MTD World Tiller - Series 240 Bedienungsanleitung

For US Customers: MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

Single-Stage

Snow Thrower

Models240

250

260

S250

S260

PRINTED IN U.S.A.

IMPORTANT:

Read safety rules and instructions carefully before operating equipment.

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-

covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if

any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required

by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark

arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131

Cleveland, Ohio 44136-0019.

FORM NO

769-00805A

(5/7/2004)

Operator’s Manual

For Canadian Customers: MTD Products Ltd., P. O. BOX 1386, KITCHENER, ONTARIO N2G 4J1

TABLE OF CONTENTS

FINDING MODEL NUMBER

This Operator’s Manual is an important part of your new snow thrower. It will help you to assemble, prepare and

maintain the unitfor bestperformance. Please read and understand what it says.

Before you start assembling your new snow thrower, please locate the model plate on the

equipment and copy the information from it in the space provided below. The information on the

model plate is very important if you need help from our Customer Support Department or an

authorized dealer.

• You can locate the model number by standing behind the unit in the operating position and looking down at

the dash panel . A sample model plate is explained below. For future reference,please copy the model

number and the serial number of the equipment in the space below.

ENGINE INFORMATION

The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating,

specifications, warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual packed

separately with your unit for more information.

CALLING CUSTOMER SUPPORT

Please do NOT return the unit to the retailer from which it was purchased, without first contacting Customer Support.

If you have difficulty assembling this product or have any questions regarding the controls, operation or

maintenance of this unit,please call a Customer Support Representataive.

For US Customers: 1- (330) 220-4MTD (4683) or 1- (800)-800-7310

For Canadian Customers: 1-800-668-1238

Please have your unit’s model numberand serial number ready when you call. See previous section to locate this

information. You will be asked to enter the serial number in order to process your call.

Content Page

Customer Support 2

Important Safe Operation Practices 3

Assembly 5

Controls 6

Operation 7

Ajustments 8

Maintenance 8

Accessories & Kits 11

Illustrated Parts List 12

Warranty 14

Content Page

USA-www.mtdproducts.com 1-800-800-7310

CAN-www.mtdcanada.com 1-800-668-1238

MTD LLC

CLEVELAND, OH 44136

MTD PRODUCTS LIMITED

KITCHENER, ON N2G 4J1

Model Number

Numéro de modèle

XXXXXXXXXXX XXXXXXXXXXX

Serial Number

Numéro de sérier

Copy the model number here:

Copy the serial number here:

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could endanger the

personal safety and/or property of yourself and others. Read and follow all instructions in this manual before

attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you

see this symbol—heed its warning.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals

known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with

any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This

machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety

instructions could result in serious injury or death.

Training

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe place

for future and regular reference and for ordering

replacement parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the machine and disengage them

quickly.

3. Never allow children under 14 years old to operate this

machine. Children 14 years old and over should read and

understand the operation instructions and safety rules in

this manual and should be trained and supervised by a

parent.

4. Neverallowadults to operate thismachinewithout proper

instruction.

5. Thrown objects can cause serious personal injury. Plan

your snow throwing pattern to avoid discharge of material

toward roads, bystanders and the like.

6. Keep bystanders, helpers, pets and children at least 75

feet from the machine while it is in operation. Stop

machine if anyone enters the area.

7. Exercise caution to avoid slipping or falling, especially

when operating in reverse.

Preparation

1. Thoroughly inspect the area wheretheequipment is to be

used. Remove all door mats, newspapers, sleds, boards,

wires and other foreign objects which could be tripped

over or thrown by the auger/impeller.

2. Always wear safety glasses or eye shields during

operation and while performing an adjustment or repair to

protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

3. Do not operate without wearing adequate winter outer

garments. Do not wear jewelry, long scarves or other

loose clothing which could become entangled in moving

parts. Wear footwear which will improve footing on

slippery surfaces.

4. Use a grounded extension cord and receptacle for all

units with electric start engines.

5. Adjust collector housing height to clear gravel or crushed

rock surfaces.

6. Disengage the control handle before starting the engine.

7. Never attempt to make any adjustments while engine is

running, except where specifically recommended in the

operator’s manual.

8. Let engine and machine adjust to outdoor temperature

before starting to clear snow.

9. To avoid personal injury or property damage use extreme

care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive. Serious

personal injury can occur when gasoline is spilled on

yourself or your clothes which can ignite. Wash your skin

and change clothes immediately.

a. Use only an approved gasoline container.

b. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

c. Never fuel machine indoors.

d. Never remove gas cap or add fuel while the

engine is hot or running.

e. Allow engine to cool at least two minutes before

refueling.

f. Neverover fill fueltank.Fill tank to no more than½

inch below bottom of filler neck to provide space

for fuel expansion.

g. Replace gasoline cap and tighten securely.

h. If gasoline is spilled, wipe it off the engine and

equipment. Move machine to another area. Wait 5

minutes before starting the engine.

i. Never store the machine or fuel container inside

where there is an open flame, spark or pilot light

(e.g. furnace, water heater, space heater, clothes

dryer etc.).

j. Allow machine to cool at least 5 minutes before

storing.

Operation

1. Do not put hands or feet near rotating parts, in the auger

housing or discharge chute. Contact with the rotating

parts can amputate hands and feet.

2. The auger control handle is a safety device. Never

bypass its operation. Doing so, makes the machine

unsafe and may cause personal injury.

3. The control handle must operate easily in both directions

and automatically return to the disengaged position when

released.

4. Never operate with a missing or damaged discharge

chute. Keep all safety devices in place and working.

5. Never run an engine indoors or in a poorly ventilated

area. Engine exhaust contains carbon monoxide, an

odorless and deadly gas.

6. Do not operate machine while under the influence of

alcohol or drugs.

7. Muffler and engine become hot and can cause a burn. Do

not touch.

8. Exercise extreme caution when operating on or crossing

gravel surfaces. Stay alert for hidden hazards or traffic.

9. Exercise caution when changing direction and while

operating on slopes.

10. Plan your snow throwing pattern to avoid discharge

towards windows, walls, cars etc. To avoid property

damage or personal injury caused by a ricochet.

11. Never direct discharge at children, bystanders and pets

or allow anyone in front of the machine.

12. Do not overload machine capacity by attempting to clear

snow at too fast of a rate.

13. Neveroperatethis machine withoutgoodvisibility or light.

Always be sure of your footing and keep a firm hold on

the handles. Walk, never run.

14. Disengage power to the auger/impeller when

transporting or not in use.

15. Never operate machine at high transport speeds on

slippery surfaces. Look down and behind and use care

when in reverse.

16. If the machine should start to vibrate abnormally, stop the

engine, disconnect the spark plug and ground it against

the engine. Inspect thoroughly for damage. Repair any

damage before starting and operating.

17. Disengage the control handle and stop engine before you

leave the operating position (behind the handles). Wait

until the auger comes to a complete stop before

unclogging the discharge chute, making any

adjustments, or inspections.

18. Never put your hand in the discharge or collector

openings. Always use a clearing tool to unclog the

discharge opening.

19. Use only attachments and accessories approved by the

manufacturer.

20. If situations occur which are not covered in this manual,

use care and good judgment. Call customer assistance

for the name of your nearest servicing dealer.

Maintenance And Storage

1. Never tamper with safety devices. Check their proper

operation regularly.

2. Disengage the control handle and stop engine. Wait until

the auger/impeller come to a complete stop. Disconnect

the spark plug wire and ground against the engine to

prevent unintended starting before cleaning, repairing, or

inspecting.

3. Check bolts, and screws for proper tightness at frequent

intervals to keep the machine in safe working condition.

Also, visually inspect machine for any damage.

4. Do not change the engine governor setting or over-speed

the engine. The governor controls the maximum safe

operating speed of the engine.

5. Snow thrower shave plates and skid shoes are subject to

wear and damage. For your safety protection, frequently

check all components and replace with original

equipment manufacturer’s (O.E.M.) parts only. “Use of

parts which do not meet the original equipment

specifications may lead to improper performance and

compromise safety!”

6. Check controls periodically to verify they engage and

disengage properly and adjust, if necessary. Refer to the

adjustment section in this operator’s manual for

instructions.

7. Maintain or replace safety and instruction labels, as

necessary.

8. Observe proper disposal laws andregulations forgas, oil,

etc. to protect the environment.

9. Prior to storing, run machine a few minutes to clear snow

from machine and prevent freeze up of auger/impeller.

10. Never store the machine or fuel container inside where

there is an open flame, spark or pilot light such as a water

heater, furnace, clothes dryer etc.

11. Always refer to the operator’s manual for proper

instructions on off-season storage.

Your Responsibility:

• Restrict the use of this power machine to persons who

read, understand and follow the warnings and

instructions in this manual and on the machine.

• FUEL MIXTURE 50:1 OR 2%

• MIX QUALITY 2 CYCLE OIL (TC-W11 OR TC-W3) WITH COLD WEATHER

GAS IN GAS CAN ONLY

1.)

INSERT IGNITION KEY, TURN TO RUN POSITION.

2.)

MOVE CHOKE LEVER TO FULL (ON) POSITION. PUSH PRIMER BUTTON 3x.

3.)

ROPE START: PULL SLOWLY UNTIL HARDER TO PULL, THEN PULL RAPIDLY TO START.

REPEAT PRIMING IF NEEDED.

ELECTRIC START: DO NOT USE IN RAIN. CONNECT POWER CORD AND PUSH STARTER

BUTTON. REPEAT PRIMING IF NEEDED.

4.) MOVE CHOKE SLOWLY TO OFF POSITION.

5.) TO STOP ENGINE: TURN KEY TO STOP POSITION.

RUN

PREPARATIONS AND STARTING INSTRUCTIONS:

AVANT LE DÉMARRAGE ET MISE EN MARCHE DU MOTEUR:

• MÉLANGE DE CARBURANT À UN TAUX DE 50 À 1 OU 2%.

• MÉLANGE UNE HUILE DE QUALITÉ POUR MOTEURS À DEUX TEMPS

(TC-W11 OR TC-W3) AVEC UNE ESSENCE PRÉPARÉE POUR TEMPS FROID.

1.) ENFONCEZ LA CLÉ DE CONTACT. TOURNEZ LA CLÉ À LA POSITION «RUN».

2.) PLACEZ LA MANETTE DU VOLET DE DÉPART À LA POSITION VOLET FERMÉ «ON».

ENFONCEZ TROIS FOIS LE BOUTON D'AMORÇAGE.

3.) DÉMARREUR À LANCEUR: TIREZ LA CORDE LENTEMENT JUSQU'À CE QUE VOUS SENTIEZ UNE

LÉGÈRE RÉSISTANCE, PUIS TIREZ RAPIDEMENT POUR DÉMARRER. RÉPÉTEZ L'AMORÇAGE AU BESOIN.

DÉMARREUR ÉLECTRIQUE: N'EMPLOYEZ PAS DANS LA PLUIE. BRANCHEZ LE FIL ÉLECTRIQUE

ET APPUYEZ SUR LE BOUTON DU DÉMARREUR. RÉPÉTEZ L'AMORÇAGE AU BESOIN.

4.) OUVREZ LENTEMENT LE VOLET DE DÉPART.

5.) POUR ARRÊTEZ LE MOTEUR: TOUREZ LA CLÉ

À LA POSITION «STOP».

BOUTON D'AMORÇAGE

PRIMER BUTTON

DANGER

NEVER PUT HAND IN CHUTE. CAN

AMPUTATE

HANDS AND FINGERS.

STOP ENGINE AND AUGER BEFORE USING

CLEAN-OUT TOOL OR STICK.

ARRÊTEZ LE MOTEUR ET LA TARIÈRE AVANT

D'UTILISER L'OUTIL DE DÉGAGEMENT

DE LA GOULOTTE OU UN BÂTON.

NE PLACEZ JAMAIS VOS MAINS DANS LA

GOULOTTE. LES PIÈCES EN MOUVEMENT

PEUVENT AMPUTER MAINS ET DOIGTS.

FOR TURNING,

NOT LIFTING

POUR TOURNER,

PAS POUR LE LEVAGE

SECTION 2: ASSEMBLING YOUR SNOW THROWER

NOTE: This Operator’s Manual covers several models.

Snow thrower features vary by model. Not all

features discussed in this manual are applicable to all

snow thrower models.

Unpacking From Carton

• Cut along corners of the carton and lay it down flat.

Remove packing material.

• Remove any loose parts included with unit (i.e.,

operator’s manual, etc.).

• Roll unit out of carton. Check carton thoroughly for

any remaining loose part.

Items Required For Assembly

1. Engine oil

2. Fresh gasoline

Before Assembly

WARNING: Disconnect the spark plug wire

and ground it against the engine to prevent

unintended starting.

Positioning the Upper Handle

Making sure not to pinch the cable inthe

process, pivot the upper handle into the

operating position as illustrated until it clicks

into place.

Tighten the wing knobs to secure the handle in

place.

Assembling the Discharge Chute

For shipping reasons, the snow thrower has

been packaged with the upper chute pivoted all

the way down. To pivot it upward, proceed as

follows:

1. Turn the chute until the chute opening is facing

straight ahead.

2. Remove the wing knob, flat washer and carriage

bolt from the lower chute.

3. Pivot the upper chute upward over the lip on the

lower chute so that there is NO gap between the

upper chute and the lower chute.

4. Resecure with the hardware justremoved.

CAUTION: Do not use the Chute

Handle to lift the machine.

SECTION 3: KNOW YOUR SNOW THROWER

Figure 1

IMPORTANT:

This unit runs on a mixture of gasoline

and oil. Do NOT operate the snow thrower without first

reading the engines operator’s manual for instructions

regarding proper fuel and engine oil.

Choke Lever

Activating the choke control closes the choke plate on

the carburetor and aids in starting the engine. Refer to

the engine manual packed with the snow thrower for

more detailed instructions regarding the choke.

Primer

Depressing the primer forces fuel

directlyintotheengine’scarburetor to

aid in cold-weather starting. Refer to

the engine manual packed with the

snow thrower for more detailed

instructions regarding the primer.

Ignition Key

The ignition key must be present,

inserted in the key switch, and in the

“ON” position for the engine to start.

Starter Handle

The starter handle is used to manually start the engine.

Electric Starter Button (If so equipped)

Pressing the electric starter button engages the

engine’s electric starter when plugged into a 120V

power source.

Electric Starter Plug (If so equipped)

Requires use of a two-prong outdoor extension cord

(packed with the snow thrower) and a 120V power

source/wall outlet.

Spark Plug Cover

Remove the spark plug cover to access the engine’s

spark plug located beneath it.

Auger

When engaged, the augers rotation draws snow into

the auger housing and throws it out the discharge

chute. The rubber paddles on the augers also aid in

propelling the snow thrower as they come in contact

with the pavement.

Auger Control Handle

Located on the upper handle, the auger control handle

is used to engage and disengage drive to the auger.

Squeeze thecontrol handle againstthe upper handleto

engage the auger; release it to disengage.

Discharge Chute / Chute Handle

Rotate the discharge chute to the left or right using the

chute handle. The pitch of the discharge chute controls

the angle at which the snow is thrown. Loosen the wing

knob on the side of the discharge chute before pivoting

the discharge chute upward or downward. Retighten

the knob once the desired position has been achieved.

Shave Plate

The shave plate maintains contact with the pavement

as the snow thrower is propelled,allowing the snow

close to the pavement’s surface to be discharged.

Ignition Key

Electric Starter Plug

Choke Lever

Spark Plug Cover

Primer

Upper Handle

Fuel Cap

(If So Equipped)

Electric Starter Button

Auger

Shave Plate

Starter Handle*

Discharge Chute

Auger Control

Handle

Chute Handle

* Styles vary by model

(If So Equipped)

OFF

CHOKE

SECTION 4: OPERATING YOUR SNOW THROWER

WARNING: Before starting the engine,

read, understand, and follow all instructions

and warnings on the machine and in this

manual before operating.

Fuel And Oil Mixture

WARNING: Use extreme care when

handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

Never fuel machine indoors or while the

engine is hot or running. Extinguish cigarettes,

cigars, pipes and othersources of ignition.

IMPORTANT:

This unit runs on a mixture of gasoline

and oil. Do NOT operate the snow thrower without first

reading the engines operator’s manual for detailed

instructions regarding proper fuel and engine oil.

Do NOT operate the snow thrower without the fuel cap

securely in place on the fuel tank.

Positioning the Discharge Chute

• Loosen the wing knob found on the left side of the

discharge chute and pivot the upper chute upward

or downward to the desired pitch. Retighten the

wing knob before operating the snow thrower.

• Rotate the discharge chute to the left or right using

the chute handle. See Figure 2.

Starting the Engine

• Refer to the separate engine manual packed with

the snow thrower for detailed instructions regarding

starting the engine.

Clearing Snow

NOTE: For more efficient snow clearing, discharge

snow downwind whenever possible.

WARNING: Never operate the snow thrower

with bystanders in front of or near the

discharge chute opening.

• Engage the augerby squeezing the control handle

against the upper handle. See Figure 2.

• Lift up slightly on the handle to allow the rubber

paddles on the augerto contact the pavement and

propel the snow thrower forward.

IMPORTANT:

Excessive upward pressure on the handle

will result in premature wear on the rubber auger

paddles or possible damage or marking of pavement.

Resulting wear would not be covered by warranty.

• As the snow thrower starts to move, maintain a firm

hold on the handle,and guide the snow thrower

along the path to be cleared.

Figure 2

Figure 3

• Release the auger control handle to stop the snow

throwing action and the forward motion.

Stopping the Engine

WARNING: Muffler, engine and surrounding

areas become hot and can cause a burn. Do

not touch.

• After clearing snow, allow the engine to run for an

extra few minutes before storing to help dry any

moisture on the engine.

• To stop the engine: Turn the ignition key

counterclockwise to the OFF position. Remove the

key form the snow thrower’s ignition switch before

storing.

Wing Knob

Chute Handle Upper Chute

Auger Control Handle

SECTION 5: MAKING ADJUSTMENTS

WARNING: NEVER attempt to make any

adjustments while the engine is running.

Shave Plate

• To check the adjustment of the shave plate, place

the unit on a level surface. The wheels, shave plate

and augers should all contact the level surface.

Note that if the shave plate is adjusted too high,

snow may blow under the housing. If the shave

plate wears out excessively, or the unit will not self-

propel, the shave plate may be adjusted too low.

NOTE: On new units or units with a new shave plate

installed, the augers may be slightly off the ground.

• To adjust, tip the snow thrower back so that it rests

on the handle. Loosen the lock nuts from the

carriage bolts which secure the shave plate to the

housing. See Figure 4.

• Move the shave plate to desired position and

retighten the nuts and bolts. Make certain all four

nuts are securely tightened.

Figure 4

SECTION 6: MAINTAINING YOUR SNOW THROWER

WARNING: Before servicing, repairing, or

inspecting, disengage the control handle and

stop engine. Wait until all moving parts have

come to a complete stop. Disconnect spark

plug wire and ground it against the engine to

prevent unintended starting.

Lubrication

• Lubricate pivotpoints on the control handle and the

extension spring at the end of the clutch cable with

a light oil once every season and before storage of

the snow thrower at the end of the season.

Hardware

Check the engine and snow thrower frequently for

loose or missing hardware, and tighten or replace as

necessary.

Replacing the Drive Belt

The snow thrower’s drive belt is subject to wear and

should be replaced if any signs of cracking, shredding

or rotting is present.To change the drive belt, proceed

as follows:

• Remove the belt cover from the left side of the

snow thrower’s auger housing by unthreading the

five hex screws which secure it in place.

• Gently grasp the idler bracket and pivot it upward to

ease tension on the drive belt. See Figure 5.

• While holding the idler bracket up, carefully slip the

drive belt off the engine pulley. See Figure 5.

Figure 5

• Carefully release the idler bracket and allow it to

pivot downward.

• Carefully slip the drive belt off the auger pulley,

freeing it from the snow thrower. See Figure 5.

Carriage Bolts Shave Plate

Auger Pulley

Idler Bracket Engine

Pulley

Drive Belt

• Install the replacement drive belt by following the

preceding steps in reverse order.

• Reattach the belt cover with the five hex screws

removed earlier.

Replacing the Shave Plate

The shave plate is subject to wear and should be

checked periodically. There are two wearing edges and

the shave plate can be reversed after one side wears

out.

To replace (or reverse) the shave plate, proceed as

follows:

• Remove the four carriage bolts and hex lock nuts

which secure it to the snow thrower’s auger

housing. Refer to Figure 4.

• Install the new shave plate (or reverse the existing

one,if bothsides are notyet worn),makingsurethe

heads of the carriage bolts are on the inside of the

housing. The lock nuts should be on theoutside of

the housing.

• Adjust the shave plate as instructed in the Making

Adjustments section of this manual.

• Tighten the nuts securelybefore operating the

snow thrower.

Replacing the Auger’s Rubber Paddles

The snow thrower auger’s rubber paddles are subject

to wear and should be replaced if any signs of

excessive wear is present.

To change the rubber paddles, proceed as follows:

• Remove the existing rubber paddles by

unthreading the self-tapping screws which secure

them to the auger.

• Secure the replacement rubber paddles to the

auger using the hardware removed earlier.

Engine

Refer to the separate engine manual packed with the

snow thrower for detailed instructions regarding all

engine-related maintenance.

SECTION 7: OFF-SEASON STORAGE

WARNING: Never store engine with fuel in

tank indoors or in enclosed, poorly ventilated

areas where fuel fumes may reach an open

flame, spark or pilot light as on a furnace,

water heater, clothes dryer, or other gas

appliance.

• Clean snow thrower thoroughly.

• Lubricate as instructed in the Maintaining Your

Snow Thrower section of this manual.

• Refer to the separate engine manual packed with

the snow thrower for detailed instructions regarding

all engine-related storage instructions.

• Store the snow thrower in a clean, dry area.

• Place blocks underthe front of the auger housing

so that the snow thrower is not resting on the

rubber auger paddles. The rubber can become

misshaped if it supports the weight of the snow

thrower for several months of storage.

NOTE: When storing any type of power equipment in a

poorly ventilated or metal storage shed, care should be

taken to rustproof the equipment, especially springs,

cables and all moving parts.

SECTION 8: TROUBLESHOOTING GUIDE

Problem Cause Remedy

Engine fails to start 1. Key not in ignition switch or not in ON position.

2. Fuel tank empty, or stale fuel

3. Blocked fuel line

4. Spark plug wire disconnected

5. Faulty spark plug

1. Insert key and turn to ON position

2. Fill tank with clean fresh gasoline/oil

mixture as specified in the engine manual.

3. Clean fuel line

4. Connect wire to spark plug.

5. Clean spark plug, readjust gap, or replace.

Engine runs erratic 1. Unit running with choke in ON position

2. Fuel line blocked, or stale fuel

3. Water or dirt in fuel system

4. Carburetor out of adjustment

1. Move choke lever to OFF position.

2. Clean fuel line and fill tank with fresh, clean

gasoline/oil.

3. Refer to engine manual for remedy.

4. Refer to engine manual.

Loss of power 1. Spark plug wire loose

2. Engine exhaust pipe plugged. 1. Connect and tighten spark plug wire.

2. Remove obstruction from exhaust pipe.

Excessive vibration 1. Loose parts or damaged auger 1. Stop engine immediately and disconnect

spark plug wire. Check for possible

damage. Tighten all bolts and nuts. Repair

as needed. If the problem persists, take unit

to an authorized service dealer.

Unit fails to self-propel 1. Drive belt damaged 1. Inspect the drive belt for damage and

replace if necessary as instructed in this

manual.

Unit fails to discharge

snow 1. Discharge chute clogged

2. Foreign object lodged in auger

3. Drive belt damaged

1. Stop engine immediately and disconnect

spark plug wire. Clean discharge chute and

the auger housing.

2. Stop engine immediately and disconnect

spark plug wire. Remove object.

3. Inspect the drive belt for damage and

replace if necessary as instructed in this

manual.

Andere Handbücher für World Tiller - Series 240

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MTD Schneemobil Handbücher

MTD

MTD 315-140-000 Bedienungsanleitung

Beliebte Schneemobil Handbücher anderer Marken

BRP

BRP Ski-Doo MXZ 120 2023 Bedienungsanleitung

Arctic Cat

Arctic Cat ZR 900 Series 2006 Bedienungsanleitung

Arctic Cat

Arctic Cat Wildcat EFI Mountain Cat 1994 Bedienungsanleitung

Ski-Doo

Ski-Doo Formula Plus 1985 Bedienungsanleitung

BOMBARDIER

BOMBARDIER Ski-Doo Alpine 74 1959 Bedienungsanleitung

Arctic Cat

Arctic Cat Cougar Bedienungsanleitung

Yamaha

Yamaha SnoScoot SXR2NJ Bedienungsanleitung

Yamaha

Yamaha VX500XTB Bedienungsanleitung

Yamaha

Yamaha RS VENTURE 2014 Bedienungsanleitung

Polaris

Polaris RMK Shift Bedienungsanleitung

Yamaha

Yamaha VK540EF Bedienungsanleitung

Ski-Doo

Ski-Doo 1982 Elite Bedienungsanleitung

Yamaha

Yamaha VK540EF Bedienungsanleitung

BOMBARDIER

BOMBARDIER ski-doo Nordic 640ER 1974 Bedienungsanleitung

BOMBARDIER

BOMBARDIER ski-doo OLYMPIQUE 300 1974 Bedienungsanleitung

Yamaha

Yamaha SXV4NP Bedienungsanleitung

Ski-Doo

Ski-Doo MX Bedienungsanleitung

Ohlins

Ohlins PB 616 Bedienungsanleitung