MULTIQUIP PRO12C Bedienungsanleitung

OPERATION MANUAL

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

To ﬁnd the latest revision of this

publication, visit our website at:

www.multiquip.com

SERIES

MODELS

PRO12C/PRO12E51C

PRO12E53C/PRO12E53-460VC

HYDRAULIC PLASTER/MORTAR MIXER

(HONDA GX390RT2-QNB2 GASOLINE ENGINE/

TECO WESTINGHOUSE 5HP ELECTRIC MOTOR)

Revision #0 (07/16/20)

To ﬁnd the latest revision of this publication or

associated parts manual, visit our website at:

www.multiquip.com

PAGE 2 — PRO12C HYDRAULIC MIXER • OPERATION MANUAL — REV. #0 (07/16/20)

PROPOSITION 65 WARNING

PRO12C HYDRAULIC MIXER • OPERATION MANUAL — REV. #0 (07/16/20) — PAGE 3

SILICOSIS/RESPIRATORY WARNINGS

Grinding/cutting/drilling of masonry, concrete, metal and

other materials with silica in their composition may give

off dust or mists containing crystalline silica. Silica is a

basic component of sand, quartz, brick clay, granite and

numerous other minerals and rocks. Repeated and/or

substantial inhalation of airborne crystalline silica can

cause serious or fatal respiratory diseases, including

silicosis.Inaddition, California and some other

authorities have listed respirable crystalline silica as a

substance known to cause cancer. When cutting such

materials, always follow the respiratory precautions

mentioned above.

WARNING

Grinding/cutting/drilling of masonry, concrete, metal and

other materials can generate dust, mists and fumes

containing chemicals known to cause serious or fatal

injury or illness, such as respiratory disease, cancer,

birth defects or other reproductive harm. If you are

unfamiliar with the risks associated with the particular

process and/or material being cut or the composition of

the tool being used, review the material safety data

sheet and/or consult your employer, the material

manufacturer/supplier, governmental agencies such as

OSHA and NIOSH and other sources on hazardous

materials. California and some other authorities, for

instance, have published lists of substances known to

cause cancer, reproductive toxicity,or other harmful

effects.

Control dust, mist and fumes at the source where

possible. In this regard use good work practices and

follow the recommendations of the manufacturers or

suppliers, OSHA/NIOSH, and occupational and trade

associations.Water should be used for dust

suppression when wet cutting is feasible. When the

hazards from inhalation of dust, mists and fumes cannot

be eliminated, the operator and any bystanders should

always wear a respirator approved by NIOSH/MSHA for

the materials being used.

WARNING

SILICOSIS WARNING RESPIRATORY HAZARDS

PAGE 4 — PRO12C HYDRAULIC MIXER • OPERATION MANUAL — REV. #0 (07/16/20)

TABLE OF CONTENTS

PRO12C Hydraulic

Plaster/Mortar Mixer

Proposition 65 Warning ........................................... 2

Silicosis/Respiratory Warnings ................................ 3

Table of Contents..................................................... 4

Safety Information ............................................. 6–10

Speciﬁcations ........................................................ 11

Dimensions............................................................ 12

General Information............................................... 13

Components (Mixer) ........................................ 14–15

Components (Engine)............................................ 16

Electric Motor ........................................................ 17

Inspection ........................................................ 18–20

Paddle Blade Adjustment ...................................... 21

Operation......................................................... 22–26

Maintenance.................................................... 27–29

Troubleshooting (Engine)................................. 31–32

Troubleshooting (Motor)......................................... 33

Troubleshooting (Mixer) ......................................... 34

Hydraulic Hose Connections ................................. 35

Hydraulic System Locator...................................... 36

Hydraulic System Diagram .................................... 37

Electric Motor (Single Phase) Wiring Diagram ...... 38

Electric Motor (Three Phase) Wiring Diagram....... 39

NOTICE

Speciﬁcations are subject to change without notice.

PRO12C HYDRAULIC MIXER • OPERATION MANUAL — REV. #0 (07/16/20) — PAGE 5

NOTES

PAGE 6 — PRO12C HYDRAULIC MIXER • OPERATION MANUAL — REV. #0 (07/16/20)

SAFETY INFORMATION

DO NOT operate or service the equipment before reading

the entire manual. Safety precautions should be followed

at all times when operating this equipment.

Failure to read and understand the safety

messages and operating instructions could

result in injury to yourself and others.

SAFETY MESSAGES

The four safety messages shown below will inform you

about potential hazards that could injure you or others.The

safety messages speciﬁcally address the level of exposure

to the operator and are preceded by one of four words:

DANGER, WARNING, CAUTION

or NOTICE.

SAFETY SYMBOLS

DANGER

Indicates a hazardous situation which, if not avoided,

WILL result in DEATH or SERIOUS INJURY.

WARNING

Indicates a hazardous situation which, if not avoided,

COULD result in DEATH or SERIOUS INJURY.

CAUTION

Indicates a hazardous situation which, if not avoided,

COULD result in MINOR or MODERATE INJURY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this

equipment will be referenced with hazard symbols which

may appear throughout this manual in conjunction with

safety messages.

Lethal exhaust gas hazards

Explosive fuel hazards

Burn hazards

Rotating parts hazards

Symbol Safety Hazard

PRO12C HYDRAULIC MIXER • OPERATION MANUAL — REV. #0 (07/16/20) — PAGE 7

SAFETY INFORMATION

GENERAL SAFETY

CAUTION



NEVER operate this equipment without proper protective

clothing, shatterproof glasses, respiratory protection,

hearing protection, steel-toed boots and other protective

devices required by the job or city and state regulations.



Avoid wearing jewelry or loose-ﬁtting clothes that may

snag on the controls or moving parts as this can cause

serious injury.



DO NOT operate this equipment when not

feeling well due to fatigue, illness or when

on medication.



NEVER operate this equipment under the

inﬂuence of drugs or alcohol.



ALWAYS clear the work area of any debris, tools, etc.

that would constitute a hazard while the equipment is

in operation.



ALWAYS check the equipment for loosened threads or

bolts before starting.



NEVER use the equipment for any purpose other than

its intended purposes or applications.

NOTICE



This equipment should only be operated by trained and

qualiﬁed personnel 18 years of age and older.



Whenever necessary, replace nameplate, operation and

safety decals when they become difﬁcult to read.



Manufacturer does not assume responsibility for any

accident due to equipment modiﬁcations. Unauthorized

equipment modiﬁcation will void all warranties.

NEVER

use accessories or attachments that are not

recommended by Multiquip for this equipment. Damage

to the equipment and/or injury to the user may result.

ALWAYS know the location of the nearest

ﬁre extinguisher.

ALWAYS know the location of the nearest

ﬁrst aid kit.

ALWAYS know the location of the nearest phone or

keep

a phone on the job site

. Also, know the phone numbers

of the nearest ambulance, doctor and ﬁre department

This information will be invaluable in the case of an

emergency.

MIXER SAFETY

DANGER

NEVER operate the equipment in an explosive

atmosphere or near combustible materials.An

explosion or ﬁre could result causing severe

bodily harm or even death.

NEVER mix ﬂammable or explosive substances.

PAGE 8 — PRO12C HYDRAULIC MIXER • OPERATION MANUAL — REV. #0 (07/16/20)

SAFETY INFORMATION

WARNING



DO NOT place your hands inside the drum

while starting or operating this equipment.



NEVER disconnect any emergency

or safety devices.These devices are

intended for operator safety. Disconnection of these

devices can cause severe injury, bodily harm or even

death. Disconnection of any of these devices will void

all warranties.



Before operating the mixer, ensure that the safety grate

is in position and correctly ﬁtted.

CAUTION



NEVER lubricate components or attempt service on a

running machine.

NOTICE



ALWAYS keep the machine in proper running condition.



ALWAYS ensure the mixer is on level ground before

mixing.



Fix damage to the machine and replace any broken

parts immediately.



DO NOT tip the mixer onto the drum mouth while the

drum is rotating.



Ensure the drum is rotating while ﬁlling and emptying

the drum.



ALWAYS store equipment properly when it is not being

used. Equipment should be stored in a clean, dry location

out of the reach of children and unauthorized personnel.



ALWAYS deploy stabilizer jack stands prior to use.

ENGINE SAFETY (GASOLINE MODELS ONLY)

DANGER



Engine fuel exhaust gases contain poisonous carbon

monoxide. This gas is colorless and odorless, and can

cause death if inhaled.



The engine of this equipment requires an adequate

free ﬂow of cooling air. NEVER

operate this equipment

in any enclosed or narrow

area where free ﬂow of the

air is restricted. If the air

ﬂow is restricted it will cause

injury to people and property

and serious damage to the

equipment or engine.

WARNING

DO NOT

place hands or fingers inside the engine

compartment while the engine is running.

NEVER

operate the engine with heat shields or

guards removed.

Keep ﬁngers, hands, hair and clothing away

from all moving parts to prevent injury.

DO NOT remove the engine oil drain plug

while the engine is hot. Hot oil will gush out of the oil

tank and severely scald any persons in the general area

of the mixer.

CAUTION

NEVER touch the hot exhaust manifold,

mufﬂer or cylinder. Allow these parts to cool

before servicing the equipment.



Make certain the operator knows how to and is capable

of turning the engine OFF in case of an emergency.

NOTICE

NEVER

run the engine without an air ﬁlter or with a dirty

air ﬁlter. Severe engine damage may occur. Service the

air ﬁlter frequently to prevent engine malfunction.

NEVER tamper with the factory settings

of the engine or engine governor. Damage

to the engine or equipment can result

if operating in speed ranges above the

maximum allowable.

PRO12C HYDRAULIC MIXER • OPERATION MANUAL — REV. #0 (07/16/20) — PAGE 9

SAFETY INFORMATION

FUEL SAFETY (GASOLINE MODELS ONLY)

DANGER



NEVER add fuel to the equipment if it is placed inside a

truck bed with a plastic liner. The possibility exists of

explosion or ﬁre due to static electricity.



NEVER start the engine near spilled fuel or combustible

ﬂuids. Fuel is extremely ﬂammable and its vapors can

cause an explosion if ignited.



ALWAYS refuel in a well-ventilated area, away from

sparks and open ﬂames.



ALWAYS use extreme caution when working with

ﬂammable liquids.



DO NOT ﬁll the fuel tank while the engine is running

or hot.



NEVER overﬁll the tank, as spilled fuel can ignite if it

comes into contact with hot engine parts or sparks from

the ignition system.



Store fuel in appropriate containers, in well-ventilated

areas and away from sparks and ﬂames.



NEVER use fuel as a cleaning agent.



NEVER smoke around or near the

equipment. Fire or explosion could result

from fuel vapors or if fuel is spilled on a

hot engine.

FUEL

GENERATOR SAFETY

If using a generator to power the mixer, refer

to the applicable generator manual safety

information section.

ELECTRIC MOTOR SAFETY

(ELECTRIC MODELS ONLY)

NOTICE



Operate the electric motor only at the speciﬁed voltage

indicated on the nameplate.

NEVER spray water onto the electric motor.

ALWAYS

disconnect the AC power plug from the power

source before moving the mixer.

ALWAYS make sure the ON/OFF switch

on the electric motor is in the OFF position

when not in use and before inserting the

mixer’s power plug into an AC receptacle.

POWER CORD/CABLE SAFETY

DANGER

NEVER let power cords or cables lay in water.

DO NOT use damaged or worn

cables or cords when

connecting equipment to a generator. Inspect for cuts in

the insulation.

NEVER grab or touch a live power

cord or cable with wet hands. The

possibility exists of electrical shock,

electrocution or death.



Make sure power cables are securely connected.

Incorrect connections may cause electrical shock and

damage to the mixer.

CAUTION



Ensure that cables and cords will not be tripped over or

trapped underneath the mixer.

NOTICE

ALWAYS

make sure that the proper power or extension

cord has been selected for the job.

PAGE 10 — PRO12C HYDRAULIC MIXER • OPERATION MANUAL — REV. #0 (07/16/20)

SAFETY INFORMATION

TRANSPORTING SAFETY

CAUTION



DO NOT allow any person or animal to stand underneath

the equipment while it is being lifted.

NOTICE



Make sure forklift forks are inserted as far as possible into

pockets (if applicable) when lifting the mixer.



ALWAYS shut down the engine before transporting.



DO NOT lift the equipment while the engine is running.



Tighten the fuel tank cap securely and close the fuel

cock to prevent fuel from spilling.



NEVER lift the machine to unnecessary heights.



ALWAYS tie down the equipment during transport by

securing it with rope.



DO NOT tip the engine to extreme angles during lifting as

this may cause oil to gravitate into the cylinder head, making

engine starting difﬁcult.

ENVIRONMENTAL SAFETY/

DECOMMISSIONING

NOTICE

Decommissioning is a controlled process used to safely

retire a piece of equipment that is no longer serviceable.

If the equipment poses an unacceptable and unrepairable

safety risk due to wear or damage or is no longer cost

effective to maintain (beyond life-cycle reliability) and is to

be decommissioned (demolition and dismantlement), be

sure to follow the rules below.



NEVER pour waste or oil directly onto the ground, down

a drain or into any water source.



Contact your country’s Department of

Public Works or a recycling agency in your

area and arrange for proper disposal of

any electrical components, waste or oil

associated with this equipment.



When the life cycle of this equipment is over, remove

the battery (if equipped) and bring to an appropriate

facility for lead reclamation. Use safety precautions when

handling batteries that contain sulfuric acid.

When the life cycle of this equipment is over, it is

recommended that the mixer frame and all other metal

parts be sent to a recycling center.

Metal recycling involves the collection of metal from

discarded products and its transformation into raw

materials to use in manufacturing new products.

Recyclers and manufacturers alike promote the process

of recycling metal. Using a metal recycling center

promotes energy cost savings.

EMISSIONS INFORMATION

NOTICE

The gasoline engine used in this equipment has been

designed to reduce harmful levels of carbon monoxide

(CO), hydrocarbons (HC) and nitrogen oxides (NOx)

contained in gasoline exhaust emissions.

This engine has been certiﬁed to meet US EPA evaporative

emissions requirements in the installed conﬁguration.

Attempts to modify or make adjustments to the engine

emission system by unauthorized personnel without proper

training could damage the equipment or create an unsafe

condition.

Additionally, modifying the fuel system may adversely affect

evaporative emissions, resulting in ﬁnes or other penalties.

Emission Control Label

The emission control label is an integral part of the emission

system and is strictly controlled by regulation(s).

The label must remain with the engine for its entire life.

If a replacement emission label is needed, please contact

your authorized engine distributor.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MULTIQUIP Baumaschinen Handbücher

MULTIQUIP

MULTIQUIP LD6 Bedienungsanleitung

MULTIQUIP

MULTIQUIP Mikasa Series Leitfaden

MULTIQUIP

MULTIQUIP Stow MS-63 Leitfaden

MULTIQUIP

MULTIQUIP Whiteman WM45H Leitfaden

MULTIQUIP

MULTIQUIP Mikasa MVH208DZ Bedienungsanleitung

MULTIQUIP

MULTIQUIP P54K-K2B-K4B Bedienungsanleitung

MULTIQUIP

MULTIQUIP EM90SH8 Bedienungsanleitung

MULTIQUIP

MULTIQUIP MC94PH8 Leitfaden

MULTIQUIP

MULTIQUIP Stow MS-93 Leitfaden

MULTIQUIP

MULTIQUIP Whiteman Series Bedienungsanleitung

MULTIQUIP

MULTIQUIP WBH-16F Leitfaden

MULTIQUIP

MULTIQUIP Mikasa Series Leitfaden

MULTIQUIP

MULTIQUIP Mikasa MRH800GS Leitfaden

MULTIQUIP

MULTIQUIP Mikasa Series Leitfaden

MULTIQUIP

MULTIQUIP Mikasa Series Bedienungsanleitung

MULTIQUIP

MULTIQUIP Mikasa Series Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman WM120PH Series Leitfaden

MULTIQUIP

MULTIQUIP AR13H Bedienungsanleitung

MULTIQUIP

MULTIQUIP WM90SE Bedienungsanleitung

MULTIQUIP

MULTIQUIP Mikasa Series Bedienungsanleitung

MULTIQUIP

MULTIQUIP Mikasa Series Bedienungsanleitung

MULTIQUIP

MULTIQUIP Mikasa MVH408DE Bedienungsanleitung

MULTIQUIP

MULTIQUIP Mikasa Series Bedienungsanleitung

MULTIQUIP

MULTIQUIP ESSICK EM70SLF Bedienungsanleitung

Beliebte Baumaschinen Handbücher anderer Marken

SASFORKS

SASFORKS EXTREME Bedienungsanleitung

Hailo

Hailo H-50 Bedienungsanleitung

Graco

Graco LineLazer ES 1000 Gebrauchs- und Pflegehandbuch

Greenlee

Greenlee 555RSC Bedienungsanleitung

Manitowoc

Manitowoc Grove CD3340B Bedienungsanleitung

Lux Tools

Lux Tools A-FMR-20 Set Bedienungsanleitung

SIP

SIP 03683 Bedienungsanleitung

Volvo

Volvo L30G Bedienungsanleitung

Grizzly

Grizzly G8712 Bedienungsanleitung

Modulift

Modulift CMOD 12 Bedienungsanleitung

Case

Case DV201 Bedienungsanleitung

Sealey

Sealey SC10.V2 Bedienungsanleitung

Wacker Neuson

Wacker Neuson DT05 Bedienungsanleitung

HYVA

HYVA AMCO VEBA 81 Series Bedienungsanleitung

Atlas Copco

Atlas Copco Dynapac V5100TV Bedienungsanleitung

Toro

Toro 323 Bedienungsanleitung

Manitowoc

Manitowoc National Crane 1400A Bedienungsanleitung

SGS

SGS EC1500 Bedienungsanleitung