National Instruments 5741 Bedienungsanleitung

GETTING STARTED GUIDE

NI 5741

16-Channel Signal Generator

Note Before you begin, install and configure your chassis and controller.

The NI 5741 is a 16-channel, 1 MS/s analog output adapter module designed to work in

conjunction with your NI FlexRIO™ FPGA module.

The NI 5741 features 16-bit analog output channels that can be configured to drive either

unipolar or bipolar output.

This document explains how to install and connect signals for the NI 5741R, which is

composed of a FlexRIO FPGA module and the NI 5741.

Caution The protection provided by the NI 5741 can be impaired if it is used in a

manner not described in this document.

The following figure shows an example of a properly connected FlexRIO device.

Figure 1. FlexRIO Device

NI FlexRIO

Adapter Module + = NI FlexRIO Device

NI FlexRIO

FPGA Module

Contents

Electromagnetic Compatibility Guidelines...............................................................................2

How to Use Your FlexRIO Documentation.............................................................................. 2

FlexRIO Documentation Locations.................................................................................. 3

Verifying the System Requirements..........................................................................................4

Unpacking the Kit..................................................................................................................... 4

Preparing the Environment....................................................................................................... 5

Installing the Application Software and Driver........................................................................ 5

Installing the NI FlexRIO Devices............................................................................................6

Installing the NI FlexRIO Adapter Module...................................................................... 6

Connecting Cables.................................................................................................................... 7

Removing the Adapter Module.................................................................................................8

Disabling the Adapter Module in LabVIEW FPGA.........................................................8

Uninstalling the Module....................................................................................................8

Installing Accessories............................................................................................................... 8

Appendix A: NI 5741 Features................................................................................................. 9

Front Panel and Connector Pinouts...................................................................................9

Block Diagrams...............................................................................................................11

Appendix B: Interfacing with the NI 5741............................................................................. 12

Component-Level Intellectual Property (CLIP)............................................................. 12

Clocking.......................................................................................................................... 15

Where to Go Next................................................................................................................... 15

Worldwide Support and Services............................................................................................ 16

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits are designed to provide reasonable protection against harmful interference when the

product is operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any modifications to the product not expressly approved by National Instruments

could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Note To ensure the specified EMC performance, the length of all I/O cables must

be no longer than 30 m (100 ft).

How to Use Your FlexRIO Documentation

Refer to the following flowchart for information about how to use FlexRIO documentation.

2| ni.com | NI 5741 Getting Started Guide

Figure 2. How to Use Your FlexRIO Documentation

LabVIEW FPGA

Module Help

NI FlexRIO

Help

LabVIEW

Examples

INSTALL Hardware

and Software

CONNECT Signals

and LearnAbout

Your AdapterModule

LEARN About

LabVIEW FPGA

Module

PROGRAM Your

NI FlexRIO System

in LabVIEW FPGA

Module

Specifications document

for your FPGA module

Specifications document

for your adapter module

Are

You New to

LabVIEW FPGA

Module?

Yes No

Getting Started Guide

for your adapter module

Getting Started Guide

for your FPGA module

NI FlexRIO Adapter

Module Development Kit

User Manual

FlexRIO Documentation Locations

Table 1. FlexRIO Documentation Locations and Descriptions

Document Location Description

Getting started guide

for your FPGA module

Available from the Start menu and

at ni.com/manuals.

Contains installation

instructions for your FlexRIO

system.

Specifications

document for your

FPGA module

Available from the Start menu and

at ni.com/manuals.

Contains specifications for

your FPGA module.

Getting started guide

for your adapter

module

Available from the Start menu and

at ni.com/manuals.

Contains signal information,

examples, and CLIP details for

your adapter module.

Specifications

document for your

adapter module

Available from the Start menu and

at ni.com/manuals.

Contains specifications for

your adapter module.

NI 5741 Getting Started Guide | © National Instruments | 3

Table 1. FlexRIO Documentation Locations and Descriptions (Continued)

Document Location Description

LabVIEW FPGA

Module Help

Embedded in LabVIEW Help and

at ni.com/manuals.

Contains information about

the basic functionality of the

LabVIEW FPGA Module.

NI FlexRIO Help Available from the Start menu and

at ni.com/manuals.

Contains information about

the FPGA module, adapter

module, and CLIP

configuration information.

NI FlexRIO Adapter

Module Development

Kit User Manual

Available from the Start menu at

Start»All Programs»National

Instruments»NI FlexRIO»NI

FlexRIO Adapter Module

Development Kit»

Documentation.

Contains information about

how to create custom adapter

modules for use with FlexRIO

FPGA modules.

LabVIEW Examples Available in NI Example Finder. In

LabVIEW, click Help»Find

Examples»Hardware Input and

Output»FlexRIO.

Contains examples of how to

run FPGA VIs and Host VIs

on your device.

IPNet Located at ni.com/ipnet. Contains LabVIEW FPGA

functions and intellectual

property to share.

NI FlexRIO product

page

Located at ni.com/flexrio. Contains product information

and data sheets for FlexRIO

devices.

Verifying the System Requirements

To use the NI 5741, your system must meet certain requirements. For more information about

minimum system requirements, recommended system, and supported application development

environments (ADEs), refer to the readme, which is available on the software media or online

at ni.com/updates.

Unpacking the Kit

Caution To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

4| ni.com | NI 5741 Getting Started Guide

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

Preparing the Environment

Ensure that the environment you are using the NI 5741 in meets the following specifications.

............................................................................Operating temperature

(IEC 60068-2-1, IEC 60068-2-2)

0 °C to 55 °C

............................................................................Operating humidity

(IEC 60068-2-56)

10% to 90% RH, noncondensing

............................................................................Pollution Degree 2

............................................................................Maximum altitude 2,000 m at 25 °C ambient temperature

Indoor use only.

Note Refer to the NI 5741 Specifications at ni.com/manuals for complete

specifications.

Installing the Application Software and Driver

Before installing your hardware, you must install the application software and instrument

driver. Visit ni.com/info and enter rdsoftwareversion as the Info Code to determine

which minimum software versions you need for your device. Install the software in the

following order:

1. Install LabVIEW.

Refer to the LabVIEW Installation Guide for installation instructions for LabVIEW and

system requirements for the LabVIEW software. Refer to the LabVIEW Upgrade Notes

for additional information about upgrading to the most recent version of LabVIEW for

Windows. Documentation for LabVIEW is available at ni.com/manuals and by selecting

Start»All Programs»National Instruments»LabVIEW»LabVIEW Manuals.

2. Install the LabVIEW FPGA Module.

Refer to the LabVIEW FPGA Module Release and Upgrade Notes for installation

instructions and information about getting started with the LabVIEW FPGA Module.

NI 5741 Getting Started Guide | © National Instruments | 5

Documentation for the LabVIEW FPGA Module is available at ni.com/manuals and by

selecting Start»All Programs»National Instruments»LabVIEW»LabVIEW

Manuals.

3. (Optional) Install the LabVIEW Real-Time Module.

Refer to the LabVIEW Real-Time Module Release and Upgrade Notes for system

requirements, installation instructions, and additional information about using the

LabVIEW Real-Time Module.

4. Install NI FlexRIO.

Refer to the NI FlexRIO Readme on the NI FlexRIO installation media for system

requirements and installation instructions for NI FlexRIO Support. Documentation for

NI FlexRIO Support is available at ni.com/manuals and by selecting Start»All

Programs»National Instruments»NI FlexRIO.

Note If you are not using an adapter module, skip step 5.

5. Install NI FlexRIO Adapter Module Support.

Refer to the NI FlexRIO Adapter Module Support Readme on the NI FlexRIO Adapter

Module Support installation media for system requirements and installation instructions.

Documentation for NI FlexRIO Adapter Module Support is available at ni.com/manuals

and by selecting Start»All Programs»National Instruments»NI FlexRIO»NI FlexRIO

Adapter Module Documentation.

Installing the NI FlexRIO Devices

Note You must install the software before installing the hardware.

Installing the NI FlexRIO Adapter Module

Refer to the getting started guide for your FlexRIO FPGA module for FlexRIO FPGA module

installation instructions.

1. Gently insert the guide pins and the high-density card edge of the NI FlexRIO adapter

module into the corresponding connectors of the NI FlexRIO FPGA module, as shown in

the figure below.

6| ni.com | NI 5741 Getting Started Guide

Figure 3. Installing the NI FlexRIO Adapter Module

PXI-1000B

1. NI FlexRIO Adapter Module

2. Captive Screw

3. Guide Pin

4. PXI/PXI Express Chassis

5. NI FlexRIO FPGA Module

The connection may be tight, but do not force the adapter module into place.

2. Tighten the captive screws on the NI FlexRIO adapter module to secure it to the

NI FlexRIO FPGA module. NI recommends using the laser-tipped screwdriver (part

number 748677-01) included in the NI 5741 packaging.

3. Launch LabVIEW to begin configuring your NI FlexRIO system.

Connecting Cables

• Use any shielded50 Ω SMA cable to connect signals to the connectors on the front panel

of your NI 5741

• Use the SHH19-H19-AUX cable (NI part number: 152629-01 or 152629-02) to connect

to the digital I/O (DIO) and programmable function interface (PFI) signals on the AUX

I/O connector. NI recommends using the SCB-19 connector block to access the DIO and

PFI signals.

• Use the NI SHC68-C68-D4 VHDCI cable (NI part number: 196275-01) to connect to the

AO 0-15 connector.

NI 5741 Getting Started Guide | © National Instruments | 7

Removing the Adapter Module

Complete the following steps to remove the adapter module from the FlexRIO FPGA module.

Disabling the Adapter Module in LabVIEW FPGA

To properly remove an adapter module from the FlexRIO FPGA module, you must disable the

adapter module within the LabVIEW FPGA user interface. To disable the adapter module

within LabVIEW, complete the following steps.

1. In your LabVIEW Project Explorer window, right-click the IO Module item under the

FPGA Target and select Properties to display the IO Module Properties dialog box.

2. Click the Status category to view the adapter module Status dialog.

3. Deselect the checkbox for Enable IO Module Power. When this option is deselected,

firmware tristates the FlexRIO I/O and disables all adapter module power rails.

4. Click OK.

Uninstalling the Module

Caution If the module has been in use, it may exceed safe handling temperatures

and cause burns. Allow the module to cool before removing it from the chassis.

1. Disconnect any cables from the module front panel connectors.

Caution Disconnect any external clock or digital connections to the device

front panel. Applying external signals while the device is powered off may

cause damage.

2. Power off the chassis.

3. Ground yourself with a grounding strap or touch a grounded metal surface.

4. Unlatch the module by pushing down on the ejector handle.

5. Hold the module by the ejector handle and remove it from the slot.

Store the module in the original antistatic packaging when not in use to avoid damage.

Installing Accessories

The NI SMB-2152 is a breakout box accessory for debugging your NI 5741. The NI part

number for the NI SMB-2152 is 189408F-08L.

Related Information

For information about installing the NI SMB-2152, refer to the NI SMB-2152 Installation

Guide at ni.com/manuals.

8| ni.com | NI 5741 Getting Started Guide

Appendix A: NI 5741 Features

Front Panel and Connector Pinouts

The following figure shows the front panel connector and signal descriptions for the NI 5741.

Figure 4. NI 5741 Front Panel Connectors

0-15

PFI 0

AUX

I/O

1 MS/s

16-Bit

Analog Output

Caution To avoid permanent damage to the NI 5741, disconnect all signals

connected to the NI 5741 before powering down the module, and connect signals

NI 5741 Getting Started Guide | © National Instruments | 9

only after the adapter module has been powered on by the NI FlexRIO FPGA

module.

Caution Connections that exceed any of the maximum ratings of any connector on

the NI 5741 can damage the device and the chassis. NI is not liable for any damage

resulting from such connections.

Figure 5. NI 5741 Analog Output Connector Pinout

No Connect

GND

No Connect

GND

No Connect

GND

No Connect

RESERVED

No Connect

GND

No Connect

GND

No Connect

GND

No Connect

GND

AO 15

GND

AO 13

GND

AO 11

GND

AO 9

GND

AO 7

No Connect

AO 5

GND

AO 3

No Connect

AO 1

GND

No Connect

GND

No Connect

GND

No Connect

GND

No Connect

GND

No Connect

GND

No Connect

GND

No Connect

GND

No Connect

GND

No Connect

GND

AO 14

RESERVED

AO 12

GND

AO 10

GND

AO 8

GND

AO 6

RESERVED

AO 4

GND

AO 2

No Connect

AO 0

GND

No Connect

GND

Related Information

For information about the NI 5741 front panel connector specifications, refer to the NI 5741

Specifications at ni.com/manuals.

10 | ni.com | NI 5741 Getting Started Guide

Inhaltsverzeichnis

Andere National Instruments Adapter Handbücher

National Instruments

National Instruments SCXI 1346 Bedienungsanleitung

National Instruments

National Instruments NI 5791R Bedienungsanleitung

National Instruments

National Instruments 653 Series Bedienungsanleitung

National Instruments

National Instruments NI 9149 Bedienungsanleitung

National Instruments

National Instruments NI 9949 RJ-50 Bedienungsanleitung

National Instruments

National Instruments BNC-2144 Bedienungsanleitung

National Instruments

National Instruments 5783 Bedienungsanleitung

National Instruments

National Instruments 68M-50F STEP Bedienungsanleitung

National Instruments

National Instruments NI 5751 Bedienungsanleitung

National Instruments

National Instruments NI 6584R Bedienungsanleitung

National Instruments

National Instruments SCXI-1349 Bedienungsanleitung

National Instruments

National Instruments NI 1483 Bedienungsanleitung

National Instruments

National Instruments 1483R Bedienungsanleitung

National Instruments

National Instruments BNC-2110 Bedienungsanleitung

National Instruments

National Instruments DAQ SC-205X Series Bedienungsanleitung

National Instruments

National Instruments TC-2190 Bedienungsanleitung

National Instruments

National Instruments VXI-1000 Bedienungsanleitung

National Instruments

National Instruments REM-11180 Bedienungsanleitung

National Instruments

National Instruments TC-2095 Bedienungsanleitung

National Instruments

National Instruments NI-5752B Bedienungsanleitung

National Instruments

National Instruments BNC-2115 Bedienungsanleitung

National Instruments

National Instruments PCI/PXI ETHERNET ADAPTERS Bedienungsanleitung

National Instruments

National Instruments USB-6001 Bedienungsanleitung

National Instruments

National Instruments PCI/PXI GIGABIT ETHERNET ADAPTERS Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung