Nabco Gyro Tech Acuvision Bedienungsanleitung

S82 W18717 Gemini Drive

PO Box 906

Muskego, WI 53150

Phone: (877) 622-2694

Fax: (888) 679-3319

www.NabcoEntrances.com

P/N 15-10848-01

Revision 05-11-10

WARNING

Do not install, operate or service this product unless you have read and understood the Safety Practices,

Warnings, Installation and Operating Instructions contained in this manual. Failure to do so may result in

property damage or bodily injury.

Acuvision

Instruction Manual

WARNING

Turn OFF all power to the Automatic Door if a Safety System is not working.

Instruct the Owner to keep all power turned OFF until corrective action can be achieved by a NABCO

trained technician. Failure to follow these practices may result in serious consequences.

NEVER leave a Door operating without all Safety detection systems operational.

Page 2 www.NabcoEntrances.com 05-11-10

Acuvision Instruction Manual

Contents

A. Overview.................................................................................................................................................... 3

B. Specifications ............................................................................................................................................ 4

C. Appearance and Dimensions .................................................................................................................... 5

D. Installation and Adjustments

D.1 Installation .................................................................................................................................... 6

D.2 Wiring ........................................................................................................................................... 7

D.2.1 General Wiring Information ......................................................................................... 7

D.2.2 Wiring - Sliding Door with U Series Control ................................................................ 8

D.2.3 Wiring - Non-swing side of swing dr. or non-fold side of fold dr. w/ U Series Control 8

D.2.4 Wiring - Non-swing side of swing door with Magnum Control .................................... 9

D.2.5 Wiring - Swing Side of Swing Doors w/Analog Control................................................ 9

D.2.6 Wiring - Swing Side of Swing/Folding Door w/Microprocessor Control ..................... 10

D.2.7 Wiring - Swing Side of Swing Door w/Magnum Control............................................. 10

D.3 Turning ON the power ................................................................................................................ 11

D.4 Customized Settings

D.4.1) Setting up for depth coverage................................................................................... 11

D.4.2) Non-detection zone ................................................................................................... 12

D.4.3) Minute adjustment of depth coverage....................................................................... 13

D.4.4) Adjusting for Width Coverage ................................................................................... 13

D.4.5) Setting Width coverage ............................................................................................. 14

D.4.6) Operation Mode Set Up

D.4.6.1) Mutual Interference Prevention Setting ............................................. 15

D.4.6.2) Activation Signal Setting..................................................................... 16

D.4.6.3) Sensitivity setting................................................................................ 16

D.4.6.4) Standstill memory time ....................................................................... 16

D.4.6.5) Door Mode setting ............................................................................. 17

D.4.6.6) Output Time Delay.............................................................................. 17

D.5 Output (LED Indicator) ............................................................................................................... 18

D.6 Usage Tips ................................................................................................................................. 18

D.6.1) Door Panel Detection ................................................................................................ 18

D.6.2) Unplug the sensor first before changing settings...................................................... 19

D.6.3) Power consumption................................................................................................... 19

D.6.4) Exterior Interference.................................................................................................. 19

D.6.5) Moving items ............................................................................................................. 19

D.6.6) Removable items in detection area........................................................................... 19

D.6.7) Sensors close together ............................................................................................. 19

D.6.8) Reflected light ........................................................................................................... 19

D.6.9) Precipitation interference .......................................................................................... 19

D.6.10) Changes in background conditions......................................................................... 19

D.7 Troubleshooting.......................................................................................................................... 20

D.7.1) Sensor symptoms and how to solve them ................................................................ 20

D.7.2) Sensor symptoms using wrong Door Mode settings ................................................ 20

E. NABCO ENTRANCES Return Policy ...................................................................................................... 21

Page 3 www.NabcoEntrances.com 05-11-10

Acuvision Instruction Manual

CAUTION

The purpose of this manual is to familiarize the purchaser with the proper installation and operation of this

system. It is essential that this equipment be properly installed and operational before the door is used by

the public. It is your responsibility to inspect the operation of the entrance system to be sure it complies

with any applicable standards. In the United States, ANSI Standard 156.10 and 156.19 usually cover the

operation of the doors.

Instruct the building owners/operator on the essentials of the operation of the door and this device. The

owner should follow these instructions to determine whether the door is operating properly and should

immediately call for service if there is any malfunction.

All installation changes and adjustments must be made by qualified, NABCO trained technicians.

A. Overview

On swing and folding doors, the Acuvision has been designed to provide swing side presence

detection coverage similar to the coverage currently supplied by the swing side Acusensor 1B. It

also provides additional protection by scanning into the threshold area of the door.

The Acuvision will memorize the door swing area and door position during the first activation

cycle. During the door cycle, the Acuvision will also scan the threshold area and store this

information into its memory.

On sliding doors, the Acuvision has been designed to provide simultaneous motion and thresh-

old coverage during the complete door cycle. It provides additional threshold protection by

scanning backward into the visible area of the threshold of the door at full open as well as

threshold re-activation protection during the closing cycle.

Reminder! No encoder signals are necessary!

The Acuvision memorizes the area backward into the threshold using

unique infrared learning technology.

The Acuvision can be used on new, or retro-fitted to, existing Slide, Swing and Folding doors.

The output signals provided by the Acuvision are as follows:

OUTPUT #1:

On Sliding doors, output 1 connects to the activation circuit and is used as the activation signal

including the threshold and motion area re-activation signal during the closing cycle.

On non-swing side of Swing or Folding Doors, output 1 connects to the activation circuit .

OUTPUT # 2: When the Acuvision is mounted on the swing side of a Swing or Folding door,

output 2 connects to the safety circuit and is used for the Presence signal at the fully opened/

closed position. The approach side motion detection remains active at all times.

Page 4 www.NabcoEntrances.com 05-11-10

Acuvision Instruction Manual

B. Specifications

Items Specifications

Part Description ACUVISION

Part Number # 14-10823-01

Sensing System Active reflective infrared system (Motion / Presence)

Power source 12 to 24 VAC or DC Note: Use “Class2” Power Supply

Current consumption 80mA Max. (at 12 VDC), 3 VA Max. (at 24 VAC)

Output Contacts Rating

30VAC/50VDC 0.1A Max. (Resistance load)

[Semiconductor Relay]

No Detection: “OPEN”, Detection: “CLOSED”,

Power failure: “OPEN”

30VAC/50VDC 0.1A Max. (Resistance load)

[Semiconductor Relay]

No Detection: “OPEN”, Detection: “CLOSED”,

Power failure: “OPEN”

Mounting height Max. 118” above detection area

Detection area

(when mounted at a

height of 118”)

118” (3000mm) Width x 78” (2000mm) Depth Max

Five position adjustment lever is available.

10”(250mm) depth as threshold protection

Area minute adjustment -4 to +4 degrees, at intervals of 1 degree

Output display

Waiting: ...............................Green LED Lit

Safety Detection: .................Amber LED Lit

Activation Detection:............Red LED Lit

Sensor malfunction:.............Respective LED Light Blinks

Standstill memory time

(learn time)

0 sec (Motion), 2 sec, 5 sec, 15 sec, 30sec,

90 sec, 300 sec and Forever detection (∞)

Output holding time 0.5 seconds/2.0s/4.5s/8.0s

Weight Approximately 1/2 lb.

Color Black

Page 5 www.NabcoEntrances.com 05-11-10

Acuvision Instruction Manual

C. Appearance and Dimensions

Figure 1 - Appearance

8.66” (220mm)

Mounting Pitch 7.87” (200mm)

1.34” (34mm)

3.0” (76mm)

Sensor is interchangeable with Acusensors and Acumotion

8 pin Connector

Dip. Switches 1-8

Depth Adjustment Lever

Area Minute Adjustment Knob

Dip. Switches 9-16

Page 6 www.NabcoEntrances.com 05-11-10

Acuvision Instruction Manual

D. Installation and Adjustments

D.1 Installation

The Acuvision is designed to be installed on an entranceway header or other similar mounting

surface using screws provided with the unit. A drill template is provided to assist in locating and

drilling the mounting holes and the hole for the wiring.

The Acuvision is designed to detect the area including the door panels directly below the

mounting surface. If the mounting surface is not vertical or if it is necessary to move the

detection area in or out from the door (refer to page 13), small shims can be used to make the

necessary adjustments. The unit must be mounted such that it detects the door and still

provides adequate threshold protection.

Under normal circumstances the unit will be mounted in the center of the door opening on the

entrance header and up to 118 inches above the floor. It must be mounted as close to the

bottom edge of the header as possible. The dip switches have been preset at the factory for

normal installation. These settings are:

Depth Coverage ....................................................................................... Position 4

Minute Adjustment ..................................................................................... 0 degree

Mutual Interference Prevention Mode..........................................................Mode C

Sensitivity Setting.......................................................................................Standard

New Memory Timer................................................................................30 seconds

Width Coverage ..............................................................................All seven zones

CAUTION:

To prevent electrical shock, make sure that there are no electrical wires or other products in the area close to the

place where you are going to drill.

Page 7 www.NabcoEntrances.com 05-11-10

Acuvision Instruction Manual

Note !

Because sensor “looks”

backward through the threshold

area, it must not be obstructed

by the mounting surface.

Therefore, when using sensor

on swing, fold, or sliding doors,

install no higher than 1.5”

above bottom of header as

shown at right.

Color of wire Function Notes

Brown 12VDC

24VAC Use “Class 2” Power Supply

Red GND

Black (N.O.)

OUTPUT #1 --- Activation Signal Output

30VAC/50VDC 0.1A Max.

(Resistance load)

[Semiconductor Relay]

Green (COM)

Gray (INPUT) INPUT #1 --- Fully Closed Signal Input

If there is a possibility of swing /folding doors open-

ing slightly from the fully closed position due to wind

or stack pressure, this input signal may be required

in order for the sensor to recognize when the door is

in the fully closed position. A mechanical or magnet-

ic door closed switch is necessary for this function.

This signal can be output automatically from

Microprocessor U series. (No signal required on

Sliding doors.)

A dry switch contact is required.

For swing doors use:

1 x P/N 14-11313

For folding doors use:

1 x P/N 14-11343-20

1 x P/N 14-11313-20

Yellow (INPUT)

White (N.O.) OUTPUT #2 --- Safety Signal Output

Safety Signal Output: Connected to Locked out

safety input of Control box.

Not used

30VAC/50VDC 0.1A Max.

(Resistance load)

[Semiconductor Relay]

Blue (COM)

D.2 Wiring

D.2.1) General Wiring Information

Sensor should be installed

no higher than 1.5” from

the bottom edge of header

DN0183

Page 8 www.NabcoEntrances.com 05-11-10

Acuvision Instruction Manual

D.2.2) Wiring - Sliding Door with U Series Control

Cut the (3) pin connector off of the existing Acusensor extension harness (PN # 22-9267).

Wire nut the two harnesses together as shown below. Insert the new Acuvision cable

(PN # 22-11023) into the hole in the header cover so the connector is on the exterior of the cover.

Mount the Acuvision Sensor. Note: Acuvision dipswitch Settings: (9 ON & 10 OFF)

DN0183

D.2.3) Wiring - Non-swing side of swing door or non-fold side of fold door with U Series Control

Insert new Acuvision cable (PN # 22-11023) into drilled hole in header. Cut Quick Disconnect

connector off main microprocessor harness as shown. Wire nut Acuvision harness to main harness

as shown below. Mount the Acuvision Sensor.

Note: Acuvision dipswitch Settings: (9 ON & 10 OFF)

DN0183

RED

YELLOW

GRAY

Cut

# 22-9267-00

ACUSENSOR

EXTENSION HARNESS

NOT USED

YELLOW

NOT USED

12/24 VOLTS AC/DC

ACUVISION HARNESS

RED

GRAY

BROWN

RED

GREY

YELLOW

GREEN

BLACK

BLUE

WHITE

12/24 VOLTS AC/DC

INPUT

INPUT COM

OUTPUT#1 N.O.

OUTPUT#1 COM

OUTPUT#2 N.O.

OUTPUT#2 COM

HOLE ON

THE

HEADER

COVER

RED

BLACK

BROWN

Cut

RED

BLACK

OUTPUT#1 N.O.

OUTPUT#1 COM

OUTPUT#2 COM

OUTPUT#2 N.O.

GREEN

BLACK

WHITE

BLUE

INPUT COM

INPUT

YELLOW

GREY

RED

BROWN BROWN

HOLE ON

THE

HEADER

COVER

QUICK DISCONNECT ON

MICROPROCESSOR

MAIN HARNESS

ACUVISION HARNESS

NOT USED

12/24 VOLTS AC/DC

Page 9 www.NabcoEntrances.com 05-11-10

Acuvision Instruction Manual

D.2.4) Wiring - Non-swing side of swing door with Magnum Control

Insert new Acuvision cable (PN # 22-11023) into drilled hole in header. Connect Acuvision

harness to Magnum terminal block as shown below. Mount the Acuvision Sensor.

Note: Acuvision dipswitch Settings: (9 ON & 10 OFF)

DN0183

BLACK

TERMINAL # 6

MAGNUM BOARD

TERMINAL BLOCK

CONNECTIONS

RED

ORANGE

BROWN

RED

GREY

YELLOW

BLUE

WHITE

BLACK

GREEN

INPUT

INPUT COM

OUTPUT#2 N.O.

OUTPUT#2 COM

OUTPUT#1 COM

OUTPUT#1 N.O.

HOLE ON

THE

HEADER

COVER

ACUVISION HARNESS

TERMINAL # 1

TERMINAL # 2

NOT USED

TERMINAL # 5

NOT USED

12/24 VOLTS AC/DC

24 VAC

HOLE

ON THE

HEADER

COVER

TRANSFORMER

P/N 14-2101

TO EXTERNAL

LOCKOUT MODULE

TO RED (COMMON)

OUTPUT#1 N.O.

OUTPUT#1 COM

OUTPUT#2 COM

OUTPUT#2 N.O.

INPUT COM

INPUT

BLACK

GREEN

BLUE

WHITE

YELLOW

GREY

RED

BROWN

RED WIRE ABOVE IS FOUND

ON FOUR WIRE MAT HARNESS

ON ANALOG CONTROL

ACUVISION HARNESS

DOOR CLOSED INPUT

SEE NOTE ON PG. 18

12/24 VOLTS AC/DC

NOT USED

Page 10 www.NabcoEntrances.com 05-11-10

Acuvision Instruction Manual

TERMINAL # 5

TERMINAL # 4

TERMINAL # 2

TERMINAL # 1

HOLE ON

THE

HEADER

COVER

OUTPUT#1 N.O.

OUTPUT#1 COM

OUTPUT#2 COM

OUTPUT#2 N.O.

INPUT COM

INPUT

GREEN

BLACK

WHITE

BLUE

YELLOW

GREY

RED

BROWN BROWN

ORANGE

WHITE

RED

MAGNUM BOARD

TERMINAL BLOCK

CONNECTIONS

DOOR CLOSED INPUT

SEE NOTE ON PG. 18

ACUVISION HARNESS

12/24 VOLTS AC/DC

NOT USED

BLUE

WHITE

BLACK

GREEN

OUTPUT#2 N.O.

OUTPUT#2 COM

OUTPUT#1 COM

OUTPUT#1 N.O.

ACUVISION HARNESS

QUICK DISCONNECT ON

MICROPROCESSOR

MAIN HARNESS

HOLE ON

THE

HEADER

COVER

GREEN

RED

Cut RED

GREEN

ORANGE

BROWN

RED

GREY

YELLOW

INPUT

INPUT COM DOOR CLOSED INPUT

SEE NOTE ON PG. 18

12/24 VOLTS AC/DC

NOT USED

DN0183

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nabco Zubehör Handbücher

Nabco

Nabco Acusensor M Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung