Moxa Technologies EDR-810 Series Handbuch

P/N: 1802008100011

Moxa Industrial Secure Router

Hardware Installation Guide

EDR-810 Series

Second Edition, May 2014

www.ipc2u.ru

www.moxa.pro

- 2 -

Package Checklist

The Moxa Industrial Secure Router is shipped with the following items. If

any of these items is missing or damaged, please contact your customer

service representative for assistance.

•1 Industrial Secure Router

•RJ45 to DB9 console port cable

•Protective caps for unused ports

•CD-ROM with User’s Manual and Windows utility

•Hardware Installation Guide

•Moxa product warranty statement

Features

Advanced Industrial Networking Capability

•Router/NAT/Firewall all in one

•Router with VRRP redundancy

•Firewall with Quick Automation Profile for rules of industrial protocols

•NAT with N-to-1, 1-to-1, and port-forwarding modes

•VPN for remote secure connection (VPN model only)

•Intelligent Policy Check for quick troubleshooting

•Support 1 WAN and up to 15 interfaces for LANs

•-40 to 75°C operating temperature (T model)

www.ipc2u.ru

www.moxa.pro

- 3 -

Panel Views of Industrial Secure Router

Front Panel:

1. USB port for ABC-02

2. 1000Mbps SFP port

3. 1000Mbps SFP port speed LED

indicator

4. Model name

5. Power input PWR1 LED indicator

6. Power input PWR2 LED indicator

7. STATE LED indicator

8. FAULT LED indicator

9. MSTR/HEAD LED indicator

10.

CPLR/TAIL LED indicator

11.

10/100Mbps copper port

12.

10/100Mbps copper port speed

LED indicator

Top Panel:

1. Grounding screw

Terminal block for power input 2

Terminal block for power input 1

4. Terminal block for relay output

5. Terminal block for digital input

6. RS-232 serial console port

7. RESET button

Rear Panel:

1. DIN-Rail mounting kit

2. Screw

holes for wall mounting kit

www.ipc2u.ru

www.moxa.pro

- 4 -

Mounting Dimensions (unit = mm)

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the

back panel of the Industrial Secure Router when you take it out of the box.

If you need to reattach the DIN-Rail attachment plate to the Industrial

Secure Router, make sure the stiff metal spring is situated towards the

top, as shown in the following figures.

STEP 1—Insert the top of the

DIN

-Rail into the slot just below

the stiff metal spring.

STEP 2—The DIN-Rail attachment

unit will snap into place as shown in

the following illustration.

To remove the Industrial Secure Router from the DIN-Rail, simply reverse

Steps 1 and 2 above.

Wall Mounting (Optional)

For some applications, you will find it convenient to mount Moxa EDR-810

on the wall, as shown in the following illustrations.

STEP 1—Remove the aluminum

DIN

-Rail attachment plate from

the rear panel of the EDR

810, and

then attach the wall mount plates

with M3 screws, as shown in the

figure at the r

ight.

www.ipc2u.ru

www.moxa.pro

- 5 -

STEP 2—Mounting the EDR-810 on the wall requires

four

screws. Use the EDR-810, with wall mount plates

attached, as a guide to mark the correct locations of

the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the shafts should be less

than 3.5 mm in diameter, as shown in the figure on the

right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the way—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

STEP 3—Once the screws are

fixed to the wall, insert the four

screw heads through the wide

parts of the keyhole

-shaped

apertures, and then slide the

EDR

-810 downwards, as

indicated in the figure at the

right. Tighten the four screws for

more stability.

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is

known to be non-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

Safety Extra

-Low Voltage. Thus, they may only be connected to

the supply voltage connections and to th

e signal contact with the

Safety Extra

-Low Voltages (SELV) in compliance with IEC950/

EN60950-1/ VDE0805.

ATTENTION

This unit is a built

-in type. When the unit is installed in another

piece of equipment, the equipment

enclosing the unit must

comply with fire enclosure regulation IEC 60950

-1/EN60950-1

(or similar regulation).

www.ipc2u.ru

www.moxa.pro

- 6 -

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa

Industrial Secure Router.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Please read and follow these guidelines:

Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

You can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring

sharing similar electrical characteristics can be bundled together

You should separate input wiring from output wiring

We advise that you label the wiring to all devices in the system.

Grounding the Moxa Industrial Secure Router

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface such as a metal panel.

www.ipc2u.ru

www.moxa.pro

- 7 -

Wiring the Relay Contact

The Industrial Secure Router has one set of relay outputs. This relay

contact uses one contacts of the terminal block on the Industrial Secure

Router’s top panel. Refer to the next section for detailed instructions on

how to connect the wires to the terminal block connector, and how to

attach the terminal block connector to the terminal block receptor.

In this section, we illustrate the meaning of the contact used to connect

the relay contact.

FAULT:

The two contacts of the 2

-pin terminal

block connector are used to detect

user

-configured events. The two wires

attached to the fault contacts form an

open circuit when a user

configured event

is triggered. If a user

-configured event

does not occur, the fault circuit remains

closed.

Wiring the Redundant Power Inputs

The Industrial Secure Router has two sets of power inputs—power input 1

and power input 2. The top and front views of one of the terminal block

connectors are shown here.

STEP 1: Insert the negative/positive DC

wires into the V+/V

- terminals,

respectivel

STEP 2:

To keep the DC wires from pulling

loose, use a small flat

-blade screwdriver

to tighten the wire

-clamp screws on the

front of the terminal block connector.

STEP 3: Insert the plastic terminal block

connector prongs into the terminal block

recepto

r, which is located on the Industrial

Secure Router’s top panel.

www.ipc2u.ru

www.moxa.pro

- 8 -

Wiring the Digital Inputs

The Industrial Secure Router has one set of digital input, DI. The DI

consists of two contacts of the 2-pin terminal block connector on the

Industrial Secure Router's top panel, which are used for the DC inputs.

The top and front views of one of the terminal block connectors are shown

here.

STEP 1: Insert the negative

(ground)/positive DI wires into the

┴/I

terminals, respectively.

STEP 2:

To keep the DI wires from pulling

loose, use a small flat

-blade screwdriver

to tighten the wire

-clamp screws on the

ront of the terminal block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is located on the Industrial

Secure Router’s top panel.

Communication Connections

Each Industrial Secure Router has three types of communication port:

•1 RJ45 console port (RS-232 interface)

•8 10/100BaseT(X) ports

•2 1000BaseSFP ports

RS-232 Connection

The Industrial Secure Router has one RS-232 (10-pin RJ45) console port,

located on the top panel. Use either an RJ45-to-DB9 (see the cable

following wiring diagrams) to connect the Industrial Secure Router’s

console port to your PC’s COM port. You may then use a console terminal

program, such as Moxa PComm Terminal Emulator, to access the

Industrial Secure Router’s console configuration utility.

RJ45 (10-pin) Console Port Pinouts

Description

----

DSR

RTS

---

TxD

RxD

GND

CTS

DTR

---

www.ipc2u.ru

www.moxa.pro

- 9 -

RJ45 (10-pin) to DB9 (F) Cable Wiring

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on Moxa Industrial Secure Router’s

front panel are used to connect to Ethernet-enabled devices. Most users

will choose to configure these ports for Auto MDI/MDI-X mode, in which

case the port’s pinouts are adjusted automatically depending on the type

of Ethernet cable used (straight-through or cross-over), and the type of

device (NIC-type or HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

10/100Base T(x) RJ45 Pinouts

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

www.ipc2u.ru

www.moxa.pro

- 10 -

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

1000BaseSFP Fiber Port

The Gigabit Ethernet ports on the Industrial Secure Router are SFP slots,

which require Gigabit mini-GBIC fiber transceivers to work properly. Moxa

provides complete transceiver models for various distance requirements.

The concept behind the LC port and cable is quite straightforward.

Suppose you are connecting devices I and II. Unlike electrical signals,

optical signals do not require a circuit in order to transmit data.

Consequently, one of the optical lines is used to transmit data from device

I to device II, and the other optical line is used to transmit data from

device II to device I, for full-duplex transmission.

Remember to connect the Tx (transmit) port of device I to the Rx (receive)

port of device II, and the Rx (receive) port of device I to the Tx (transmit)

port of device II. If you make your own cable, we suggest labeling the two

sides of the same line with the same letter (A-to-A and B-to-B, as shown

below, or A1-to-A2 and B1-to-B2).

LC-Port Pinouts

LC-Port to LC-Port Cable Wiring

ATTENTION

This is a Class 1

Laser/LED product. To avoid causing serious

damage to your eyes, do not stare directly into the Laser Beam.

The Reset Button

Depress the Reset button for five continuous seconds to load the factory

default settings. Use a pointed object, such as a straightened paper clip or

toothpick, to depress the Reset button. When you do so, the STATE LED

will start to blink about once per second. Continue to depress the STATE

LED until it begins blinking more rapidly; this indicates that the button has

been depressed for five seconds and you can release the Reset button to

load factory default settings.

NOTE

DO NOT power off the switch when loading default settings

www.ipc2u.ru

www.moxa.pro

Inhaltsverzeichnis

Andere Moxa Technologies Netzwerk-Router Handbücher

Moxa Technologies

Moxa Technologies EDS-405 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDR-G9010 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies SR3000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-518E Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-518E Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-408A Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies AirWorks AWK-1137C-EU Bedienungsanleitung

Moxa Technologies

Moxa Technologies E Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Handbuch

Moxa Technologies

Moxa Technologies NPort IA5150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell 5004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TSN-G5000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MAR-2000 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NAT-102 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506A-4PoE Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDR-G902 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDR-G903 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1242 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IKS-6324 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-210A-1GTX-1GSFP-4SFP Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise