Moxa Technologies EDS-2008-EL Series Bedienungsanleitung

P/N: 1802020080010

*1802020080010*

EDS-2008-EL/ELP Series

Quick Installation Guide

Moxa EtherDevice Switch

Version 1.0, October 2019

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The EDS-2008-EL/ELP Series has an 8-port combination to simplify

network expansion. There are two housing types available for the user

to select depending on the requirements of their application. The ELP

has a plastic housing and the EL has a metal housing. The compact

switches provide a cost-effective solution for your industrial Ethernet

connection requirements.

The EDS-2008-EL/ELP Series provides 12/24/48 VDC (9.6 to 60 VDC)

power input, and the switches are available with a standard operating

temperature range from -10 to 60°C, or with a wide operating

temperature range from -40 to 75°C (only available for the –T models

in the EL Series). The switches are rugged enough to operate reliably in

harsh industrial environments.

To provide greater versatility for use with applications from different

industries, the EDS-2008-EL/ELP Series also allows users to enable or

disable broadcast storm protection (BSP), Quality of Service (QoS)

function via the DIP switches on the top panel.

The EDS-2008-EL/ELP switches can be easily installed with DIN-rail

mounting as well as distribution boxes. The DIN-rail mounting

capability and IP40 housing with LED indicators ensure that the plug-

and-play EDS-2008-EL/ELP switches are reliable and easy to use.

NOTE

Throughout this Quick Installation Guide, we use EDS as an

abbreviation for Moxa EtherDevice Switch:

EDS = Moxa EtherDevice Switch

ATTENTION

This device complies with part 15 of FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept

any

interference received, including interference that may

cause undesired operations.

Package Checklist

Your EDS is shipped with the following items. If any of these items are

missing or damaged, please contact your customer service

representative for assistance.

•Moxa EtherDevice™ Switch

•Quick installation guide (printed)

•Warranty card

- 3 -

Features

High Performance Network Switching Technology

•10/100BaseT(X) auto-negotiation speed, full/half duplex mode,

auto MDI/MDI-X connection, and 100BaseFX for fiber port models.

•IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X).

•IEEE 802.1p for Quality of Service (QoS) traffic prioritized function.

•Store-and-forward switching process type.

Industrial-grade Reliability

•Broadcast storm protection to prevent network devices from

crashing

Rugged Design

•Operating temperature range from -10 to 60°C, or extended

operating temperature from -40 to 75°C (only available for the –T

models in the EL Series)

•IP40, rugged high-strength case

•DIN-rail or panel mounting ability

WARNING

The

power for this product is intended to be supplied by a

Listed Power Supply, with output marked LPS, and rated to

liver 12 to 48 VDC at a maximum of 0.25 A.

The DC

jack should be used with an LPS unit that is rated to

deliver 12 to 48 VDC at a minimum of

1.1 A. The product

should not be disassembled by operators or service people.

- 4 -

Panel Layout of EDS-2008-EL/EDS-2008-ELP

1. Chassis ground screw

2. Terminal block for power input

3. DIP switch

4. Power LED

5. 10/100 BaseT(X) Port

6. 10/100 BaseT(X) Port LED

7. Port number

8. Model name

- 5 -

Panel Layout of EDS-2008-EL-M-ST/

EDS-2008-EL-M-SC

1. Chassis ground screw

2. Terminal block for power input

3. DIP switch

4. Power LED

5. 10/100 BaseT(X) Port

6. 10/100 BaseT(X) Port LED

7. Port number

8. 10/100 BaseFX Multi-mode ST Port (only for ST models)

9. 10/100 BaseFX Multi-mode SC Port (only for SC models)

10. 10/100 BaseFX Port LED

11. Model name

- 6 -

Mounting Dimensions

EDS-2008-EL Series

EDS-2008-ELP Series

- 7 -

EDS-2008-EL-M-ST Series

EDS-2008-EL-M-SC Series

- 8 -

DIN-rail Mounting

When shipped, the DIN-rail mounting kit is fixed to the back panel of

the EDS. Mount the EDS on the corrosion-free mounting rail that

adheres to the EN 60715 standard.

Suggested Installation Method

STEP 1:

Insert the upper lip of the DIN

rail kit into the mounting rail.

TEP 2:

Press the device towards the

mounting rail until it snaps into

place.

Alternatively, you can use

a screwdriver to attach to the

bottom of the DIN

rail kit and pull

down.

Suggested Removal Method

STEP 1:

Pull down the latch on the DIN

rail kit with a screwdriver.

STEP 2:

Slightly pull the device forward

and lift up to remove it from the

mounting rail.

NOTE

1. If the equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment

may be impaired.

The installation and the safety of any system incorporating

the equipment is the responsibility of the assembler of the

system.

This is an OPEN TYPE module and should be installed in a

safety enclosure with mechanical rigidity and an

appropriate IP rating.

- 9 -

Wall Mounting (optional)

For some applications, you will find it convenient to mount EDS on the

wall, as illustrated below.

There are two options for installation: The first option

is to h

ook the EDS DIN-rail latch on the opening of

the

wall mount kit (see picture above) and then

ount the wall-mount kit on the wall with screws.

(The other option is to perform these two steps in

the other order.)

The heads of the screws should be

less than

6.0 mm in diameter, and the shafts should be less than 3.5 mm in

diameter, as shown in the figure at the right.

NOTE

Before tightening screws into the wall, make sure the screw

head and shank size are suitable by inserting th

e screw into

one of the keyhole

-shaped apertures of the Wall Mounting

Plates.

Do not screw the screws in all the way—leave about 2 mm to allow

room for sliding the wall mount panel between the wall and the screws.

Once the screws are fixed in the

wall, insert the

two screw heads

through the large parts of the

keyhole

-shaped apertures, and

then slide EDS downwards, as

indicated. Tighten the

two

screws for added stability.

WARNING

External metal parts are hot. Take necessary precautions if it is

necessary to touch.

- 10 -

Wiring Requirements

WARNING

Do not disconnect modules or wires

unless the power supply

has been switched off or the area is known to be non

hazardous.

The devices may only be connected to the supply

voltage shown on the type plate.

The devices are designed for operation with a

Safety Extra-L

oltage. Thus, they may only be connected to the supply

voltage connections and to the signal contact with the

Safety

xtra-Low Voltages (SELV) in compliance with IEC950/

EN60950/ VDE0805.

WARNING

Safety First!

Be sure to

disconnect the power cord before installing and/or

wiring your

Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire

and common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If t

he current goes above the maximum ratings, the wiring

could overheat, causing serious damage to your equipment.

You should also pay attention to the following items:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power

wiring in the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb

is that wiring that shares similar electrical characteristics can be

bundled together.

•Keep input wiring and output wiring separated.

•It is strongly advised that you label wiring to all devices in the

system when necessary.

Grounding Moxa EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from

the ground screw to the grounding surface prior to connecting devices.

A 4 mm2conductor must be used when a connection to the external

grounding screw is utilized.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Schalten Handbücher

Moxa Technologies

Moxa Technologies TN-5305-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-G308 Handbuch

Moxa Technologies

Moxa Technologies EDS-G4008 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-316 EtherDevice Handbuch

Moxa Technologies

Moxa Technologies RKS-G4028 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-516A-T Handbuch

Moxa Technologies

Moxa Technologies IKS-6726-8PoE Series Handbuch

Moxa Technologies

Moxa Technologies PT-7728 Series Handbuch

Moxa Technologies

Moxa Technologies TRC-190 Bedienungsanleitung

Moxa Technologies

Moxa Technologies OnCell G3111 Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7710 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-510E Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-405A Handbuch

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-F-24 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-4012 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7528 Handbuch

Moxa Technologies

Moxa Technologies ToughNet TN-5510A-2GLSX-ODC Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies IKS-6728 Series Handbuch

Moxa Technologies

Moxa Technologies ICS-G7526A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-5500A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-G2008-EL Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-G500E Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TN-5308-LV-T Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung