.

The relay contact is used to detect user

-configured

events. Two wires are attached to the relay pins with

normally close and normally open options.

FAULT:

The relay contact of the 3-pin terminal block connector is used to detect

user-configured events. The module provides normally open (NO) and

normally closed (NC) circuits depending on what the user chooses. For

pin definitions, refer to the table below.

Relay connection Power on state Event trigger

NO and COM

Closed circuit

Open circuit

NC and COM

Open circuit

Closed circuit

- 9 -

NOTE

When wiring the relay contact, we suggest using the cable type

AWG (American Wire Gauge) 16-24 (1.31-0.205 mm2) and

the corresponding pin type cable

terminals. The connector

must be able to withstand torque at maximum 5 pound

inches.

The rated temperature of wiring should be at least 105°C.

Grounding the Moxa Industrial DIN-rail Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from

the ground screw to the grounding surface prior to connecting devices.

Refer to table below for the location of the grounding screw.

HV Models

WV Models

NOTE

Using a shielded cable achieves better electromagnetic

resistance

. Use a green-

yellow grounding cable with a wire size

AWG 18 or higher to ground this product to earth.

RJ45 Console Connection

The PT-G510 has one RJ45 console port (RS-232) located on the front

panel. Use an RJ45-based cable to connect the PT-G510’s console port

to your PC’s COM port. You may then use a console terminal program,

such as Moxa PComm Lite - Serial Communication Tool for Windows, to

access the PT-G510 with a baudrate of 115200. Refer to the following

for the pin definition of the console port.

MDI Port Pinouts MDI-X Port Pinouts 8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

USB Storage Connection

The USB storage port is on the front panel of the PT-G510 switch and

comes with a type A connector (see the diagram below for pinout

assignments). Use Moxa’s ABC-02-USB automatic backup configurator

- 10 -

to connect to the PT-G510 USB storage port in order to perform

configuration backup, firmware upgrade, or system log file backup.

Description

VCC (+5V)

D- (Data-)

D+ (Data+)

GND (Ground)

The Reset Button

The reset button can perform two functions. One is to reset the PT-

G510 switch back to factory default settings and the other is to perform

a quick backup of configuration and log files to the ABC-02-USB

automatic backup configurator.

Reset to Factory Default Settings

Use a pointed object, such as a straightened paper clip or toothpick, to

depress the Reset button. When you do so, the STATE LED will start to

blink about once per second. Continue until the STATE LED begins

blinking more rapidly; this indicates that the button has been depressed

for five seconds and you can release the Reset button to load factory

default settings.

NOTE

DO NOT power off the switch when loading default settings.

Configuration and Log Files Backup

When the ABC-02-USB is connected to the PT-G510 switch, the reset

button allows for a quick back up of configuration and event logs to the

ABC-02-USB. Press the reset button to start backing up the current

system configuration files and event logs to the ABC-02-USB.

NOTE

When the ABC-02 is plugged in, you cannot reset to factory

default by pressing the reset button.

Andere Handbücher für PT-G510 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Hardware Handbücher

Moxa Technologies

Moxa Technologies NPort W2150A-W4 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-7110 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MAR-2000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort IA 5250 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies V91 Guide Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MiiNePort E3 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies AWK-6232-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Express DE-211 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TAP-125 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MRC-1002 Series Kurzanleitung

Moxa Technologies

Moxa Technologies AirWorks AWK-5222 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UC-7420/7410 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies DA-660-LX Bedienungsanleitung

Moxa Technologies

Moxa Technologies MXNVR-RO Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5410 Bedienungsanleitung

Moxa Technologies

Moxa Technologies AWK-3252A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies C320Turbo/PCIEL Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5610-8 Bedienungsanleitung

Moxa Technologies

Moxa Technologies airworks awk-5232 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EOM-G103-PHR-PTP Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Bedienungsanleitung

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung