MuxLab 500072 Bedienungsanleitung

USB 2.0 4-Port Extender Kit

Installation Guide

500072

USB 2.0 4-Port Extender Kit Installation Guide

Table of Contents

1. Introduction...............................................................................................................................2

2. Features.....................................................................................................................................2

3. Specifications............................................................................................................................2

4. Package Contents......................................................................................................................3

5. Physical Diagram......................................................................................................................3

6. Installation.................................................................................................................................5

7. Category cable wiring...............................................................................................................6

8. Troubleshooting........................................................................................................................7

9. Regulatory Compliance ............................................................................................................8

1. Introduction

The USB 2.0 high speed extender system enables USB 2.0 connectivity over Cat5e/6 at data

rates up to 480Mbps and extends true USB up to 100m (328ft) over standard Cat5 twisted pair

cable.

This unit is true plug and play, requires no additional software drivers, and is compatible with all

major operating systems such as Windows, Mac and Linux.

It is ideal for accessing remotely laser printers, scanners, web cameras, external hard drives,

CD/DVD burners, and flash drives. It supports a wide variety of USB extension applications

including security, industrial control, digital signage, scientific data acquisition and other

implementations of USB standards.

2. Features

True plug and play, no driver installation required.

Extends USB 2.0 high-speed and USB 1.1 (low-speed, full-speed) devices up to 100m

(328ft) over Cat. 5e/6 cable

Supports all USB device types: Control, Interrupt, Bulk and Isochronous at up to 480Mbps

Ideal for a wide variety of USB devices, printers, scanners, hard drives, audio devices,

touch screens, web cams, and game controllers.

Compatible with major operating systems: Windows 2000 / XP / Vista / 7 / 8 / 8.1, Mac OS,

Linux or higher

Aluminum enclosure and wall mountable

3. Specifications

Model No.

500072

Transmitter

Receiver

Chip

ICRON

Connector

Upstream / Input

USB B Female

RJ-45 Female

Output / Downstream RJ-45 Female USB Type A Female x 4

Interconnection Cable

Standard Cat. 5e/6

Max. Cable Length

100m (328ft)

LED

USB Cable Length

0.6m (USB Type A/M to Type B/M)

Power Supply

5VDC 1A

5VDC 2A

Housing

Aluminum

Dimension ( L x W x H )

90 x 73 x 31mm

USB 2.0 4-Port Extender Kit Installation Guide

4. Package Contents

1 Transmitter unit

1 Receiver unit

2 5VDC Power adapters

1 USB 2.0 Type A/M to Type B/M Cable 0.6m

5. Physical Diagram

5.1 Transmitter (Local Unit)

Top View

USB2.0 4-Port Extender

Transmitter (Host Side)

Front view

RJ45 Link

RJ45 Link port to

connect to the Cat.5

cabling

Side view

Link Led indicates a

valid link between the

Tx and the Rx via Cat.5

cabling

Link Power

Act

Power Led indicates

that the power is

connected

Act Led indicates activity when data is

transmitted between the Tx and the Rx

Rear view

Power port connects to

the 5VDC-1A power

supply

Host

5VDC-1A

Host Port is using USB

Type B interface

USB 2.0 4-Port Extender Kit Installation Guide

5.2 Receiver (Remote Unit)

Top View

Receiver (Device Side)

USB2.0 4-Port Extender

Front view

RJ45 Link port to

connect to the Cat.5

cabling

Power port connects to

the 5VDC-2A power

supply

Side view

Link Led indicates a

valid link between the

Tx and the Rx via Cat.5

cabling

Link Power

Act

Power Led indicates

that the power is

connected

Act Led indicates activity when data is

transmitted between the Tx and the Rx

Rear view

4321

Ports 1 to 4 are USB

Device Ports using

USB Type A interface.

USB 2.0 4-Port Extender Kit Installation Guide

6. Installation

6.1 Typical Application

USB Cable USB Cable

Cat.5 cable

Up to 100m

USB Cable

USB Devices

500072

Transmitter

500072

Receiver

6.2 Installing the Transmitter and the Receiver

6.2.1. Preparing for Installation

Follow these steps to prepare your installation:

1. Determine where the host computer will be located and set up the computer.

2. Determine where you want to locate the remote USB device(s).

3. The extender supports a maximum distance or 328 ft (100m). Make sure that Cat5

cabling is installed, with Cat. 5 outlets located near both computer and USB devices.

The total length of this cable, including patch cords, must not be longer than 328 ft

(100m).

6.2.2. Installing the Transmitter (Local Unit)

1. Plug the supplied USB cable into the transmitter and connect to an available USB port

of computer.

2. Plug the 5VDC, 1A power adapter into the transmitter, and AC plug into the power

outlet.

3. The Red Power LED indicator lights on.

4. Plug one end of the Cat. 5 cable into the Link port (RJ-45) on the transmitter. (Please

see Category cable wiring).

USB 2.0 4-Port Extender Kit Installation Guide

6.2.3. Installing the Receiver (Remote Unit)

1. Plug the other end of the Cat. 5 cable into the Link port (RJ-45) on the receiver.

2. Plug the 5VDC, 2A power adapter into the receiver, and AC plug into the power

receptacle.

Note: Make sure to plug the 5VDC 2A power adapter on the receiver side.

3. The Red Power LED indicator lights on.

4. Connect the USB devices through USB cables into the Receiver’s USB ports labeled 1

to 4 on receiver.

LED

Status

Definition

Color

Power

Red

Indicates that the 5VDC power adapter is plugged in.

Activity Green

Indicates that both the transmitter and the receiver are

powered on and the Cat5 cable is connected properly.

Link

Orange

Indicates that the USB ports are plugged in.

6.3 Checking the Installation

1. Check the Activity (Green) and Link (Orange) LED indicators light on both the

transmitter and the receiver.

2. For Windows users (2000, XP, Vista, 7, 8, and 8.1), open Device Manager to confirm

the extender has been installed correctly. Expand the Entry and check the USB

controllers. If the extender is installed correctly, it should be listed as a “Generic USB

Hub.”

3. For Mac OS X users, open the System Profiler to confirm that the extender has been

installed correctly. In the left column under Hardware, select “USB” and check the right

panel. If the extender has been installed correctly, you should find it listed as a “Hub”

under the USB High-Speed Bus/USB Bus.

4. If the extender is not detected correctly or fails to detect, go to the Troubleshooting

section of this manual.

7. Category cable wiring

Take precaution selecting the Cat. 5 wires

before connecting; use a cable tester to check

the wires are correctly terminated. (Incorrect

Termination may cause damage to the

receiver unit). Recommend to use T568B

wiring as shown.

USB 2.0 4-Port Extender Kit Installation Guide

8. Troubleshooting

The following table describes some of the symptoms, probable causes and possible solutions in

respect to the installation of the USB 2.0 4-Port Extender kit.

Table -1 Troubleshooting tips

Problem

Cause

Solution

The USB device is

attached but not

functioning.

• The USB device requires

drivers that were not

installed.

• The USB device does not

support USB hubs.

• The USB device might be

failed.

1. Install the required USB device driver on the

computer operating system before plug in the

USB device to the receiver. Access your USB

device’s manufacturer’s Web site for detail info.

2. In the Universal Serial Bus (USB) controllers

section of Device Manager, check if the USB

device is listed.

The USB device is

attached but not

functioning.

• An over current condition

has occurred because

the USB device is

drawing more than

500mA (USB spec.).

The operating systems

may pop up to indicate

an issue.

1. Unplug the power adapter from the receiver,

wait approximately 30 seconds; plug the power

adapter into receiver again.

2. If over current keeps occurring, either the USB

device may use more power than the USB

specification, or the USB device may be

damaged.

3. Consult your USB device documentation and

plug into your USB device with the required

power adapter.

Activity LED on

transmitter or receiver

blinks intermittently.

• The Cat. 5 cable

connecting the

transmitter and receiver

is faulty.

1. Make sure the Cat.5 cable is good.

2. Try to use a different Cat.5 cable to connect

transmitter and receiver.

Activity LED on

transmitter or receiver

is off.

• The receiver is not

powered.

• The transmitter is not

powered.

• The link cable failed or is

damaged.

• The extender is not

working.

1. Confirm that the host PC is on and providing

power to the transmitter.

2. Make sure the supplied AC power adapters are

properly connected to the transmitter or receiver.

3. Make sure the Cat5 cabling between transmitter

and receiver is properly installed or replace the

link cable.

4. Check that the power adapter is connected and

working.

If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at

877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).

USB 2.0 4-Port Extender Kit Installation Guide

Regulatory Compliance

Disclaimer

Information in this document is subject to change without notice. The manufacturer does not make any

representations or warranties (implied or otherwise) regarding the accuracy and completeness of this

document and shall in no event be liable for any loss of profit or any other commercial damage, including

but not limited to special, incidental, consequential, or other damages.

No part of this document may be reproduced or transmitted in any form by any means, electronic or

mechanical, including photocopying, recording or information recording and retrieval systems without the

express written permission of the manufacturer.

All brand names and product names used in this document are trademarks, or registered trademarks of

their respective holders.

8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5

Tel: (514) 905-0588 Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: videoease@muxlab.com URL: www.muxlab.com

Inhaltsverzeichnis

Andere MuxLab Extender Handbücher

MuxLab

MuxLab VideoEase Bedienungsanleitung

MuxLab

MuxLab 500753 Bedienungsanleitung

MuxLab

MuxLab 500451-PoE Bedienungsanleitung

MuxLab

MuxLab 500451 Bedienungsanleitung

MuxLab

MuxLab 500460-RX Bedienungsanleitung

MuxLab

MuxLab 500730 Bedienungsanleitung

MuxLab

MuxLab 500070 Bedienungsanleitung

MuxLab

MuxLab ProDigital 500485 Bedienungsanleitung

MuxLab

MuxLab 500850 Bedienungsanleitung

MuxLab

MuxLab VideoEase MonoPro XLR Benutzerhandbuch

MuxLab

MuxLab 500401-WP-US Bedienungsanleitung

MuxLab

MuxLab 500459 Bedienungsanleitung

MuxLab

MuxLab 500759-TX Bedienungsanleitung

MuxLab

MuxLab 500451-TX Bedienungsanleitung

MuxLab

MuxLab 100518 Bedienungsanleitung

MuxLab

MuxLab 500464-V2 Bedienungsanleitung

MuxLab

MuxLab DomoStream Bedienungsanleitung

MuxLab

MuxLab 500459-100 Bedienungsanleitung

MuxLab

MuxLab 500756 Bedienungsanleitung

MuxLab

MuxLab 500040 Bedienungsanleitung

MuxLab

MuxLab 100509 Bedienungsanleitung

MuxLab

MuxLab Pro Digital 500452 Bedienungsanleitung

MuxLab

MuxLab 500405 Bedienungsanleitung

MuxLab

MuxLab 500451 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung