Moxa Technologies ToughNet TN-5516 Series Handbuch

Moxa ToughNet Switch

TN-5516/5518 Series

Layer 2 M12 managed 16/16+2G-port Ethernet switches

Hardware Installation Guide

First Edition, October 2009

Reproduction without permission is prohibited.

P/N: 1802055160011

—1 —

Overview

The ToughNet TN-5516/5518 series M12 managed Ethernet switches are

designed for industrial applications in harsh environments. The TN series

switches use M12 and other circular connectors to ensure tight, robust

connections, and guarantee reliable operation against environmental

disturbances, such as vibration and shock. The wide selection of 12/24/36/48

VDC, 72/96/110 VDC, or 110/220 VDC/VAC dual redundant power supplies

increases the reliability of your communications. The TN-5516 switches

provide up to 16 fast Ethernet M12 ports.

The TN-5518 switches provide up to 16 fast Ethernet M12 ports, and the 2

ports located on the bottom provide a Gigabit Ethernet interface with bypass

relay option. Models with an extended operating temperature range of -40 to

75°C are also available. The TN-5516/5518 series Ethernet switches are

compliant with EN50155/50121-3-2/50121-4 (railway applications), NEMA

TS2 (traffic control systems), and e-Mark (vehicles) requirements, making

the switches suitable for a variety of industrial applications.

Package Checklist

Your ToughNet TN-5516/5518 switch is shipped with the following items. If

any of these items is missing or damaged, please contact your customer

service representative for assistance.

y1 Moxa ToughNet switch.

yHardware installation guide.

yCD-ROM with user’s manual, Windows utility, and SNMP MIB file.

yMoxa product warranty statement.

yM12 to DB9 console port cable.

y2 protective caps for console and relay output ports

yPanel mounting kit.

Features

Anti-Vibration Circular Connectors for Robust Links

yM12 D-coding 4 pins female connectors for Fast Ethernet 10/100BaseT(X)

ports.

yCircular connectors (RJ45-type) for Gigabit Ethernet

10/100/1000BaseT(X) ports

yM12 A-coding 5 pins male connectors for console and relay output.

yM23 5 pins male connector for power input.

Dual, Isolated Redundant Power Inputs

ySupports 12/24/36/48 VDC (8.4–60 VDC).

ySupports 72/110 VDC (50.4–54 VDC), isolated.

ySupports 110/220 VDC/VAC (88–300VDC, 85–264 VAC), isolated.

yDual redundant, parallel load-sharing power supplies.

High Performance Network Switching Technology

yIPv6 ready, certified by the IPv6 Logo Committee.

—2 —

yIEEE 1588 PTP (Precision Time Protocol) for the precise time

synchronization of networks.

yDHCP Option 82 for IP address assignment with different policies.

yModbus/TCP industrial Ethernet protocol.

yTurbo Ring, Turbo Chain,and RSTP/STP (IEEE802.1w/D).

yIGMP Snooping and GMRP for filtering multicast traffic from industrial

Ethernet protocols.

yPort-based VLAN, IEEE802.1Q VLAN, and GVRP protocol to ease

network planning.

yQoS (IEEE802.1p/1Q and TOS/DiffServ) to increase determinism.

y802.3ad, LACP for optimum bandwidth utilization.

yIEEE802.1X and https/SSL to enhance network security.

ySNMP v1/v2c/v3 for different levels of network management.

yRMON for efficient network monitoring and proactive capability.

yBandwidth management prevents unpredictable network status.

yLock port allows access by only authorized MAC addresses.

yPort mirroring for online debugging.

yAutomatic warning by exception through email, relay output.

yAutomatic recovery of connected devices’ IP addresses.

yLine-swap fast recovery.

yLLDP for automatic topology discovery through network management

software.

yConfigurable through Web browser, Telnet/Serial console, and Windows

utility.

Designed for Industry-specific Applications

yTwo Gigabit Ethernet ports to meet high bandwidth requirements.

yBypass relay option on the 2 Gigabit Ethernet ports ensure non-stop data

communication in the event the switch stops working due to a power

failure .

yThree rotary switches for setting the last 3 digits of the IP address makes

maintenance even easier.

yEN 50155/50121-3-2/50121-4, NEMA TS2, and e-Mark compliant.

y-40 to 75°C operating temperature range (for “-T” models).

yIP54/IP67, rugged high-strength case.

yPanel mounting or DIN-Rail mounting installation capability.

Recommended Optional Accessories

yCBL-M23(FF5P)Open-BK-100-IP67: 1-meter M23-to-5-pin power cable

with IP67-rated female 5-pin M23 connector.

yCBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UTP

Ethernet cable with IP67-rated male 4-pin M12 D-coded connector.

yCBL-M12(FF5P)/OPEN-100 IP67: 1-meter M12-to-5-pin power cable

with IP67-rated female 5-pin M12 A-coded connector.

yM12D-4P-IP68: Field-installable M12 D-coded screw-in connector, male

4-pin, IP68-rated.

—3 —

yM12A-5P-IP68: Field-installable M12 A-coded screw-in connector,

female 5-pin, IP68-rated.

yA-CAP-M12F-MIP67-PAK04: Caps for M12 D-coded 4-pin male

connectors, metal and IP67-rated. Four pieces in one pack.

yDK-DC50131: DIN-Rail mounting kit, 50 x 131 mm.

TN-5516 Panel Layouts

8 9 10 11 12

Top View

Front View

Botton View

Rear View

1. 3 Rotary switches and protective cover with Model name.

2. Screw holes for panel mounting kit.

3. Console port.

4. Grounding screw.

5. Relay output port.

6. Power input voltage range indication.

7. Power input port (male 5-pin shielded M23 connector).

8. PWR1 LED: for power input 1.

9. PWR2 LED: for power input 2.

—4 —

10. FAULT LED.

11. MSTR/HEAD LED: for ring master or chain head.

12. CPLR/TAIL LED: for ring coupler or chain tail.

13. TP port’s 10/100 Mbps LED.

14. 10/100BaseT(X) port (female 4-pin shielded M12 connector with D

coding).

15. Waterproof vent.

16. Product label.

17. 12 Screw holes for DIN-Rail mounting kit.

18. E1 LED: Not used by the TN-5516 series.

19. E2: LED: Not used by the TN-5516 series.

TN-5518 Panel Layouts

8 9 10 11 12

Top View

Front View

Botton View

Rear View

—5 —

1. 3 Rotary switches and protective cover with Model name.

2. Screw holes for panel mounting kit.

3. Console port.

4. Grounding screw.

5. Relay output port.

6. Power input voltage range indication.

7. Power input port (male 5-pin shielded M23 connector).

8. PWR1 LED: for power input 1.

9. PWR2 LED: for power input 2.

10. FAULT LED.

11. MSTR/HEAD LED: for ring master or chain head.

12. CPLR/TAIL LED: for ring coupler or chain tail.

13. TP port’s 10/100 Mbps LED.

14. 10/100BaseT(X) port (female 4-pin shielded M12 connector with D

coding).

15. Waterproof vent.

16. Product label.

17. 12 Screw holes for DIN-Rail mounting kit.

18. E1 LED: Down-side E1 Gigabit port's 10/100/1000 Mbps LED.

19. E2: LED: Down-side E2 Gigabit port's 10/100/1000 Mbps LED.

20. Gigabit Ethernet port E1 (corresponding to port 17 in the TN-5518

User's Manual).

21. Gigabit Ethernet port E2 (corresponding to port 18 in the TN-5518

User's Manual).

ATTENTION

DO NOT open or remove the vent (#15). Once the seal has

been removed, the warranty becomes invalid.

Exposed connectors (including 3, 5, and 14) when not in use

must be tightly covered with protective caps (an optional

accessory) to ensure IP54/IP67-rated protection.

After the rotary switches (1) are set, the protective cover must

be properly affixed to ensure IP54/IP67-rated protection.

—6 —

Mounting Dimensions (unit = mm)

TN-5516 Series

—7 —

TN-5518 Series

Panel/Wall Mounting

STEP 1:

Mounting the TN-5516/5518 to a wall requires 4 screws. Use the ToughNet

switch as a guide to mark the correct positions of the 4 screws.

STEP 2:

Use the 4 screws in the panel mounting kit. If you

would like to use your own screws, make sure the

screw head is between 6.0 mm and 7.0 mm in

diameter and the shaft is less than 4.0 mm in diameter,

as shown at the right.

Do not screw the screws in all the way—leave a space

of about 2 mm to allow room for sliding the ToughNet switch between the

wall and the screws.

NOTE Before tightening the screws into the wall, make sure the screw

head and shaft size are suitable by inserting the screw through one

of the keyhole-shaped apertures of the ToughNet switch.

6.0 - 7.0 mm

< 4.0 mm

—8 —

STEP 3:

Once the screws are fixed in the wall, hang the ToughNet switch on the 4

screws through the large opening of the keyhole-shaped apertures, and then

slide the switch downwards. Tighten the four screws for added stability.

NOTE To provide greater protection from vibrations and shocks, use

screws with shaft diameter between 6.0 mm and 7.0 mm, and fix

the ToughNet switch onto the wall directly through the large

opening of the keyhole-shaped apertures.

DIN-Rail Mounting (optional)

With the optional DIN-Rail

mounting kit DK-DC50131 (must

be purchased separately), you can

mount the TN-5516/5518 on a

35mm DIN-Rail.

STEP 1:

Use 12 screws (6 screws per plate)

to attach the two DIN-Rail

attachment plates to the rear panel

of the switch.

Recessed button

Spring-loaded bracket

STEP 2:

If the spring-loaded bracket is locked in place, push the recessed button to

release it. Once released, you should feel some resistance from the spring as

you slide the bracket up and down a few millimeters in each direction.

STEP 3:

Position the ToughNet switch on the

DIN-Rail, tilting to hook clamps over

the top edge of the rail.

STEP 4:

Swing the switch down fully onto

the DIN-Rail, until both clamps

completely latch.

DIN-Rail

—9 —

To remove the Moxa ToughNet Switch from the DIN-Rail, use a screwdriver

to pull out the two spring-loaded brackets from the bottom until they are fixed

in the “locked” position. Then reverse Step 3 and 4 above.

DIN-Rail

Wiring Requirements

WARNING

Turn the power off before disconnecting modules or wires. The

correct power supply voltage is listed on the product label. Check

the voltage of your power source to make sure you are using the

correct voltage. Do NOT use a voltage greater than what is

specified on the product label.

These devices must be supplied by a SELV source as defined in

the Low Voltage Directive 2006/95/EC and 2004/108/EC.

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa switch.

This device has UL508 approval. Use copper conductors only,

60/75°C, and tighten to 4.5 pound-inches. For use in pollution

degree 2 environments.

ATTENTION

Safety First!

Observe all electrical codes dictating the maximum current

allowable for each wire size. If the current goes above the

maximum ratings, the wiring could overheat, causing serious

damage to your equipment.

Andere Handbücher für ToughNet TN-5516 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Router Handbücher

Moxa Technologies

Moxa Technologies ioLogik E2200Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies E Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NAT-102 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7528 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ETHERDEVICE EDS-308 Handbuch

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-G9010 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Managed Ethernet Switch/Extender Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-G9010 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies SR3000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IKS-6324 Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Handbuch

Moxa Technologies

Moxa Technologies EDS-518E Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-G308 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-408A Handbuch

Moxa Technologies

Moxa Technologies ioLogik E1242 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Handbuch

Moxa Technologies

Moxa Technologies EDS-518E Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-810 Series Handbuch

Moxa Technologies

Moxa Technologies ToughNet TN-5308-4 Handbuch

Moxa Technologies

Moxa Technologies SDS-3008 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung