MRC CCM-10 Bedienungsanleitung

PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION

3, Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529 mrc@mrclab.com

MRC.VER.01-07.10

INSTRUCTION MANUAL FOR

Table Cut Mill

&&0

Ⅰ、

OUTLINE

【1】Wind outlet 【7】Current meter

【2】Pulverized material

outlet

【8】Power switch

【3】Shaft base (for holding

the shaft

【9】No Fuse Breaker (NFB)

【4】Loading tube 【10】Wind power adjuster

【5】Loading trough 【11】Pulverizing trough

【6】Screw for tightening

the loading tube

Ⅱ、

OPERATION

1. At first, please make sure whether the wind outlet (【1】) &

pulverized material outlet (【2】) have been covered with the cloth

pipes.

The cloth pipe for covering (【1】) is shorter and there’s a loop for

hanging on the shaft.

The cloth pipe for covering (【2】) is longer.

2. Unlock the screw (【6】) and pull up the upper base, and then insert

into the suitable meshes.

Combination A: Mesh 3~9mm + holder is for getting thick

pulverized materials.

Combination B: Mesh 3~9mm + Mesh 0.3~0.5mm + holder is for

getting thin pulverized materials.

If thick materials were asked to get into thin pulverized materials,

please process combination Afirst and then process combination B.

Such arrangement will gain better effect and keep a longer using

life of the meshes.

3. Please ensure the pulverizing trough (【11】) is empty, or clean it

and then to tighten the screw (【6】).

4. Plug in the socket and switch on (【8】).

5. Let materials be loaded through from the loading trough (【5】) into

the pulverizing trough (【11】) slowly and process pulverizing.

6. The cloth pipe can collect the pulverized materials which should be

small and could pass the meshes to get to the outlet.

7. After pulverizing, please switch off the machine and wait just few

minutes. Finally, the cloth pipe could be loosed and discharge the

pulverized materials.

III

、

CAUTION

1. When NFB is cut off, please turn off the power switch for 10

minutes and press NFB again to restart. The following situations

would be the possible reasons to cause a NFB to be cut off.

1) The speed of material loading is too fast. It’s necessary to

discharge the material more or less before re-starting.

2) When the motor is overloaded or over heat, please turn off the

machine for a while.

When the above situations are solved, users just need push down

the NFB and turn on the power switch.

2. Watch the current meter for avoiding the motor overloading and

being out of order soon.

3. For pulverizing the thick materials, the wind power adjuster (【10】)

could be closed for keeping all materials inside. For pulverizing the

thin materials, the enter gate should be just little opened for

controlling the speed of loading. Use the wind power adjuster

(【10】) to control the wind power.

4. The pulverized trough couldn’t be cleaned up by water.

、

ACCESSORIES

1. Cloth pipes: two pcs (one is long and the other is short)

2. Shaft:1 pc

3. Mesh set: specifics – 75*118mm

、

holder*1pc

mesh size – 0.3m/m * 2 pcs, 0.4m/m * 1 pc,

0.5m/m * 1 pc, 3m/m * 1 pcs,

8m/m * 1 pc, 13m/m * 1 pc

Inhaltsverzeichnis

Andere MRC Laborausrüstung Handbücher

MRC

MRC FDL-18N-70 Series Bedienungsanleitung

MRC

MRC SPC-60 Bedienungsanleitung

MRC

MRC WBL-MINI Bedienungsanleitung

MRC

MRC UT-200A Bedienungsanleitung

MRC

MRC HCEN-24 Bedienungsanleitung

MRC

MRC PCR-300 Bedienungsanleitung

MRC

MRC SRI6PF Bedienungsanleitung

MRC

MRC COL-3500 Bedienungsanleitung

MRC

MRC WBL-100 Bedienungsanleitung

MRC

MRC COT Series Bedienungsanleitung

MRC

MRC SI-500 Mix Smart Bedienungsanleitung

MRC

MRC CENVCC-3 Bedienungsanleitung

MRC

MRC CM-100M3 Bedienungsanleitung

MRC

MRC LOM-150DIG Bedienungsanleitung

MRC

MRC INC-150-CO2-O2 Bedienungsanleitung

MRC

MRC MH-4D Bedienungsanleitung

MRC

MRC STE-V60 Bedienungsanleitung

MRC

MRC YDZ-50K Bedienungsanleitung

MRC

MRC AM-4214SD Bedienungsanleitung

MRC

MRC Mini Roller ROL-01U Bedienungsanleitung

MRC

MRC S2D-300 Bedienungsanleitung

MRC

MRC INE-SGW-1 Bedienungsanleitung

MRC

MRC PCR-IF-8C Bedienungsanleitung

MRC

MRC WBH-060N Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung