MULTIQUIP GA-6HA Anleitung zur Verwendung
The following instructions are intended to assist the
user in starting the GA-6HA AC Generator. Please read
the entire instructions before starting.
GA-6HA AC Generator
Starting Instructions
Engine Oil Check
1. To check the engine oil level, place the generator on
secure level ground with the engine stopped.
2. Remove the filler cap/dipstick from the engine oil filler
hole and wipe it clean.
3. Insert and remove the dipstick without screwing it into
the filler neck. Check the oil level shown on the
dipstick.
4. If the oil level is low (Figure 1), fill to the edge of the
oil filler hole with the recommended oil type (Table 1).
Maximum oil capacity is 1.16 quarts (1.1 liters).
edarGliOrotoM.1elbaT
erutarepmeTronosaeS liorotomfoedarG
)ssalcSMnahtrehgih(
nmutuAroremmuS,gnirpS
F°51+otF°021+ 03EAS
retniW
F°5
1+otF°04+ 03EAS
F°51+woleB03-W01EAS
Figure 1. Engine Oil Dipstick (Oil Level)
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
Explosive Fuel Hazards
WARNINGWARNING
WARNINGWARNING
WARNING
Fuel Check
1. Close the fuel cock before filling the fuel tank.
2. Remove the fuel cap located on top of fuel tank.
3. Read thefuelgauge locatedon topofthe fueltank (Figure
2) to determine if the fuel level is low. If fuel is low,
replenish with
clean unleaded fuel
.
4. When refueling, be sure to use a strainer for filtration.
DO NOT top-off fuel. DO NOT fill the tank beyond
capacity. Wipe up any spilled fuel
immediately!
Figure 2. Fuel Gauge
Before Starting the Engine
1. Be sure to
disconnect all electrical loads
from the
generator prior to starting the engine.
2. NEVER start the engine with the main
circuit breaker
in the ON position. Always place the main circuit
breaker (Figure 3) in the OFF position before starting.
Figure 4. Engine Fuel Valve Lever
Starting the Engine
1. Place the engine
fuel valve lever
(Figure 4) to the ON
position.
Figure 3. Main Circuit Breaker (OFF)
All manuals and user guides at all-guides.com
all-guides.com
© COPYRIGHT 2005, MULTIQUIP INC.
Montreal, Canada • Manchester, UK
Rio De Janeiro, Brazil • Cipsa, Mexico
MULTIQUIP INC.
POST OFFICE BOX 6254 • CARSON, CA 90749
310-537-3700 • 800-421-1244 • FAX:310-537-3927
Figure 5. Choke Lever
5. Grasp the starter grip (Figure 7) and slowly pull it out.
The resistance becomes the hardest at a certain
position, corresponding to the compression point. Pull
the starter grip briskly and smoothly for starting.
Figure 7. Starter Grip
2. Place the
choke lever
(Figure 5) in the
CLOSED
position if starting a
cold
engine.
3. Place the
choke lever
(Figure 5) in the
OPEN
position
if starting a
warm engine
or the
temperature is
warm.
4. Place the
generator ON/OFF
switch
(Figure 6) in the
ON
position.
Figure 6. Generator On/Off Switch
6. If the engine has started, slowly return the choke lever
(Figure 5) to the
OPEN
position. If the engine has not
started, repeat steps 1 through 5.
7. Before the generator is placed into operation, run the
engine for 3-5 minutes. Check for abnormal smells,
fuel leaks, and noises that would associate with loose
components.
Figure 8. Idle Control Switch
Connecting the Load
1. Place the full power switch (Figure 9) in the 120V or
240/120V position depending on application.
Figure 9. Power Switch
2. If small wattage power tools are required, connect
them to the 60 Hz output receptacles at this time.
Stopping the Engine
1. Place the main circuit breaker (Figure 3) in the OFF
position.
2. Place the
idle control switch
(Figure 8) in the OFF
position.
3. Let the engine run at idle with no load for 2-3 minutes.
4. To shut down the engine, place the generator ON/OFF
switch (Figure 6) in the OFF position.
5. Place the engine
fuel valve lever
(Figure 4) to the
"OFF" position.
6. Remove the
load
from the generator.
8.
Place
the
idle control switch
(Figure 8) in the ON
(up) position.
Figure 10. Main Circuit Breaker (ON)
3. Place main circuit breaker (Figure 10) in the ON
position.
All manuals and user guides at all-guides.com
Andere Handbücher für GA-6HA
1
Andere MULTIQUIP Tragbarer Generator Handbücher
MULTIQUIP
MULTIQUIP GA36HR Bedienungsanleitung
MULTIQUIP
MULTIQUIP Power WHISPERWATT DCA-40SSI Bedienungsanleitung
MULTIQUIP
MULTIQUIP EGS1800C3H Bedienungsanleitung
MULTIQUIP
MULTIQUIP Power WHISPERWATT DCA-150SSJU3 Leitfaden
MULTIQUIP
MULTIQUIP MQ Power Whisperwatt DCA220SSCU Leitfaden
MULTIQUIP
MULTIQUIP GA6HZR Bedienungsanleitung
MULTIQUIP
MULTIQUIP LT6KV Bedienungsanleitung
MULTIQUIP
MULTIQUIP WhisperWatt DCA150SSI Bedienungsanleitung
MULTIQUIP
MULTIQUIP ULTRA-SILENT DCA-125USJ Leitfaden
MULTIQUIP
MULTIQUIP GA-9.7 HZ Bedienungsanleitung
MULTIQUIP
MULTIQUIP GA6HB Bedienungsanleitung
MULTIQUIP
MULTIQUIP Whisperwatt DCA150SSJU4F Leitfaden
MULTIQUIP
MULTIQUIP GA-Series Bedienungsanleitung
MULTIQUIP
MULTIQUIP DA7000 Series Handbuch
MULTIQUIP
MULTIQUIP WHISPERWATT DCA10SPX4 Leitfaden
MULTIQUIP
MULTIQUIP Power Ultra-Silent DCA-70SSIU Leitfaden
MULTIQUIP
MULTIQUIP MQ POWER SG1400C4F Bedienungsanleitung
MULTIQUIP
MULTIQUIP GA-3.6RZ2 Bedienungsanleitung
MULTIQUIP
MULTIQUIP GA4.5RA Leitfaden
MULTIQUIP
MULTIQUIP DA7000SSA2GH Leitfaden
