National Instruments BNC-2142 Bedienungsanleitung

natinst.com

™

and

National Instruments

™

are trademarks of National Instruments Corporation. Product and company names mentioned herein

are trademarks or trade names of their respective companies.

322545A-01

INSTALLATION GUIDE

BNC-2142 DESKTOP AND DIN RAIL-MOUNTABLE

BNC ADAPTER

This installation guide describes how to install and configure your

BNC-2142 accessory.

Introduction

The BNC-2142 is a desktop and DIN rail-mountable BNC adapter you

can connect directly to dynamic signal acquisition (DSA) devices. It

includes six BNC connectors for signal connections, and a 68-pin

I/O connector for connection to the PCI-445xand NI 455xDSA devices.

The BNC-2142 is ideal for simplifying connections between your

measurement apparatus and your DSA device in laboratory, test, and

production environments.

What You Need to Get Started

To set up and use your BNC-2142 accessory, you will need the following:

❑BNC-2142 BNC Adapter

❑BNC-2142 Desktop and DIN Rail-Mountable BNC Adapter

Installation Guide

❑PCI-445x or NI 455xdevice

❑SHC68-C68-A1 analog cable

Detailed specifications for the BNC-2142 are in the Specifications section

later in this guide.

BNC-2142 Installation Guide 2 www.natinst.com

Connecting Signals to Your BNC-2142

This section describes how to connect field signals to your BNC-2142

accessory.

Table 1 describes the BNC connectors available on the front panel of your

BNC-2142.

Note All BNC connectors on the BNC-2142 are single-ended only. The outer shells of the

BNC connectors are in direct contact with the metal enclosure of the BNC-2142, which is

grounded via the SHC68-C68 analog cable shield to the chassis ground of your computer.

Caution Connecting ground-referenced sources to the analog inputs or ground-referenced

loads to the analog outputs may cause ground noise to be picked up from other electrical

equipment also referenced to the source or load ground. Additionally, if the source or load

ground is at a different electrical potential than the ground of the BNC-2142 and DSA

device, ground-loops may occur that can result in incorrect readings, and may damage the

BNC-2142, the DSA device, or the host computer. National Instruments is not liable for

damage resulting from these connections.

To avoid encountering these conditions, electrically isolate orfloat the source or load from

its reference ground to create single-ended connection with a single ground reference on

the BNC-2142.

Table 1. BNC-2142 Connector Signal Descriptions

Front Panel BNC

Connectors Signal Description

ACH<0..3> Single-ended Input Analog Channels 0

through 3

DAC0OUT Digital-to-AnalogConverter0Output—This

single-ended connector supplies the voltage

output of analog output channel 0.

DAC1OUT Digital-to-AnalogConverter1Output—This

single-ended connector supplies the voltage

output of analog output channel 1.

National Instruments Corporation 3 BNC-2142 Installation Guide

Connecting Analog Inputs

You can use the BNC-2142 to measure floating analog input signals. The

BNC-2142 connects to the analog input channels on the PCI-445xand

NI 455xDSA devices via the ACH<0..3> BNC connectors.

Connecting Analog Outputs

The BNC-2142 connects to the analog output channels on the PCI-445x

and NI 455xDSA devices via the DAC0OUT and DAC1OUT BNC

connectors.

Cabling

The BNC-2142 has one 68-position 0.8 mm VHDCI connector on the rear

panel to connect to your DSA device.

Caution Do not connect the BNC-2142 to any device other than the National Instruments

PCI-445xand NI 455xDSA devices. Doing so can damage the BNC-2142, the DSA

device, or host computer. National Instruments is not liable for damages resulting from

these connections.

BNC-2142 Installation Guide 4 www.natinst.com

Installing Your BNC-2142

Perform the following steps to connect your BNC-2142 to your DSA

device. Consult your computer user manual or technical reference manual

for specific instructions and warnings.

Note You can either place the BNC-2142 on a workbench near the host computer or use

the available DIN rail-mount kit.

1. Connect the BNC-2142 to your DSA device.

2. Connect the field signals to the BNC connectors. Refer to the

Connecting Signals to Your BNC-2142 section earlier in this guide for

more information.

When you have finished using your BNC-2142, turn off any powered

external signals connected to your BNC-2142 before you turn off your

computer.

Figure 1. Connecting the BNC-2142 to Your DSA Device

Warning The BNC-2142 is not designed for input voltages greater than ±42.4 V, even if a

user-installed voltage divider reduces the voltage to within the input range of the DSA

device. Input voltages greater than ±42.4 V can damage the BNC-2142, any device

connected to it, and the host computer. Overvoltage can also cause an electric shock hazard

for the operator. National Instruments is notliable for damage or injury resulting from such

misuse.

1 BNC-2142 2 Shielded Cable 3 DSA Device 4 Personal Computer

National Instruments Corporation 5 BNC-2142 Installation Guide

Specifications

This section lists the specifications of the BNC-2142. These specifications

are typical at 25 °C unless otherwise specified.

Electrical

Max input voltage ..................................Each input should remain within

±42.4 V (30 Vrms) of ground

Field connection.....................................6 BNC connectors

(4 single-ended analog input

connectors, and 2 single-ended

analog output connectors)

Physical

Dimensions.............................................14.4 by 11.2 by 5.5 cm

(5.7 by 4.4 by 2.2 in.)

I/O connector..........................................One 68-pin 0.8 mm VHDCI

female connector

BNC connectors.....................................6

Environment

Operating temperature............................0 to 70 °C

Storage temperature ...............................–55 to 150 °C

Relative humidity...................................5% to 90% noncondensing

Inhaltsverzeichnis

Andere National Instruments Adapter Handbücher

National Instruments

National Instruments 5741 Bedienungsanleitung

National Instruments

National Instruments PCI/PXI ETHERNET ADAPTERS Bedienungsanleitung

National Instruments

National Instruments BNC-2110 Bedienungsanleitung

National Instruments

National Instruments TC-2095 Bedienungsanleitung

National Instruments

National Instruments 68M-50F STEP Bedienungsanleitung

National Instruments

National Instruments BNC-2110 Bedienungsanleitung

National Instruments

National Instruments VXI-1000 Bedienungsanleitung

National Instruments

National Instruments DAQ SC-205X Series Bedienungsanleitung

National Instruments

National Instruments SCXI-1349 Bedienungsanleitung

National Instruments

National Instruments SCXI 1346 Bedienungsanleitung

National Instruments

National Instruments BNC-2144 Bedienungsanleitung

National Instruments

National Instruments 5762R Bedienungsanleitung

National Instruments

National Instruments PCI/PXI GIGABIT ETHERNET ADAPTERS Bedienungsanleitung

National Instruments

National Instruments NI 9147 Bedienungsanleitung

National Instruments

National Instruments NI-6589 Bedienungsanleitung

National Instruments

National Instruments 5783 Bedienungsanleitung

National Instruments

National Instruments BNC-2115 Bedienungsanleitung

National Instruments

National Instruments SC-2042-RTD Bedienungsanleitung

National Instruments

National Instruments SC-2072 Bedienungsanleitung

National Instruments

National Instruments NI 5782R Bedienungsanleitung

National Instruments

National Instruments NI 6535 Bedienungsanleitung

National Instruments

National Instruments TC-2190 Bedienungsanleitung

National Instruments

National Instruments NI 9949 RJ-50 Bedienungsanleitung

National Instruments

National Instruments 653 Series Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung