MuxLab 500417 Bedienungsanleitung

8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5

Tel: (514) 905-0588 Fax: (514) 905-0589

Toll Free (North America): (877) 689-5228

E-mail: videoease

muxlab.co

URL: www.muxlab.co

Specifications

Environment HDMI 1.3a

Devices DVD, plasma, projectors, monitors, TV, PC, laptops, servers supporting

HDMI.

Transmission Transparent to the user

Bandwidth 225 MHz

Signals HDMI 1.3a protocol

Connectors One (1) HDMI receptacle.

Two (2) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.

One (1) 3.5 mm stereo jack for IR Sensor

Note: HDMI cables not included.

Maximum Distance

Based on a maximum

length of 6.6 ft (2 m) of

HDMI cable per end.

480i/p: Cat 5e: 300 ft (91 m) Cat 6: 300 ft (91 m)

720p, 1080i: Cat 5e: 300 ft (91 m) Cat 6: 300 ft (91 m)

1080p: Cat 5e: 150 ft (46 m) Cat 6: 200 ft (61 m)

1080p Deep Color: Cat 5e: 90 ft (27 m) Cat 6: 150 ft (46 m)

Note: When installed in an electrically noisy environment, an STP cable

must be used. Also, cross-connection reduces the effective distance

depending on the grade of twisted cable used.

RJ45 Pin Configuration

Reverse Polarity

Sensitive.

Use EIA/TIA 568A or

586B straight-through

wiring.

RJ45 A (HDMI A)

Pin 1 (R) Pin 2 (T)

Pin 3 (R) Pin 6 (T)

Pin 4 (R) Pin 5 (T)

Pin 7 (R) Pin 8 (T)

RJ45 B (HDMI B)

Pin 1 (R) Pin 2 (T)

Pin 3 (R) Pin 6 (T)

Pin 4 (R) Pin 5 (T)

Pin 7 (R) Pin 8 (T)

Cable Two (2) Cat 5e/6 or better twisted pair cables required

IR Remote for matrix

and source control

Pushbutton, built-in IR sensor

External IR sensor included

Wireless handheld remote ncluded

Power Supply One (1) 110-240V/12VDC power supplies with interchangeable blades

Power Consumption 3.6 Watt

Temperature Operating: 0° to 40°C Storage: -20° to 85°C

Humidity: Up to 95% non-condensing

Enclosure Fire retardant plastic

Dimensions 4.50” x 3.00” x 1.25” (11.4 x 7.6 x 3.2 cm)

Weight 1.0 lb (0.45 kg)

Compliance Regulatory: FCC, CE, RoHS Flammability: 94V0

Warranty 2 years

Order Information 500417 HDMI IR/Receiver with Source Control

HDMI IR/Extender with Source Control

500417

Quick Installation Guide

Overview

The HDMI IR/Extender with Source Control (500417) allows HDMI equipment to be

connected up to 150 ft (46 m) @ 1080p Deep Color via two (2) Cat 6 unshielded twisted

pair cables in a point-to-point configuration. The HDMI IR/Extender with Source

Control is used with the HDMI 4X4 Matrix Switch (500415).

Applications

Applications include commercial and residential AV systems, classroom projector

systems, digital signage, boardroom systems, collaborative PC systems, and medical

information systems.

Installation

1. Identify the connectors on the Receiver as indicated on the product labels.

All manuals and user guides at all-guides.com

2. Verify that the distance between the HDMI Receiver and the HDMI Matrix is

within MuxLab specifications (see Specifications table).

3. To install the Receiver:

3a. Connect the Receiver to the HDMI display equipment with an HDMI compliant

cable.

3b. Connect the two (2) Cat 5e/6 cables to HDMI LINK A and HDMI LINK B

connectors on the Receiver.

Note: Verify that the cables are connected straight-through (i.e., HDMI LINK A to

HDMI LINK A and HDMI LINK B to HDMI LINK B) and not inverted.

4. Connect the 12 VDC power supply to the Receiver first, and then plug the power

supply into an AC power outlet. If power is present, the green power LED of the

Receiver will be ON.

Note: Power the HDMI IR/Extender Balun only after all connections are made.

5. Power the HDMI equipment and verify the image quality.

6. If infrared remote sensor is needed, connect the IR Sensor to the 3.5mm Stereo

Jack of the receiver.

Note: The external sensor will disable the internal sensor of the product when

connected.

7. Position the IR Sensor so that it is directed to the hand-held remote control. For a

clear IR signal reception, aim the hand-held remote control at the top of the IR

Sensor enclosure.

8. The push button may also be used to manually select one of the four sources; one

of the four LEDs will light up to indicate which source has been selected.

9. The user can control the HDMI Matrix and the source using the internal or external

IR Sensor of the receiver.

10. The following diagram shows the final configuration.

Troubleshooting

The following table describes some of the symptoms, probable causes and possible

solutions in respect to the installation of the HDMI IR/Extender with Source Control:

Tx LED Rx LED

Symptom PowerSyncPowerSync

Probable

Cause

Possible

Solutions

No Image OFF OFF OFF OFF No power • Check power

connections

No Image OFF OFF ON OFF Source not

power on

• Power on source and

check the HDMI

cable of the source.

No Image ON OFF ON OFF Cable • Check the UTP cables

pin-out.

• Verify that the UTP

cables are not crossed.

No Image ON ON ON OFF Synchronization • Check cable length.

• Check source

resolution versus

distance.

Flickering Image ON ON ON ON Synchronization • Check cable length

Choppy sound ON ON ON ON Synchronization • Check cable length

Green or pink hue ON ON ON ON DDC

communication

• Cycle power of the

HDMI Extender.

• Check UTP cables

and replace.

Image flickers when

powering up nearby

equipment

ON ON ON ON Interference • Use STP cables

IR not functioning ON ON ON ON Remote control

not directed to

the IR Sensor or

IR Emitter not

directed to the

source.

• Make sure the IR

Sensor is directed

towards the remote

and the IR Emitter to

the equipment

IR not functioning ON ON ON ON Interference

from sunlight,

Fluorescent,

Neon or

Halogen lights

• Place the IR

equipment away for

the interfering light

IR not functioning ON ON ON ON Interference

from RF

radiation from

the TV

• Place the IR

equipment away for

the RF radiation

If you still cannot diagnose the problem, please call MuxLab Customer Technical

Support at 877-689-5228 (toll-free in North America) or (+1) 514-905-0588

(International).

All manuals and user guides at all-guides.com

Andere MuxLab Extender Handbücher

MuxLab

MuxLab 500459-100 Bedienungsanleitung

MuxLab

MuxLab VideoEase MonoPro XLR Benutzerhandbuch

MuxLab

MuxLab 500456 Bedienungsanleitung

MuxLab

MuxLab VGA Balun II Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab VideoEase 500090 Bedienungsanleitung

MuxLab

MuxLab 500733 Bedienungsanleitung

MuxLab

MuxLab 500086 Bedienungsanleitung

MuxLab

MuxLab 500462 Bedienungsanleitung

MuxLab

MuxLab 100504 Bedienungsanleitung

MuxLab

MuxLab 500041-WP-US Bedienungsanleitung

MuxLab

MuxLab 500756 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500465 Bedienungsanleitung

MuxLab

MuxLab 500040 Bedienungsanleitung

MuxLab

MuxLab 500752 Bedienungsanleitung

MuxLab

MuxLab 500405 Bedienungsanleitung

MuxLab

MuxLab 500753 Bedienungsanleitung

MuxLab

MuxLab 500462 Bedienungsanleitung

MuxLab

MuxLab 500454 Bedienungsanleitung

MuxLab

MuxLab 500041-WP-UK Bedienungsanleitung

MuxLab

MuxLab 500456 Bedienungsanleitung

MuxLab

MuxLab 500464-V2 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung