nannyVac BL Series Bedienungsanleitung
Thank you for purchasing this product. Please Read all the instructions carefully before
attempting to operate this product and save this instruction manual for future reference.
Gyro-Navigation Robot Vacuum Cleaner
Instruction Manual
This instruction manual applicable for BL series Gyro-Navigation version
CONTENTS
................................................................................
1
2-3
3
4-6
4-5
5
7-10
7
7
8
9
11
12
2-3
1. SAFETY INSTRUCTION
2. COMPONENTS
3. OPERATION INSTRUCTION
2.1 PARTS NAME
2.2 TECHNICAL PARAMETER
3.1 QUICK USER GUIDE
3.2 CLEAN/PAUSE/CHARGE/STAND-BY/TURN OFF
4. MAINTENACE
5. FAILURE CHECKING
6. ACCESSORIES LIST
4.1 CLEANING SIDE BRUSHES
4.2 CLEANING THE DUSTBIN BOX AND FILTER
4.3 CLEANING THE INFRARED SENSOR
AND CHARGING CONNETOR
.............................................................................................
..............................................................................................
...........................................................................
........................................................................
....................................................................................
..............................................
6
3.3 CLEANING MODE SELECTION
........................................................................
.................................................................................................
...........................................................................
.................................................
............................................................
4.4 INSTALLING AND USING WATER TANK...........................................................
...................................................................................
...................................................................................
104.5 REPLACEMENT OF BATTERY........................................................................
1. SAFETY INSTRUCTION
1
small repair
any let
get close the product
Always remember
Make sure
are properly
let
liquid
properly
cause
longer
have not read this
byintended
Caution
Attention
The product, mainly applicable to home, hotel rooms and small office is good for cleaning
Thin-carpet, wood floor, hard floor, ceramic tile, etc. But not suitable for high-pile carpet or
very dark-colored floors.
Applicability:
2.COMPONENTS
2.1 PARTS NAME
ON / OFF & Auto - cleaning button
Infront bumper / Mechanical bumper
Infrared sensors
Top cover
Universal wheel
Ground sensor
Charging contactor
Left side brush
Right side brush
Right wheel
HEPA Filter
Dustbin box lock
Primary Filter
Main body
2
Top cover
Dustbin box
Dustbin box handle
Charging hole
Infrared receiver window
Air outlet
Infrared Receiver
Auto - charging button
Ground sensor Ground sensor
Suction channel
Left wheel
Dustbin box
Dustbin box cover
2.COMPONENTS
Docking hole
Infrared signal emitter window
Charging electrode
Functional keys
Remote controller
Docking station / Charging base
1.Start working：related function key blue light flashing.
2.Error：2 buttons bule light flashing and with notify sound.
3.Charging：2 buttons blue light flashing.
4.Full charging: 2 buttons blue light keep lighting.
3
2.2 TECHNICAL PARAMETER
Specification Item
15W
DC 12V 1A
7.4V 2600mA Li-ion battery
2.0kg
0.6L
310*81mm
1. Turn off power & Cancell key
2. Speed selection（Normal/Slowly）
3. Forward button
4. Turn left button
5. Turn right button
6. Backward button
7. Mute button
8. Spot cleaning mode
9. Auto cleaning mode
10. Mopping mode
11. Auto - recharging button
POWER SPEED
AUTO SPOT
MOPCHARGE
Indicator light:
10
98
7 6
5
4
3
21
Power indicator light
Parameter
Product size
Weight
Dustbin capacity
Power rated
Power input
Battery specification
11
VOICE
Auto-charging
Auto-cleaning/ ON/OFF/Pause
4
3.1 QUICK USER GUIDE
1.Position the charging base
2.Two charging methods
3.OPERATION INSTRUCTION
1M
1M
2M
Install the charging base on the flat ground firmly
and against the vertical wall (fixed on the wall with
the charging base sticker).
Ensure no obstacles or hollow areas 2M away from
the charging base in front and 1M on left and right.
Connect the AC-DC adaptor with the charging hole on unit.
Control the unit return to the charging base under stand-by
or working mode. (Press the auto recharge button on remote
controller or press the charge button on unit.)
3. Auto recharge
Connected the charging station, the cleaner will auto return to
charging base when power lower than 20%.
Attention:
Please keep the charging base well connected
with power socket, otherwise, the cleaner cannot
find charging station to perform auto recharge.
*
Switch off the power switch on unit when not in use, and disconnect
with the charging.
NOTE:
1. The indicator light of operation button will flash when charging the unit. After fully charged,
the indicator light will keep lighting.
2. If the battery power too low it may caused fail to turn on the unit, Please manually to put
the unit on charging base for charging
3. Please fully charged the unit and turn off the power switch if not using the unit for a long time.
4. Store it in a dry and safety environment. Meanwhile, for avoiding battery failure, please keep to
charging the unit every 3 months.
3.OPERATION INSTRUCTION
5
2.PAUSE
4.STAND-BY
5.TURN OFF
3.CHARGE
*Attention
4.TURN ON THE UNIT
Long press the “ ” button for 3 seconds to turn on the unit, blue flashing.
*Under stand-by mode, long press the “ ” button for 3 seconds
after the sound to turn off the unit.
3.2 CLEAN/PAUSE/RECHARGE/STAND-BY/TURN OFF
A. Long press the “ ” button to turn on the unit.
B. Short press the “ ” button on unit or press “ Auto” button on Apps or remote to start working.
1. CLEAN
Pause means to switch off the unit from clean mode to stand-by mode, short press “ ” button,
the unit paused working.
A. Press “ CHARGE” button on Apps or on remote or press “ ” button on unit for charging.
B. When finish the cleaning task or battery power lower than 20%, then unit will return to
charging base for charging automatically.
If the unit is idle for 1 minute ,it will be into sleep mode, press the “ ” button to wake up the unit.
Under stand-by mode, press the “ ” on unit also can wake up it.
1.
Long press the “ ” button on unit for 3 seconds after the sound to turn off the unit.
2. Press the “ ” button on remote to turn off the power ( this button can’t turn on the power ).
3.OPERATION INSTRUCTION
2. SPOT CLEANING
6
3.3 CLEANING MODE SELECTION
Press “SPOT” button on remote controller, this mode is usually used to clean floors
where dirt is more concentrated. It will clean the area within 1m2and clean by spiral
mode automatic operate in around 2-3 minutes.
..........................................................
...............................................
Room A Room B
Room D -- next step Room C --- Cleaning
1. AUTO MODE (SMART CLEAN)
Press” Auto” on remote or “Smart Clean” on Apps. After cleaning task started, combined along with
Gyro-Sensor + SLAM technology to collect the room envrionment for analysis and calculate,
Path planned, step by step, orderly and efficiently to clean the floors in high coverage. After finish
the cleaning, the unit returnsback to origin or docking station for charging.
*
*
The Robot plans path automatically when working, if being moved, it will be rebuild the plan path
and clean again. Please DO NOT move the Robot randomly to ensure high efficiently cleaning.
After cleaning task started, the robot will stop a while to search in place and build clean path,
depends on the room’s complexity .
Attention:
3. AUTO MOP
Press “MOP” on Apps or remote to start mopping. Assembly the mop pad or mechanical water
tank onto the unit before using this mode. Under mop mode, the vacuum cleaning mode will stop
working (no suction power) and the mop route are the same as smart cleaning routes.
4. MAINTENACE
4.1 CLEANING SIDE BRUSHES
*NOTE
4.2 CLEANING THE DUSTBIN BOX AND FILTER
*NOTE
1.Take out the dustbin box and remove the HEPA filter.
2.Please gently shake the HEPA filter and clean it using the brush.
3.Clean the HEPA filter every15-30 days and replace it every 6 months.
4.Empty the dustbin box and clean it using the brush and/or wash it.
5.After having wiped all components, assemblethem being careful to insert the
Hepa filter into the housing
7
2. Please clean side brush regularly and replace it if necessary.
1. Please install the side brush at first use, align side brush and fixed shaft and then press them.
When replacing the side brush, please grasp the soft rubber and pull out.When installing, align the
square hole of the side brush with the side brush to fix the convex shaft, and press it gently to install it.
Please clean the dust box each time after working, cleaning steps as following figures.
C
C D E
A B
4. MAINTENANCE
4.3 CLEANING THE INFRARED SENSOR AND CHARGING CONNECTOR
*NOTE
8
Clean the ground detection sensors and charging electrodes
Clean the infrared sensors
Please use a dry and soft cloth to clean the infrared receiver and charging connector
as following figures.
1. Please clean the charging electrode on time to avoid charging issues.
2. Before cleaning, please make sure the power switch is turned off.
Clean the charging electrode
Clean the infrared signal emitter
Inhaltsverzeichnis
Andere nannyVac Staubsauger Handbücher
Beliebte Staubsauger Handbücher anderer Marken
Bissell
Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung
Panasonic
Panasonic MC-YL637S147-AE Bedienungsanleitung
NEFF
NEFF N17XH10 0 Series Bedienungsanleitung
LG
LG A9 Series Bedienungsanleitung
Oreck
Oreck Cordless Captura BK51700 Series Bedienungsanleitung
Kogan
Kogan KAVACROBVWA Bedienungsanleitung
