MuxLab 500450 Bedienungsanleitung

8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5

Tel: (514) 905-0588 Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: videoease@muxlab.com URL: www.muxlab.com

Specifications

Environment

HDMI 1.3a

Devices

DVD, plasma, projectors, monitors, TV, PC, laptops, servers

supporting HDMI.

Transmission

Transparent to the user

Bandwidth

340 MHz

Signals

HDMI 1.3a protocol

Connectors

One (1) HDMI receptacle.

One (1) RJ45Sfor Cat 5e/6 unshielded or shielded twisted pair.

3.5mm jacks for IR emitter and sensor

Note: HDMI cables not included.

Maximum Distance

Based on a maximum

length of 6.6 ft (2 m)of

HDMI cable per end.

480i/p: Cat 5e/6: 330 ft (100 m)

720p, 1080i: Cat 5e/6: 330 ft (100 m)

1080p: Cat 5e/6: 330 ft (100 m)

1080p Deep Color: Cat 5e/6: 330 ft (100 m)

Note:When installed in an electrically noisy environment, an STP

cable must be used. Also, cross-connection reduces the effective

distance depending on the grade of twisted cable used.

RJ45 Pin

Configuration

Reverse Polarity

Sensitive. Use EIA/TIA

568A or 586B straight-

through wiring.

RJ45 Link

Pin 1 (R) Pin 2 (T)

Pin 3 (R) Pin 6 (T)

Pin 4 (R) Pin 5 (T)

Pin 7 (R) Pin 8 (T)

Cable

One (1) Cat 5e/6 or better twisted pair cables required

Power Supply

Two (2) 110-240V/5VDC power supplies with interchangeable blades

Power Consumption

Transmitter: 3.0 Watt Receiver: 5.0 Watt

Temperature

Operating: 0° to 40°C Storage: -20° to 85°C

Humidity: Up to 95% non-condensing

Enclosure

Aluminum

Dimensions

4.50” x 3.00” x 1.25” (11.4 x 7.6 x 3.2 cm)

Weight

2.6 lb (1.2 kg)

Compliance

Regulatory: FCC, CE, RoHS Flammability: 94V0

Warranty

2 years

Order Information

500450 HDMI Mono Extender Kit

HDMI Mono Extender Kit

500450

Quick Installation Guide

Overview

The HDMI Mono Extender Kit (500450) allows HDMI equipment to be connected up

to 330 ft (110 m) @ 1080p Deep Color via one (1) Cat 5e/6 unshielded twisted pair

cables in a point-to-point configuration. The kit comes with one (1) Transmitter and one

(1) Receiver as well as an IR Emitter (500998) and IR Sensor (500999) for remote

control applications.

Applications

Applications include commercial and residential AV systems, classroom projector

systems, digital signage, boardroom systems, collaborative PC systems, and medical

information systems.

Installation

1. Identify the connectors on the Transmitter and Receiver as indicated on the product

labels.

2. Verify that the distance between the HDMI Transmitter and Receiver is within

MuxLab specifications (see Specifications table).

3. To install the Transmitter:

3a. Connect the Transmitter to the HDMI video source with an HDMI compliant

cable.

3b. Connect one (1) lengths of Cat 5e/6 (or higher) grade UTP cables to

RJ45 LINK connectors on the Transmitter.

4. To install the Receiver:

4a. Connect the Receiver to the HDMI display equipment with an HDMI compliant

cable.

4b. Connect the one (1) Cat 5e/6 cables to RJ45 LINK connectors on the Receiver.

5. Connect the 5 VDC power supply to the Receiver first, and then plug the power

supply into an AC power outlet. Connect the 5 VDC power supply to the

Transmitter first, and then plug the power supply into an AC power outlet. If power

is present, the green power LED of the Transmitter and the Receiver will be ON.

Note: Power the HDMI Mono Extender Balun only after all connections are made.

6. Power the HDMI equipment and verify the image quality.

7. If infrared remote control is needed, connect the IR Sensor to the 3.5mm Stereo

Jack of the receiver and the IR Emitter to the 3.5mm Mono Jack of the Transmitter.

Note: You can differentiate the IR Sensor and the IR Emitter by looking at the

3.5 mm plug. The IR Sensor is using a Stereo Plug (3 Contacts) and the IR

Emitter a mono plug (2 Contacts).

8. Position the IR Sensor so that it is directed to the hand-held remote control. For a

clear IR signal reception, aim the hand-held remote control to the top of the IR

Sensor enclosure.

9. Position the IR Emitter as close as possible to the source’s IR Sensor (i.e. DVD

player). For a clear IR signal reception, the IR Emitter can be glued on the source’s

IR Sensor. The IR Emitter’s signal is transmitted from the side of the enclosure.

10. The following diagram shows the final configuration.

Troubleshooting

The following table describes some of the symptoms, probable causes and possible solutions

in respect to the installation of the HDMI Mono Extender Kit:

Symptom

Tx LEDs

Rx LEDs

Probable

Cause

Possible

Solutions

Power

HDMI

RJ45

Power

HDMI

RJ45

No Image

OFF

No power

•Check power

connections

No Image

OFF

UTP Cable

•Check the UTP

cables.

No Image

OFF

HDMI Cable

•Check the HDMI

Cable.

No Image

Synchronization

•Check cable length.

Flickering

Image

Synchronization

•Check cable length

•Check the HDMI

Cable Quality.

Choppy sound

Synchronization

•Check cable length

•Check the HDMI

Cable Quality.

Green or pink

hue

DDC

communication

•Cycle power of the

HDMI Extender.

•Check UTP cables

and replace.

Image flickers

when powering

up nearby

equipment

Interference

•Use STP cables

IR not

functioning

Remote control

not directed to

the IR Sensor or

IR Emitter not

directed to the

source.

•Make sure the IR

Sensor is directed

towards the remote

and the IR Emitter

to the equipment

IR not

functioning

Interference

from sunlight,

Fluorescent,

Neon or

Halogen lights

•Place the IR

equipment away for

the interfering light

IR not

functioning

OFF

Interference

from RF

radiation from

the TV

•Place the IR

equipment away for

the RF radiation

If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at

877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).

Inhaltsverzeichnis

Andere MuxLab Extender Handbücher

MuxLab

MuxLab 500114 Bedienungsanleitung

MuxLab

MuxLab 500759-TX-HLO Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500453 Bedienungsanleitung

MuxLab

MuxLab 100518 Bedienungsanleitung

MuxLab

MuxLab 500417 Bedienungsanleitung

MuxLab

MuxLab 100504 Bedienungsanleitung

MuxLab

MuxLab 500140 Bedienungsanleitung

MuxLab

MuxLab 500456 Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500759-TX-Dante Bedienungsanleitung

MuxLab

MuxLab 500456 Bedienungsanleitung

MuxLab

MuxLab Pro Digital 500452 Bedienungsanleitung

MuxLab

MuxLab 500451 Bedienungsanleitung

MuxLab

MuxLab 500759 Bedienungsanleitung

MuxLab

MuxLab 500115 Bedienungsanleitung

MuxLab

MuxLab 500465 Bedienungsanleitung

MuxLab

MuxLab 500759-TX Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500464 Bedienungsanleitung

MuxLab

MuxLab 500451-POE Bedienungsanleitung

MuxLab

MuxLab 100504 Bedienungsanleitung

MuxLab

MuxLab 500409 Bedienungsanleitung

MuxLab

MuxLab 500390 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung